MATERIAL SAFETY DATA SHEET
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
Gold Eagle Company
4400 S. Kildare Blvd.
Chicago, IL 60632-4372
(773) 376-4400
************************* HMIS RATINGS *************************
Health: 1 Flammability: 3 Reactivity: 0 Pers. Prot. Index: B
************************* NFPA RATINGS *************************
Health: 1 Fire: 3 Reactivity: 0 Specific Hazard: None
SECTION I PRODUCT IDENTITY
Product / Trade Name (s): FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part Number: FL111
MSDS Date: 05/14/03
CAS #: N/A
Category: N/A
Distributor: N/A
Chemical Name: N/A
Formula: N/A
Brief Description: Carb and Choke solvent cleaner.
SECTION II HAZARDOUS INGREDIENTS & EXPOSURE LIMITS
CHEMICAL NAME CAS # % LIMIT VALUES
DIACETONE ALCOHOL 123-42-2 10.00 PEL 50 ppm
PEL 240 mg/m3
ISOPROPANOL 67-63-0 30.00 PEL 400 ppm
PEL 980 mg/m3
XYLENE 1330-20-7 60.00 PEL 100 ppm
PEL 435 mg/m3
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point: 160 F. (71.1 C.)
Vapor Pressure (mm Hg.): N/A
Vapor Density (AIR = 1): >1.0
Solubility in Water: Partial
% Volatile / Volume: 100.0
Appearance and Odor: Water white liquid, solvent odor
pH: N/A
Specific Gravity (H2O = 1): 0.860
Page -1-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS (cont.)
Miscellaneous Information:
Product is flammable, keep away from sources of ignition, combustibles, oxidizing materials and acid.
Store in an area equipped with automatic sprinklers or fire extinguishing system. Empty containers
contain product residues, assume emptied containers to have same hazards as full containers.
SECTION IV FIRE AND EXPLOSION HAZARD DATA
Flash Point: 54 F. (12.2 C.) TOC
Flammable Limits: 1.0 TO 7.0
Lower Explosive Limit (LEL): 1.0
Upper Explosive Limit (UEL): 7.0
Extinguisher Media
Use halon replacement or carbon dioxide extinguishers or alcohol foam for small fires. Water spray or fog
can cool fire but may not be effective in extinguishing fire. Large fires should be extinguished with alcohol
foam. Use water spray to cool containers exposed to fire. Containers may explode in heat or fire.
Special Fire Fighting Procedures
Wear NIOSH approved SCBA respirator in the positive pressure mode and chemical protective clothing.
Unusual Fire and Explosion Hazards
Dangerous fire and explosion hazard when exposed to heat or flame. Isopropanol is extremely flammable
and forms explosive mixtures with air. Isopropanol vapors may travel considerable distance to a source of
ignition and flash back.
SECTION V REACTIVITY DATA
Stable: Yes
Hazardous Polymerization May Occur: No
Conditions to Avoid
Store in a well ventilated place away from sources of ignition, combustibles, oxidizing materials and acid.
Incompatibility (Material to Avoid)
Strong oxidizing agents, amines, chlorinated compounds and caustic materials.
Hazardous Decomposition or Byproducts
Excessive heating and/or incomplete combustion will produce carbon monoxide.
SECTION VI HEALTH HAZARD DATA
Effects on Eyes
Irritant.
Effects on Skin
Prolonged or repeated skin contact may cause dermatitis, scaling and possible systemic effects.
Effects Due to Ingestion
Low level of toxicity, small amounts of liquid aspirated into the respiratory system during ingestion may
cause pulmonary edema.
Effects Due to Inhalation
Narcotic chemical affecting central nervous system resulting in: dizziness, nausea, visual impairment,
narcosis and muscular impairment.
Page -2-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION VI HEALTH HAZARD DATA (cont.)
First Aid Procedures for Eyes
If the product contacts the eyes, immediately wash the eyes with large quantities of room temperature
water for at least 15 minutes, occasionally lifting the lower and upper lids. Get medical attention
immediately. A follow up visit to an opthalmologist should be made. Contact lenses should not be worn
when working with this chemical.
First Aid Procedures for Skin
If the product contacts the skin, promptly wash the contaminated skin with soap and water for at least 15
minutes. If this product penetrates the clothing, promptly remove the clothing and wash the skin with soap
and water. Systemic effects may be delayed 18 to 72 hours, therefore keep individual under observation.
First Aid Procedures for Ingestion
If this product is ingested. DO NOT INDUCE A PERSON TO VOMIT. Get medical attention
immediately.
