DoALL Cutting Fluids
1228-H Harding Avenue
Des Plaines, IL 60016
Phone: 847/803-7262 鈥? Fax: 847/803-1447
MATERIAL SAFETY DATA SHEET
==============================================================================
MS208 Power-Cut鈩? 511 Page 1 of 3
==============================================================================
PRODUCT NAME: Power-Cut鈩? 511
PRODUCT CLASS: WATER SOLUBLE OIL CUTTING FLUID
=== SECTION I MANUFACTURER IDENTIFICATION ==============
MANUFACTURER'S NAME: DoALL COMPANY
ADDRESS: 254 No. Laurel Ave. Des Plaines, IL 60016.
EMERGENCY PHONE: (800) 535-5053 (INFOTRAC)
INFORMATION: (847) 803-7262
REVISION DATE: April 2, 2004
=== SECTION II HAZARDOUS INGREDIENTS IDENTIFICATION ==============
OCCUPATIONAL EXPOSURE LIMITS
INGREDIENTS: CAS #: OSHA PEL: ACGIH TLV: PERCENT:
Severely Hydro-
treated Naphthenic
Oil 64741-86-2 5mg./cu..m. 5mg./cu. m. 55.0-70.0
=== SECTION III PHYSICAL DATA ==============
Boiling Point: >212 degrees Fahrenheit
Specific Gravity: 0.948 (Water = 1)
Vapor Pressure: ND
Melting Point: NA
Vapor Density: ND
Evaporation Rate ND (BuAc = 1)
Solubility in Water: Emulsifies
pH: 9.5 (@ 5%)
Appearance: Dark Amber Liquid
Odor: Oily aroma
==============================================================================
MS208 Power-Cut鈩? 511 Page 2 of 3
==============================================================================
=== SECTION IV FIRE AND EXPLOSION DATA ==============
350 掳F COC.
FLASH POINT:
EXTINGUISHING MEDIA: Carbon Dioxide, Foam, or Dry Chemical.
FIRE FIGHTING PROCEDURES: Water stream or spray, to cool containers to prevent vapor formation and
ignition, may spread fire. Fog nozzles are preferred if water is used. Wear
SCBA gear in fire area.
UNUSUAL FIRE AND
EXPLOSION HAZARDS: None.
=== SECTION V HEALTH HAZARD DATA ==============
ROUTES OF EXPOSURE AND EFFECTS OF OVER-EXPOSURE:
INHALATION: Breathing difficulty.
EYE CONTACT: Minor irritation.
SKIN CONTACT: Slight defatting, and/or minor irritation if compostion decomposes.
SKIN ABSORPTION: Not expected to occur.
INGESTION: Nausea, and/or diarrhea.
CARCINOGENICITY:
LISTED BY NTP: No
LISTED BY IARC: No
LISTED BY OSHA: No
EMERGENCY FIRST AID PROCEDURES:
INHALATION: Remove person to fresh air. If necessary, support breathing. Get Medical attention.
EYE CONTACT: Flush with water for 15 minutes. If irritation persists, get Medical attention.
SKIN CONTACT: Wash exposed area with mild soap and warm water only. Do not use harsh soap or
solvent.
SKIN ABSORPTION: Avoid prolonged contact with undiluted concentrate.
INGESTION: Keep person warm and quiet. Get Medical attention. Do not induce vomiting.
=== SECTION VI REACTIVITY DATA ==============
STABILITY: Stable.
INCOMPATIBILITY: Strong oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Oxides of carbon, sulfur and nitrogen compounds, and
hydrogen chloride.
HAZARDOUS POLYMERIZATION: Will not occur.
=== SECTION VII HANDLING PRECAUTIONS ==============
IN CASE OF ACCIDENTAL RELEASE:
SMALL SPILLS: Use absorbent material.
LARGE SPILLS: Dike and pump into drums.
RESIDUE: Mop with soap and water.
WASTE DISPOSAL METHOD: Treat as an oily waste and dispose of in accordance with all local, state, and
federal regulations.
STORAGE: Store dry in a closed container in a cool place away from any fire source.
OTHER PRECAUTIONS: Avoid breathing MIST when handling concentrate.
==============================================================================
MS208 Power-Cut鈩? 511 Page 3 of 3
==============================================================================
=== SECTION VIII PROTECTIVE MEASURES ==============
VENTILATION: General mechanical ventilation should be adequate.
PROTECTIVE GLOVES: The use of NEOPRENE gloves that are impermeable to oil is recommended using
concentrate.
EYE PROTECTION: Safety goggles with side shields or face shield are recommended.
OTHER PROTECTION: An emergency shower and eyewash should be available in the work area. Practice
reasonable personal hygiene. Wash exposed skin with mild soap and warm water only.
Oil-soaked clothing should be changed promptly and laundered before re-wearing.
=== SECTION IX REGULATION COMPLIANCE INFORMATION ==============
CAA: Contains no ozone depleting substance.
DOT: Not classified as hazardous.
RCRA: As received, not a hazardous waste material.
SARA: None.
TSCA: All ingredients are registered.
VOC: None.
=== SECTION X HMIS ==============
HEALTH: 1
FLAMMABILITY: 1
REACTIVITY: 0
==============================================================================
==============================================================================
Abbreviations and Symbols used in this MSDS:
NA Not Applicable < - Less Than
ND Not Determined > - Greater Than
BuAc Butyl Acetate
==============================================================================
Data in this MSDS is believed to be correct and reliable. However, The DoALL Co. does not assume
responsibility for it, or any recommendations contained in it, inasmuch as conditions and methods of use
are beyond our control. Further, we make no warranty, expressed or implied, of any kind regarding this
product or its use, and purchaser assumes all risks of use or handling either in accordance with directions
or not.
The information contained within this document is property of DoALL Cutting Fluids. Alteration to this document
in any form is against the law. While the information released from DoALL Cutting Fluids is accurate and up to
date, we cannot protect from unlawful editing and changing of the information. We cannot guarantee any
information unless it is received directly from DoALL Cutting Fluids. We accept no responsibility for what
happens to this information once it leaves our offices. Please only trust information received directly from DoALL.
==============================================================================
|