MATERIAL SAFETY DATA SHEET
SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name: Star brite Liquid Electrical Tape (Black, Red, Green, White and Clear)
Product No: #84104B, 84105B,84106B,84107B,84108B,84134,84135,84136,84137,84138,84154,84155,84156,84157,84158,
841GA5
Manufacturer: STAR BRITE
4041 S. W. 47 AVENUE
FT. LAUDERDALE, FL 33314
Information Phone: 954-587-6280 Emergency Phone: 800-424-9300 or 703-527-3887 (Chemtrec)
Prepared by Jeff Tieger Prepared: January 17, 2007
SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS
ITEM NO. CHEMICAL NAME CAS NUMBER WT. PERCENT RANGE
01 XYLENE 1330-20-7 14%
02 ACETONE 67-64-1 5%
03 METHYL ETHYL KETONE 78-93-3 40%
- - - - - - - - - - EXPOSURE LIMITS- - - - - - - - - - -
ACGIH OSHA PEL- COMPANY
ITEM NO. TLV-TWA TLV-STEL PEL-TWA CEILING TLV-TWA SKIN
01 100 PPM 150 PPM N.A. N.A. NO
02 N.A. N.A. N.A. N.A. NO
03 200 PPM 300 PPM 200 PPM N.A. YES
(See Section 16 for abbreviation Legend)
SECTION 3 - HAZARDS IDENTIFICATION
***Emergency overview***: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical
attention. For skin, wash thoroughly with soap and water. If affected by inhalation of vapors or spray mist, remove to fresh air. If
swallowed, get medical attention immediately. If swallowed, do not induce vomiting. Keep person warm, quiet and get medical
attention. Aspiration of this material into the lungs due to vomiting can cause chemical pneumnitis which can be fatal.
Effects of overexposure - eye contact: Irritation. Symptoms are tearing, redness and discomfort. Causes eye, skin, nose and
throat irritation. Causes severe irritation, experienced as discomfort or pain, excess blinking and tear production, with marked
excess redness and swelling of the conjunctive. Severely irritating. If not removed promptly, will injure eye tissue which may result
in permanent damage.
Effects of overexposure - skin contact: Irritation. Can cause defatting of skin which may lead to dermatitis. Toxic by absorption
through skin with same effects as shown by inhalation. Prolonged exposure may cause a skin sensitization reaction in susceptible
individuals. Brief contact may cause slight irritation with itching and local redness.
Effects of overexposure - inhalation: Irritation to nose and throat. Extended or repeated exposure to concentrations above the
recommended exposure limits may cause brain or nervous system depression, with symptoms such as dizziness, headache. If
continued indefinitely, loss of consciousness, liver and kidney damage.
Reports have associated repeated or prolonged occupational overexposure to solvents with permanent brain and nervous system
damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Excessive inhalation
of vapors can cause respiratory irritation, dizziness, headache, nausea and asphyxiation. Use with caution.371. Due to its low
vapor pressure, the inhalation exposure hazard potential is regarded to be low. However if the product is heated, misted or
sprayed, concentrations above the recommended levels may be reached and mucous membranes and upper respiratory irritations
may result.
Product Name: Star brite Liquid Electrical Tape (Black, Red, Green, White and Clear)
Product No: #84104, 84105,84106,84107,84108,84134,84135,84136,84137,84138,84154,84155,84156,84157,84158, 841GA5
SECTION 3 - HAZARDS IDENTIFICATION cont鈥檇
Effects of overexposure - Ingestion: May cause mouth, throat, esophagus and stomach irritation, nausea, vomiting and diarrhea. If
ingested do not induce vomiting, keep person warm, quiet, and get medical attention. Aspiration of material into lungs can cause
chemical pneumonitis which can be fatal. Moderately toxic. May cause abdominal discomfort, nausea, vomiting and diarrhea.
Effects of overexposure - Chronic hazards: Reports have associated repeated and prolonged occupational overexposure to
solvents with permanent brain and nervous system damage. If swallowed, do not induce vomiting. Keep person warm, quiet and
get medical attention. Aspiration of this material into the lungs due to vomiting can cause chemical pneumonitis which can be fatal.
Primary route(s) of entry: Skin contact, inhalation, ingestion, eye contact.
SECTION 4 - FIRST AID MEASURES
First aid - Eye contact: In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical
attention immediately. Rinse with water for 15 minutes.
First aid - Skin contact: Wash with soap and water immediately. Wash affected area with soap and water. Remove contaminated
clothing. Consult a physician if irritation persists. Immediately remove contaminated clothing including shoes. Launder clothing
before reuse: do not re-use leather or absorbant shoes. Wash skin with mild soap and water; apply a good quality skin cream. If
irritation persists, consult a physician.
First aid - Inhalation: If affected by inhalation of vapors or spray mist, remove to fresh air. Remove victim to fresh air immediately.
If coughing, difficult breathing or any other respiratory symptoms develop, seek medical attention at once. Remove to fresh air if
difficulty in breathing.