First Aid Procedures for Inhalation
Move the exposed person to fresh air at once and call emergency medical care. If breathing has stopped,
give artificial respiration. If breathing is difficult, give humidified oxygen.
SECTION VII PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to Be Taken in Case Material is Released or Spilled
SMALL SPILL: Remove sources of heat or ignition, provide adequate ventilation, contain leak using
absorbent, inert, non-combustible material.
LARGE SPILL: Contain spill, transfer to secure containers. In the event of an uncontrolled material
release, the user should determine if release is reportable under applicable laws and regulations.
Waste Disposal Method
Dispose of product in accordance with local, state, and federal regulations. Before attempting clean up,
refer to other sections of MSDS for hazard warning information.
Precautions to Be Taken in Handling and Storing
See other sections of MSDS.
Other Precautions
Product is flammable, handle accordingly.
SECTION VIII CONTROL MEASURES
Local Exhaust: Provide local ventilation to maintain exposure levels below recommended
exposure limits.
Mechanical (General): In confined spaces, mechanical ventilation may be required.
Special Ventilation: N/A
Other Ventilation: N/A
Protective Gloves: Use natural rubber or neoprene gloves as required.
Eye Protection: Use splash proof chemical, safety goggles or appropriate full-face respirator.
Contact lenses should not be worn when working with this chemical.
Other Protective Clothing or Equipment
If there is a possibility of exposure of an individual鈥檚 body to the product, wear body-covering work
clothes to avoid prolonged or repeated exposure.
Work/Hygienic Practices
Use normal hygiene practices.
Page -3-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION VIII CONTROL MEASURES (cont.)
Respiratory Protection (Specify Type)
Do not use air purifying respirator. Use appropriate NIOSH approved supplied or self contained
respirator. Respirators must be selected based on the airborne levels found in the workplace and must not
exceed the working limits of the respirator.
SECTION IX ADDITIONAL INFORMATION
Additional Information
SHIPPING INFORMATION (CFR 49 AND IMDG):
PROPER SHIPPING NAME : Cleaning compound, N.O.I.
DOT HAZARD CLASS : Compounds, Gum Removing
(N.O.S.), Flammable Liquids, UN1993,
PGII, (Xylene, Isopropanol, Diacetone
Alcohol).
DOT UN NUMBER : None required.
IMDG SHIPPING NAME : Flammable Liquids, N.O.S., 3.2, UN1993
PGII (Xylene, Isopropanol, Diacetone
Alcohol), EmS#: 3-07.
SARA TITLE III:
Section 302: Xylene, 1330-20-7, RQ-1000 lbs.
Section 304: None
Section 311: Hazard categories-Fire Hazard=Yes; Acute=Yes and
Chronic=Yes.
Section 313: Xylene, 1330-20-7, 60%-70%.
CERCLA:
Section 311 (b) (4) : Requires discharges of crude oil and petroleum products in any kind or form to waters
must immediately be reported to the National Response Center at (800) 424-8802.
DISCLAIMER: Information presented herein is believed to be factual, as it has been derived from the
works and opinions of persons believed to be qualified experts. However, nothing contained in this
information is to be taken as warranty or representation for which the Gold Eagle Co. bears legal
responsibility. The user should review any recommendations in the specific context of the intended use to
determine whether they are appropriate.
Prepared by: Mike Profetto
Date: 05/14/03
While the information and recommendations set forth herein are believed to be accurate as of the MSDS date, Corbus, a
division of Compliance Management Systems, Inc., makes no warranties expressed or implied of fitness for a particular
purpose with respect hereto and disclaims all liability from reliance thereon.
Page -4-
MATERIAL SAFETY DATA SHEET
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
Gold Eagle Company
4400 S. Kildare Blvd.
Chicago, IL 60632-4372
(773) 376-4400
************************* HMIS RATINGS *************************
Health: 1 Flammability: 2 Reactivity: 0 Pers. Prot. Index: B
************************* NFPA RATINGS *************************
Health: 1 Fire: 2 Reactivity: 0 Specific Hazard: None
SECTION I PRODUCT IDENTITY
Product / Trade Name (s): FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part Number: FL107
MSDS Date: 05/14/03
CAS #: N/A
Category: N/A
Distributor: N/A
Chemical Name: N/A
Formula: N/A
Brief Description: Fuel system cleaner for automotive engines.
