Pro Stix #3
Page 1 of 3
MATERIAL SAFETY DATA SHEET
SECTION I: IDENTIFICATION OF PRODUCT
PRODUCT NAME: Pro Stix #3 ( Soap Stick)
PRODUCT USE: Oil Well Fluid Additive CAS NO. 9016-45-9
CHEMICAL FAMILY: Surfactant Blend
WORK PLACE HAZARDOUS MATERIALS INFORMATION SYSTEM (WHMIS)
WHMIS CLASSIFICATION: Not Controlled under WHMIS
WORK PLACE HAZARD: Cause irritation
TRANSPORTATION OF DANGEROUS GOODS (TDG)
SHIPPING NAME: Not regulated under TDG
TDG CLASSIFICATION: N/A
UN NUMBER (PIN): N/A
PACKING GROUP: N/A
SECTION II: HAZARDOUS INGREDIENTS
INGREDIENT PERCENT CAS NUMBER LD RAT OSHA PEL ACGIH TLV
(50)
Alkyl Phenol Ethoxylate Confidential 9016-45-9 N/A N/A N/A
SECTION III: TOXICOLOGICAL PROPERTIES
ROUTE OF ENTRY: [XX] SKIN [XX] EYE CONTACT [XX] INHALATION [XX] INGESTION
EYE CONTACT: May cause eye irritation.
SKIN CONTACT: Repeated or prolonged contact will cause drying and defatting of skin leading to
irritation.
INGESTION: May cause headache, dizziness, nausea, diarrhoea and other central nervous system
effects.
INHALATION: May cause headache, dizziness, nausea, and other central nervous system effects.
SECTION IV: FIRST AID MEASURES
SKIN CONTACT: Immediately wash skin with soap and plenty of water for at least 15 minutes and get
medical attention if symptoms persist.
Pro Stix #3
Page 2 of 3
MATERIAL SAFETY DATA SHEET
EYE CONTACT: Flush immediately with plenty of soap and water for at least 15 minutes and get
medical attention if symptoms persist.
INGESTION: If swallowed, induce vomiting by giving two glasses of water to drink and sticking
finger down throat. Consult a physician. Never give anything by mouth to an
unconscious person.
INHALATION: If inhaled, remove to fresh air. If not breathing, give artificial respiration, preferably
mouth to mouth. If breathing is difficult, give oxygen. Get medical attention.
SECTION V: PHYSICAL DATA
APPEARANCE AND ODOUR: Odourless solid
SPECIFIC GRAVITY(@ 20掳C): 1.056
BOILING POINT (掳 C): N/D
FREEZING POINT (掳C): N/D
SOLUBILITY IN WATER: Soluble
pH: 6.0-8.0
PERCENT VOLATILE BY VOLUME: N/D
EVAPORATION RATE: N/A
VAPOUR PRESSURE (mm Hg): N/D
VAPOUR DENSITY (Air = 1): N/D
SECTION VI: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: None
FLAMMABLE LIMITS: N/D
EXTINGUISHING MEDIA: Dry powder, CO2, or alcohol foam
SPECIAL FIRE FIGHTING PROCEDURES: N/A
UNUSUAL FIRE AND EXPLOSION HAZARDS: Containers may explode from internal pressure if confined to
fire. Cool with water. Keep unnecessary people away.
SECTION VII: REACTIVITY DATA
STABILITY: Stable [XX] Unstable [ ]
Pro Stix #3
Page 3 of 3
MATERIAL SAFETY DATA SHEET
INCOMPATIBILITY (CONDITIONS TO AVOID): Strong oxidizing agents
CONDITIONS OF REACTIVITY: Ignition sources
HAZARDOUS DECOMPOSITION PRODUCTS: From fire: Smoke, CO2, CO, oxides of phosphorous, and
oxides of nitrogen.
HAZARDOUS POLYMERIZATION: Will Not Occur [XX] May Occur [ ]
SECTION VIII: PREVENTIVE MEASURES
SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: Not normally required.
VENTILATION: Local exhaust.
PROTECTIVE GLOVES: Wear impervious gloves.
EYE PROTECTION: Use goggles or face shield if splashing is likely.
OTHER PROTECTIVE EQUIPMENT (Specify): Not normally required.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Keep away from heat, sparks, and open flame. Use with adequate ventilation. Do not breathe vapours. Avoid
prolonged or repeated contact with skin. Store in cool, dry place away from ignition sources, oxidizers or materials
bearing a yellow 鈥渄ot鈥? label.
STEPS TO BE TAKEN IN CASE THE MATERIAL IS SPILLED OR RELEASED
In case of spillage, absorb with inert material and dispose of in accordance with applicable regulations.
WASTE DISPOSAL METHOD
Follow Federal and State regulations.
SECTION IX: PREPARATION
THE INFORMATION CONTAINED HEREIN IS GIVEN IN GOOD FAITH, BUT NO WARRANTY, EXPRESSED OR
IMPLIED, IS MADE.
DATE PRINTED: April 6, 2006 BY: MILLENNIUM TECHNOLOGIES LTD.
DATE MODIFIED: July 14, 2004 APPROVED BY:
SUPERSEDES: February, 2001
|