First aid - Ingestion: If swallowed, get medical attention immediately!! If ingested do not induce vomiting. Keep person warm and
quiet, and get medical attention. Aspiration of material into lungs can cause chemical pneumonitis which can be fatal. Seek
medical attention.
SECTION 5 - FIRE FIGHTING MEASURES
Flash Point: 60掳 F (16掳 C) Lower Explosive Limit: 0.3%
(Setaflash Closed Cup) Upper Explosive Limit: 11.5%
Autoignition Temperature:
Extinguishing Media: Alcohol Foam CO2 Dry Chemical Foam Water Fog
Unusual fire and explosion hazards: Vapors may cause flash fire. Keep container tightly closed and isolate from heat, electrical
equipment, sparks and flame. Never use welding or cutting torch on or near drum (even empty) because product (even just
residue) can ignite explosively. Keep containers tightly closed. Isolate from heat, electrical equipment sparks and open flame.
Closed containers may explode when exposed to extreme heat. Vapors are heavier than air and may travel along the ground,
collect in low areas or may ignite at distant location. Do not weld on or near container, even when empty. Decomposition by
burning in open flame may yield toxic hydrogen chloride gas and combustion by-products. Water and foam may cause frothing.
Special fire fighting procedures: water spray may be used to reduce rate of burning and for cooling containers. Fire fighters and
others exposed to vapors or products of combustion should wear self-contained breathing apparatus. During emergency
conditions, decomposition products can cause health hazard. Use self-contained breathing apparatus with full face shield
operated in pressure demand or other positive; pressure mode. Burning will produce toxic fumes. Wear self-contained breathing
apparatus and full turn-out gear to fight fire. Do not direct a solid stream of water or foam into hot, burning pools. This may cause
frothing and increase fire intensity. Use self-contained breathing apparatus and protective clothing.
Product Name: Star brite Liquid Electrical Tape (Black, Red, Green, White and Clear)
Product No: #84104, 84105,84106,84107,84108,84134,84135,84136,84137,84138,84154,84155,84156,84157,84158, 841GA5
SECTION 6 - ACCIDENTAL RELEASE MEASURES
Steps to be taken in case material is released or spilled: remove all sources of ignition (flames, hot surfaces, and electrical, static,
or frictional sparks). Avoid breathing vapors. Ventilate area. Contain and remove with inert absorbent and non-sparking tools.
Remove all sources of ignition. Ventilate area. Absorb spill with an absorbent material such as sawdust, vermiculite or sand and
place material into a closed container. If large spill, dike area to prevent this material from entering water systems or sewers.
Wear protective equipment during cleanup. Eliminate all sources of ignition. Contain spill and absorb with absorbent material such
as sand. Shovel into drums or other suitable containers using non-sparking tools. Notify appropriate authorities if spill enters
environment. Collect for disposal. Avoid runoff to sewers or waterways. Wear suitable protective equipment. Vacuum with
H.E.P.A.. filter or use wet clean up technique to avoid dusting. Keep recovered material enclosed.
SECTION 7 - HANDLING AND STORAGE
Handling: Avoid prolonged or repeated inhalation of heated vapors or spray mists. Keep away from heat or open flame. Avoid
prolonged or repeated skin contact. Warning! Causes eye damage. May cause allergic skin reaction. Do not get in eyes, on skin
or on clothing. Harmful if swallowed or inhaled. Avoid breathing dust. Use with adequate ventilation. Warning !!! Harmful if
absorbed through the skin. Do not swallow. Causes eye and skin irritation. Keep containers tightly closed. No smoking or eating
in the handling areas. Wash thoroughly after handling.
Storage: Keep away from excessive heat, sparks and open flame. Keep closures tight when not in use. Keep containers upright
to prevent leakage. Store in cool, dry place. Protect from heat and flame. Store drum out of intense sunlight and away from heat.
Section 8 - EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering controls: Efficient local exhaust ventilation is required.
Respiratory protection: Do not breathe vapors. Wear an appropriate, properly fitted respirator (niosh/msha approved) during use
of this product until vapors are exhausted. Unless air monitoring demonstrates vapor levels are below applicable limits. Follow
respirator manufacturer's directions for respirator use. Observe standard 29cfr 1910.134. A canister type respirator must be worn
to prevent the inhalation of vapors or spray mists when the tlv or pel is exceeded. Approved niosh/msha (nuisance dust) is
necessary under certain conditions where airborne contaminants may exceed exposure limits. Use supplied air respiratory
protection in confined or enclosed spaces if needed.
Skin protection: Chemical resistant nitrile, neoprene or rubber gloves required. Rubber or plastic gloves.
Eye protection: Chemical goggles or face shield recommended. Safety glasses with side shields.
Other protective equipment: Wear protective clothing to prevent skin contact. Eye wash station and safety shower should be
available. Readily available eye wash fountain, safety shower. Remove and separately launder contaminated clothing before
reuse.
