DoALL Cutting Fluids
2375b Touhy
Elk Grove Village, IL 60007
Phone: 888/362-5572 x68916 鈥? Fax: 847/803-1447
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: Tuff Kut庐
PRODUCT CLASS: WATER SOLUBLE OIL CUTTING FLUID
MSDS No.: MS939
SECTION I: MANUFACTURER IDENTIFICATION
MANUFACTURER'S NAME: DoALL COMPANY
ADDRESS: 1480 S. Wolf Rd. Wheeling, IL 60090
EMERGENCY PHONE: (800) 535-5053 (INFOTRAC)
INFORMATION: (888) 362-5572 x68916
REVISION DATE: May 1, 2006
SECTION II: HAZARDOUS INGREDIENTS IDENTIFICATION
OCCUPATIONAL EXPOSURE LIMITS
INGREDIENTS: CAS #: OSHA PEL: ACGIH TLV: PERCENT:
Heavy Naphthenic, severely 64742-52-5 5mg./cu..m. ------------ 30-55%
hydrotreated chemically neutralized oil
Triethanolamine 102-71-6 1-5%
SECTION III: PHYSICAL DATA
Boiling Point: 105 degrees Celsius
Specific Gravity: 0.95 (Water = 1)
Vapor Pressure: Not Established
Melting Point: NA
Vapor Density: NA
Evaporation Rate Not Established (BuAc = 1)
Solubility in Water: 100%
pH: (@ 5%) = 9.2
Appearance: Amber Liquid
Odor: Mild
Page 1 of 3
SECTION IV: FIRE AND EXPLOSION DATA
355 掳F COC.
FLASH POINT:
EXTINGUISHING MEDIA: Carbon Dioxide, Foam, or Dry Chemical. NOTE: Water, Fog, and Foam may
cause frothing and spattering
FIRE FIGHTING PROCEDURES: Wear self-contained breathing apparatus and chemical resistant clothing. Use
water spray to cool fire exposed containers.
UNUSUAL FIRE AND
EXPLOSION HAZARDS: Burning will cause oxides of carbon, hydrogen chloride, and sulfur.
SECTION V: HEALTH HAZARD DATA
ROUTES OF EXPOSURE AND EFFECTS OF OVER-EXPOSURE:
SIGNS AND SYMPTOMS OF OVEREXPOSURE: Acute and Chronic Overexposure- None
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: An irritation may be present on the
skin for persons with allergies to detergents or oils.
CARCINOGENICITY:
LISTED BY NTP: No
LISTED BY IARC: No
LISTED BY OSHA: No
EMERGENCY FIRST AID PROCEDURES:
INHALATION: Remove person to fresh air. If necessary, support breathing. Get Medical attention.
EYE CONTACT: Flush with water for 15 minutes. If irritation persists, get Medical attention.
SKIN CONTACT: Wash exposed area with mild soap and warm water only. Do not use harsh soap or
solvent.
SKIN ABSORPTION: Avoid prolonged contact with undiluted concentrate.
INGESTION: Induce vomiting and seek medical attention.
SECTION VI: REACTIVITY DATA
STABILITY: Stable.
INCOMPATIBILITY: Strong acids and oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition may produce oxides of carbon, sulfur,
and hydrogen chloride.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION VII: HANDLING PRECAUTIONS
IN CASE OF ACCIDENTAL RELEASE:
SMALL SPILLS: Use absorbent material.
LARGE SPILLS: Dike and pump into drums.
RESIDUE: Mop with soap and water.
WASTE DISPOSAL METHOD: Treat as an oily waste and dispose of in accordance with all local, state, and
federal regulations.
STORAGE: Store dry in a closed container in a cool place away from excessive heat or
oxidizers.
OTHER PRECAUTIONS: None.
Page 2 of 3
SECTION VIII PROTECTIVE MEASURES
VENTILATION: Local exhaust.
PROTECTIVE GLOVES: Not normally required.
EYE PROTECTION: Not normally required.
OTHER PROTECTION: An emergency shower and eyewash should be available in the work area. Practice
reasonable personal hygiene. Wash exposed skin with mild soap and warm water only.
Oil-soaked clothing should be changed promptly and laundered before re-wearing.
SECTION IX: REGULATION COMPLIANCE INFORMATION
CAA: Contains no ozone depleting substance.
DOT: Not classified as hazardous.
RCRA: As received, not a hazardous waste material.
SARA: None.
TSCA: All ingredients are registered.
VOC: None.
SECTION X: HMIS
HEALTH: 1
FLAMMABILITY: 1
REACTIVITY: 0
Abbreviations and Symbols used in this MSDS:
NA Not Applicable < - Less Than
ND Not Determined > - Greater Than
BuAc Butyl Acetate
Data in this MSDS is believed to be correct and reliable. However, The DoALL Co. does not assume
responsibility for it, or any recommendations contained in it, inasmuch as conditions and methods of use
are beyond our control. Further, we make no warranty, expressed or implied, of any kind regarding this
product or its use, and purchaser assumes all risks of use or handling either in accordance with directions
or not.
The information contained within this document is property of DoALL Cutting Fluids. Alteration to this document in any form is against the law.
While the information released from DoALL Cutting Fluids is accurate and up to date, we cannot protect from unlawful editing and changing of
the information. We cannot guarantee any information unless it is received directly from DoALL Cutting Fluids. We accept no responsibility for
what happens to this information once it leaves our offices. Please only trust information received directly from DoALL.
Page 3 of 3
|