DoALL Cutting Fluids
2375b Touhy
Elk Grove Village, IL 60007
Phone: 888/362-5572 x68916 鈥? Fax: 847/803-1447
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: Power-Cut鈩? 480
PRODUCT CLASS: WATER SOLUBLE OIL CUTTING FLUID
MSDS No.: MS934
SECTION I : MANUFACTURER IDENTIFICATION
MANUFACTURER'S NAME: DoALL COMPANY
ADDRESS: 1480 S. Wolf Rd. Wheeling, IL 60090
EMERGENCY PHONE: (800) 535-5053 (INFOTRAC)
INFORMATION: (888) 362-5572 x68916
REVISION DATE: May 1, 2006
SECTION II: HAZARDOUS INGREDIENTS IDENTIFICATION
OCCUPATIONAL EXPOSURE LIMITS
INGREDIENTS CAS #: OSHA PEL: ACGIH TLV: PERCENT:
Severely Hydro-
treated Naphthenic
Oil 64742-52-5 5mg./cu. m. 5mg./cu. m. 75.0-80.0
Diethylene Glycol 111-46-6 25 ppm 25 ppm 1.0-2.0
SECTION III: PHYSICAL DATA
Boiling Point: >212 degrees Fahrenheit
Specific Gravity: 0.915 (Water = 1)
Vapor Pressure: ND
Melting Point: NA
Vapor Density: >1 (air = 1)
Evaporation Rate: ND (BuAc = 1)
Solubility in Water: Emulsifies
pH: 9.2 (@ 5%)
Appearance: Amber liquid
Odor: Oily aroma
Page 1 of 3
SECTION IV: FIRE AND EXPLOSION DATA
350 掳F COC.
FLASH POINT:
EXTINGUISHING MEDIA: Carbon Dioxide, Foam, or Dry Chemical.
FIRE FIGHTING PROCEDURES: Water stream or spray, to cool containers to prevent vapor formation and
ignition, may spread fire. Fog nozzles are preferred if water is used. Wear SCBA
gear in fire area.
UNUSUAL FIRE AND
EXPLOSION HAZARDS: None.
SECTION V: HEALTH HAZARD DATA
ROUTES OF EXPOSURE AND EFFECTS OF OVER-EXPOSURE:
INHALATION: Breathing difficulty.
EYE CONTACT:Minor irritation.
SKIN CONTACT: Minor irritation.
SKIN ABSORPTION: Not expected to occur.
INGESTION: Nausea, and/or diarrhea.
CARCINOGENICITY:
LISTED BY NTP: No
LISTED BY IARC: No
LISTED BY OSHA: No
EMERGENCY FIRST AID PROCEDURES:
INHALATION: Remove person to fresh air. If necessary, support breathing. Get Medical attention.
EYE CONTACT: Flush with water for 15 minutes. If irritation persists, get Medical attention.
SKIN CONTACT: Wash exposed area with mild soap and warm water only. Do not use harsh soap or
solvent. Wash stained clothing before reusing.
SKIN ABSORPTION: Get medical attention.
INGESTION: Keep person warm and quiet. Get Medical attention. Do not induce vomiting.
SECTION VI: REACTIVITY DATA
STABILITY: Stable.
INCOMPATIBILITY: Strong oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Oxides of carbon, and sulfur compounds.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII: HANDLING PRECAUTIONS
IN CASE OF ACCIDENTAL RELEASE:
SMALL SPILLS: Use absorbent material.
LARGE SPILLS: Dike and pump into drums.
RESIDUE: Mop with soap and water.
WASTE DISPOSAL METHOD: Treat as an oily waste and dispose of in accordance with all local, state, and
federal regulations.
STORAGE: Store dry in a closed container in a cool place away from any fire source.
OTHER PRECAUTIONS: NA
Page 2 of 3
SECTION VIII: PROTECTIVE MEASURES
VENTILATION: General mechanical ventilation should be adequate. If misting occurs, provide local
ventilation.
PROTECTIVE GLOVES: The use of NEOPRENE gloves that are impermeable to oil is recommended.
EYE PROTECTION: Safety goggles with side shields or face shield are recommended.
OTHER PROTECTION: An emergency shower and eyewash should be available in the work area. Practice
reasonable personal hygiene. Wash exposed skin with mild soap and warm water only.
Oil-soaked clothing should be changed promptly and laundered before re-wearing.
SECTION IX: REGULATION COMPLIANCE INFORMATION
CAA: Contains no ozone depleting substance.
DOT: Not classified as hazardous.
RCRA: As received, not a hazardous waste material.
SARA: None.
TSCA: All ingredients are registered.
VOC: None.
SECTION X: HMIS
HEALTH: 1
FLAMMABILITY: 1
REACTIVITY: 0
Abbreviations and Symbols used in this MSDS:
NA Not Applicable < - Less Than
ND Not Determined > - Greater Than
BuAc Butyl Acetate
Data in this MSDS is believed to be correct and reliable. However, The DoALL Co. does not assume
responsibility for it, or any recommendations contained in it, inasmuch as conditions and methods of use
are beyond our control. Further, we make no warranty, expressed or implied, of any kind regarding this
product or its use, and purchaser assumes all risks of use or handling either in accordance with directions
or not.
The information contained within this document is property of DoALL Cutting Fluids. Alteration to this document in any form is against the law.
While the information released from DoALL Cutting Fluids is accurate and up to date, we cannot protect from unlawful editing and changing of
the information. We cannot guarantee any information unless it is received directly from DoALL Cutting Fluids. We accept no responsibility for
what happens to this information once it leaves our offices. Please only trust information received directly from DoALL.
Page 3 of 3
|