Hygienic practices: Wash hands before eating or smoking. Smoke in designated areas only.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
Boiling Range: 131 - 449掳 F Vapor Density: Is heavier than air
Odor: Solvent Odor Threshold: No information
Appearance: Black Liquid Evaporation Rate: Is faster than ether
Solubility In H20: No
Freeze Point: N/A Specific Gravity: 0.9752
Vapor Pressure: No information Ph @ 0.0%: N/A
Physical State: Heavy Liquid Viscosity : 1800-2000 CP
Coefficient of Water/Oil Distribution N/A
(See Section 16 for abbreviation legend)
Product Name: Star brite Liquid Electrical Tape (Black, Red, Green, White and Clear)
Product No: #84104, 84105,84106,84107,84108,84134,84135,84136,84137,84138,84154,84155,84156,84157,84158, 841GA5
SECTION 10 - STABILITY AND REACTIVITY
Conditions to avoid: Very high temperature and open flames.
Incompatibility: materials to avoid: amines, acids, and strong bases, strong alkalis. High temperatures in the presence of strong
bases. Acids. Strong oxidizing agents.
Hazardous decomposition products: burning can produce the following combustion products: Carbon monoxide and/or carbon
monoxide. Carbon monoxide is highly toxic if inhaled; carbon dioxide in sufficient concentrations can act as an asphyxiant.
Hydrogen chloride, Carbon monoxide, carbon dioxide and acetic acid. Carbon dioxide, carbon monoxide, various hydrocarbons.
Hazardous polymerization: Will not occur under normal conditions.
Stability: This product is stable under normal storage conditions.
SECTION 11 - TOXICOLOGICAL PROPERTIES
No product or component toxicological information is available.
SECTION 12 - ECOLOGICAL INFORMATION
Ecological information: No information
SECTION 13 - DISPOSAL CONSIDERATIONS
Disposal method: Obey relevant local, state and federal laws. Product is highly toxic to fish. Do not contaminate any lakes,
streams, ponds, underground water supply. Do not discharge effluent containing this product to sewer system without prior notice.
Dilute with an inert solvent and incinerate in a furnace where permitted under appropriate federal, state and local regulations.
Preferred disposal methods would be by supervised incineration at an approved chemical disposal area under federal, state and
local authority. Dispose of in accordance with local, state and federal regulations. Do not incinerate closed containers. Incinerate
in approved facility.
SECTION 14 - TRANSPORTATION INFORMATION
Call for information
SECTION 15 - REGULATORY INFORMATION
This product contains the following non-hazardous components:
- - - - - - - - - CHEMICAL NAME- - - - - - - - - - CAS NUMBER WT/WT %
Styrene-acrylate copolymer 68240-06-2 0.7%
U. S. FEDERAL REGULATIONS: AS FOLLOWS -
OSHA: Hazardous by definition of hazard communication standard (29 CFR 1910.1200)
Product Name: Star brite Liquid Electrical Tape (Black, Red, Green, White and Clear)
Product No: #84104, 84105,84106,84107,84108,84134,84135,84136,84137,84138,84154,84155,84156,84157,84158, 841GA5
SECTION 15 - REGULATORY INFORMATION cont鈥檇
CERCLA - Sara Hazard Category:
This product has been reviewed according to the EPA "Hazard Categories" promulgated under Sections 311 and 312 of the
Superfund Amendment and Reauthorization Act of 1986 (Sara Title III) and is considered, under applicable definitions, to meet the
following categories:
Sara Section 313:
This product contains the following substances subject to the reporting requirements of section 313 of title III of the Superfund
Amendments and Reauthorization Act of 1986 and 40 CFR Part 372:
- - - - - - - - - - - CHEMICAL NAME- - - - - - - - - - - CAS NUMBER
ERL 4221 2386-87-0
K-FLEX 120-55-8
VINYL CHLORIDE/VINYL ACETATE CO-POLYMER 9003-22-9
XYLENE 1330-20-7
ACETONE 67-64-1
METHYL ETHYL KETONE 78-93-3
PLIOLITE AC -4 68240-06-2
HGI-TALC 14807-96-6
COLORANT
Toxic Substances Control Act:
This product contains the following chemical substances subject to the reporting requirements of TSCA 12(b) if exported from the
United States:
- - - - - - - - - - CHEMICAL NAME- - - - - - - - - - - CAS NUMBER
ERL 4221 2386-87-0
K-FLEX 120-55-8
VINYL CHLORIDE/VINYL ACETATE CO-POLYMER 9003-22-9
XYLENE 1330-20-7
ACETONE 67-64-1
2-BUTANONE 78-93-3
STYRENE-ACRYLATE COPOLYMER 68240-06-2
International regulations: As follows -
Canadian WHMIS: This msds has been prepared in compliance with controlled product regulations except for use of the 16
headings.
Canadian WHMIS Class: Class B, Division 2
SECTION 16 - OTHER INFORMATION
HMIS Ratings - Health: 2 Flammabiltiy: 3 Reactivity: 0
Previous MSDS Revision date: 06/11//03
Volatile Organic Compounds: (VOCS): 5.43 LBS./GAL. 651 GRAMS/LTR
LEGEND: N.A. - Not Available N.E. - Not Established
N.D. - Not Determined
The information contained on this MSDS has been checked and should be accurate. However, it is the responsibility of the user to
comply with all federal, state and local laws and regulations.
|