SECTION II HAZARDOUS INGREDIENTS & EXPOSURE LIMITS
CHEMICAL NAME CAS # % LIMIT VALUES
ADDITIVE MIXTURE (CAS#:MIXTURE) 5.00 N/A
PETROLEUM DISTILLATE 8008-20-6 80.00 N/A
PETROLEUM OIL (CAS#:MIXTURE) 15.00 N/A
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point: >200 F. (>95 C.)
Vapor Pressure (mm Hg.): N/A
Vapor Density (AIR = 1): <1.0
Solubility in Water: Negligible
% Volatile / Volume: 100.0
Appearance and Odor: Amber liquid, solvent odor
pH: N/A
Page -1-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS (cont.)
Specific Gravity (H2O = 1): 0.830
Miscellaneous Information
Product is combustible, keep away from sources of ignition, oxidizing materials and acid. Store in an area
equipped with automatic sprinklers or fire extinguishing system. Empty containers contain product
residues, assume emptied containers to have same hazards as full containers. Bond and ground all
equipment when transferring from one vessel to another vessel.
SECTION IV FIRE AND EXPLOSION HAZARD DATA
Flash Point: 125 F. (48.0 C.) TOC
Flammable Limits: 0.8 to 7.0
Lower Explosive Limit (LEL): 0.8
Upper Explosive Limit (UEL): 7.0
Extinguisher Media
Use carbon dioxide, dry chemical, foam and/or water fog as extinguishing media.
Special Fire Fighting Procedures
Wear NIOSH approved SCBA respirator in the positive pressure mode and chemical protective clothing.
Unusual Fire and Explosion Hazards
Water may cause frothing.
SECTION V REACTIVITY DATA
Stable: Yes
Hazardous Polymerization May Occur: No
Conditions to Avoid
Store below 150 F. Do not apply high heat or flame to container. Keep separate from strong oxidizing
agents.
Incompatibility (Material to Avoid)
Strong oxidants.
Hazardous Decomposition or Byproducts
Excessive heating and/or incomplete combustion will produce carbon monoxide.
SECTION VI HEALTH HAZARD DATA
Effects on Eyes
Irritant.
Effects on Skin
Irritant.
Effects Due to Ingestion
Toxicity is relatively low, there is a risk of aspiration of product into the lungs. On ingestion of large
quantities, slight GI discomfort, diarrhea, headache and nervous system depression may occur. Small
doses may produce irritation and diarrhea.
Page -2-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION VI HEALTH HAZARD DATA (cont.)
Effects Due to Inhalation
Low risk of inhalation. Mists above TLV may cause chemical pneumonitis.
First Aid Procedures for Eyes
If the product contacts the eyes, immediately wash the eyes with large quantities of room temperature
water for at least 15 minutes, occasionally lifting the lower and upper lids. Get medical attention
immediately.
First Aid Procedures for Skin
If the product contacts the skin, promptly wash the contaminated skin with soap and water for at least 15
minutes. If this product penetrates the clothing, promptly remove the clothing and wash the skin with soap
and water.
First Aid Procedures for Ingestion
Do not induce vomiting, product contains petroleum distillate. Get medical attention immediately.
First Aid Procedures for Inhalation
Move the exposed person to fresh air at once and call emergency medical care. If breathing has stopped,
give artificial respiration. If breathing is difficult, give humidified oxygen.
SECTION VII PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to Be Taken in Case Material is Released or Spilled
SMALL SPILL: Remove sources of heat or ignition, provide adequate ventilation, and contain leak using
absorbent, inert, non-combustible material.
LARGE SPILL: Contain spill, transfer to secure containers. In the event of an uncontrolled material
release, the user should determine if release is reportable under applicable laws and regulations.
Waste Disposal Method
Dispose of product in accordance with local, state, and federal regulations. Before attempting clean up,
refer to other sections of MSDS for hazard warning information.
Precautions to Be Taken in Handling and Storing
See other sections of MSDS
Other Precautions
Product is combustible, handle accordingly.
SECTION VIII CONTROL MEASURES
Local Exhaust: Provide local ventilation to maintain exposure levels below recommended
exposure limits.
Mechanical (General): In confined spaces, mechanical ventilation may be required.
Special Ventilation: OSHA TWA=5 mg/m3.
Other Ventilation: N/A
Protective Gloves: Use oil impervious gloves as required.
Eye Protection: Use splash proof chemical, safety goggles or appropriate full-face respirator.
Other Protective Clothing or Equipment
If there is a possibility of exposure of an individual鈥檚 body to the product, wear body-covering work
clothes to avoid prolonged or repeated exposure.
Page -3-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION VIII CONTROL MEASURES (cont.)
Work/Hygienic Practices
Use normal hygiene practices.
Respiratory Protection (Specify Type)
Normally none is required. If high vapor or mist concentration are expected, use appropriate NIOSH
approved respirator for organic vapors and mists. Respirators must be selected based on the airborne
levels found in the workplace and must not exceed the working limits of the respirator.
SECTION IX ADDITIONAL INFORMATION
Additional Information
SHIPPING INFORMATION (CFR 49 AND IMDG):
PROPER SHIPPING NAME : Cleaning Compound, N.O.I.
DOT HAZARD CLASS : Consumer commodity, ORM-D
DOT UN NUMBER : None required
IMDG SHIPPING NAME : Dangerous Goods in Limited Quantities of Class 3.3 (Petroleum
Distillates), PG III.
SARA TITLE III:
Section 302: None
Section 304: None
Section 311: None
Section 313: None
CERCLA:
Section 311 (b) (4): Requires discharges of crude oil and petroleum products in any kind or form to waters
must immediately be reported to the National Response Center at (800) 424-8802.
DISCLAIMER: Information presented herein is believed to be factual, as it has been derived from the
works and opinions of persons believed to be qualified experts. However, nothing contained in this
information is to be taken as warranty or representation for which the Gold Eagle Co. bears legal
responsibility. The user should review any recommendations in the specific context of the intended use to
determine whether they are appropriate.
Prepared by: Mike Profetto
Date: 05/14/03
While the information and recommendations set forth herein are believed to be accurate as of the MSDS date, Corbus, a
division of Compliance Management Systems, Inc., makes no warranties expressed or implied of fitness for a particular
purpose with respect hereto and disclaims all liability from reliance thereon.
Page -4-
MATERIAL SAFETY DATA SHEET
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
Gold Eagle Company
4400 S. Kildare Blvd.
Chicago, IL 60632-4372
(773) 376-4400
************************* HMIS RATINGS *************************
Health: 1 Flammability: 2 Reactivity: 0 Pers. Prot. Index: B
************************* NFPA RATINGS *************************
Health: 1 Fire: 2 Reactivity: 0 Specific Hazard: None
SECTION I PRODUCT IDENTITY
Product / Trade Name (s): FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part Number: OL106
MSDS Date: 05/14/03
CAS #: N/A
Category: N/A
Distributor: N/A
Chemical Name: N/A
Formula: N/A
Brief Description: Fuel system cleaner for automotive engines.
SECTION II HAZARDOUS INGREDIENTS & EXPOSURE LIMITS
CHEMICAL NAME CAS # % LIMIT VALUES
ADDITIVE MIXTURE (CAS#:MIXTURE) 5.00 N/A
PETROLEUM DISTILLATE 8008-20-6 80.00 N/A
PETROLEUM OIL (CAS#:MIXTURE) 15.00 N/A
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point: >200 F. (>95 C.)
Vapor Pressure (mm Hg.): N/A
Vapor Density (AIR = 1): <1.0
Solubility in Water: Negligible
% Volatile / Volume: 100.0
Appearance and Odor: Amber liquid, solvent odor
pH: N/A
Page -1-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS (cont.)
Specific Gravity (H2O = 1): 0.830
Miscellaneous Information
Product is combustible, keep away from sources of ignition, oxidizing materials and acid. Store in an area
equipped with automatic sprinklers or fire extinguishing system. Empty containers contain product
residues, assume emptied containers to have same hazards as full containers. Bond and ground all
equipment when transferring from one vessel to another vessel.
SECTION IV FIRE AND EXPLOSION HAZARD DATA
Flash Point: 125 F. (48.0 C.) TOC
Flammable Limits: 0.8 to 7.0
Lower Explosive Limit (LEL): 0.8
Upper Explosive Limit (UEL): 7.0
Extinguisher Media
Use carbon dioxide, dry chemical, foam and/or water fog as extinguishing media.
Special Fire Fighting Procedures
Wear NIOSH approved SCBA respirator in the positive pressure mode and chemical protective clothing.
Unusual Fire and Explosion Hazards
Water may cause frothing.
SECTION V REACTIVITY DATA
Stable: Yes
Hazardous Polymerization May Occur: No
Conditions to Avoid
Store below 150 F. Do not apply high heat or flame to container. Keep separate from strong oxidizing
agents.
Incompatibility (Material to Avoid)
Strong oxidants.
Hazardous Decomposition or Byproducts
Excessive heating and/or incomplete combustion will produce carbon monoxide.
SECTION VI HEALTH HAZARD DATA
Effects on Eyes
Irritant.
Effects on Skin
Irritant.
Effects Due to Ingestion
Toxicity is relatively low, there is a risk of aspiration of product into the lungs. On ingestion of large
quantities, slight GI discomfort, diarrhea, headache and nervous system depression may occur. Small
doses may produce irritation and diarrhea.
Page -2-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION VI HEALTH HAZARD DATA (cont.)
Effects Due to Inhalation
Low risk of inhalation. Mists above TLV may cause chemical pneumonitis.
First Aid Procedures for Eyes
If the product contacts the eyes, immediately wash the eyes with large quantities of room temperature
water for at least 15 minutes, occasionally lifting the lower and upper lids. Get medical attention
immediately.
First Aid Procedures for Skin
If the product contacts the skin, promptly wash the contaminated skin with soap and water for at least 15
minutes. If this product penetrates the clothing, promptly remove the clothing and wash the skin with soap
and water.
First Aid Procedures for Ingestion
Do not induce vomiting, product contains petroleum distillate. Get medical attention immediately.
First Aid Procedures for Inhalation
Move the exposed person to fresh air at once and call emergency medical care. If breathing has stopped,
give artificial respiration. If breathing is difficult, give humidified oxygen.
SECTION VII PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to Be Taken in Case Material is Released or Spilled
SMALL SPILL: Remove sources of heat or ignition, provide adequate ventilation, and contain leak using
absorbent, inert, non-combustible material.
LARGE SPILL: Contain spill, transfer to secure containers. In the event of an uncontrolled material
release, the user should determine if release is reportable under applicable laws and regulations.
Waste Disposal Method
Dispose of product in accordance with local, state, and federal regulations. Before attempting clean up,
refer to other sections of MSDS for hazard warning information.
Precautions to Be Taken in Handling and Storing
See other sections of MSDS
Other Precautions
Product is combustible, handle accordingly.
SECTION VIII CONTROL MEASURES
Local Exhaust: Provide local ventilation to maintain exposure levels below recommended
exposure limits.
Mechanical (General): In confined spaces, mechanical ventilation may be required.
Special Ventilation: OSHA TWA=5 mg/m3.
Other Ventilation: N/A
Protective Gloves: Use oil impervious gloves as required.
Eye Protection: Use splash proof chemical, safety goggles or appropriate full-face respirator.
Other Protective Clothing or Equipment
If there is a possibility of exposure of an individual鈥檚 body to the product, wear body-covering work
clothes to avoid prolonged or repeated exposure.
Page -3-
FL102 - VS7 Power 3 - 3 Step Fuel / Emission Service
Part #FL102 (FL107, FL111, OL104)
SECTION VIII CONTROL MEASURES (cont.)
Work/Hygienic Practices
Use normal hygiene practices.
Respiratory Protection (Specify Type)
Normally none is required. If high vapor or mist concentration are expected, use appropriate NIOSH
approved respirator for organic vapors and mists. Respirators must be selected based on the airborne
levels found in the workplace and must not exceed the working limits of the respirator.
SECTION IX ADDITIONAL INFORMATION
Additional Information
SHIPPING INFORMATION (CFR 49 AND IMDG):
PROPER SHIPPING NAME : Cleaning Compound, N.O.I.
DOT HAZARD CLASS : Consumer commodity, ORM-D
DOT UN NUMBER : None required
IMDG SHIPPING NAME : Dangerous Goods in Limited Quantities of Class 3.3 (Petroleum
Distillates), PG III.
SARA TITLE III:
Section 302: None
Section 304: None
Section 311: None
Section 313: None
CERCLA:
Section 311 (b) (4): Requires discharges of crude oil and petroleum products in any kind or form to waters
must immediately be reported to the National Response Center at (800) 424-8802.
DISCLAIMER: Information presented herein is believed to be factual, as it has been derived from the
works and opinions of persons believed to be qualified experts. However, nothing contained in this
information is to be taken as warranty or representation for which the Gold Eagle Co. bears legal
responsibility. The user should review any recommendations in the specific context of the intended use to
determine whether they are appropriate.
Prepared by: Mike Profetto
Date: 05/14/03
While the information and recommendations set forth herein are believed to be accurate as of the MSDS date, Corbus, a
division of Compliance Management Systems, Inc., makes no warranties expressed or implied of fitness for a particular
purpose with respect hereto and disclaims all liability from reliance thereon.
Page -4-
|