MATERIAL SAFETY DATA SHEET
Mighty Part # FL116 (consists of FL108, FL110, FL112)
FL108 - VS7 Supreme Fuel System Cleaner
Part #FL108
Gold Eagle Company
4400 S. Kildare Blvd.
Chicago, IL 60632-4372
(773) 376-4400
************************* HMIS RATINGS *************************
Health: 1 Flammability: 2 Reactivity: 0 Pers. Prot. Index: B
************************* NFPA RATINGS *************************
Health: 1 Fire: 2 Reactivity: 0 Specific Hazard: None
SECTION I PRODUCT IDENTITY
Product / Trade Name (s): FL108 - VS7 Supreme Fuel System Cleaner
Part Number: FL108
MSDS Date: 07/12/01
CAS #: N/A
Category: N/A
Distributor: N/A
Chemical Name: N/A
Formula: N/A
Brief Description: Fuel system cleaner for automotive engines.
SECTION II HAZARDOUS INGREDIENTS & EXPOSURE LIMITS
CHEMICAL NAME CAS # % LIMIT VALUES
ADDITIVE MIXTURE (CAS#:MIXTURE) 20.00 N/A
PETROLEUM DISTILLATE 8008-20-6 80.00 N/A
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point: >200 F. (>95 C.)
Vapor Pressure (mm Hg.): N/A
Vapor Density (AIR = 1): <1.0
Solubility in Water: Negligible
% Volatile / Volume: 100.0
Appearance and Odor: Amber liquid, solvent odor
pH: N/A
Specific Gravity (H2O = 1): 0.790
Miscellaneous Information:
Product is combustible, keep away from sources of ignition, oxidizing materials and acid. Store in an area
equipped with automatic sprinklers or fire extinguishing system. Empty containers contain product
residues, assume emptied containers to have same hazards as full containers. Bond and ground all
equipment when transferring from one vessel to another vessel.
Page -1-
FL108 - VS7 Supreme Fuel System Cleaner
Part #FL108
SECTION IV FIRE AND EXPLOSION HAZARD DATA
Flash Point: 125 F. (48.0 C.) TOC
Flammable Limits: 0.8 TO 7.0
Lower Explosive Limit (LEL): 0.8
Upper Explosive Limit (UEL): 7.0
Extinguisher Media
Use carbon dioxide, dry chemical, foam and /or water fog as extinguishing media.
Special Fire Fighting Procedures
Wear NIOSH approved SCBA respirator in the positive pressure mode and chemical protective clothing.
Unusual Fire and Explosion Hazards
Water may cause frothing.
SECTION V REACTIVITY DATA
Stable: Yes
Hazardous Polymerization May Occur: No
Conditions to Avoid
Store below 150 F. Do not apply high heat or flame to container. Keep separate from strong oxidizing
agents.
Incompatibility (Material to Avoid)
Strong oxidants.
Hazardous Decomposition or Byproducts
Excessive heating and/or incomplete combustion will produce carbon monoxide.
SECTION VI HEALTH HAZARD DATA
Effects on Eyes
Irritant.
Effects on Skin
Irritant.
Effects Due to Ingestion
Toxicity is relatively low, there is a risk of aspiration of product into the lungs. On ingestion of large
quantities, slight GI discomfort, diarrhea, headache and nervous system depression may occur. Small
doses may produce irritation and diarrhea.
Effects Due to Inhalation
Low risk of inhalation. Mists above TLV may cause chemical pneumonitis.
First Aid Procedures for Eyes
If the product contacts the eyes, immediately wash the eyes with large quantities of room temperature
water for at least 15 minutes, occasionally lifting the lower and upper lids. Get medical attention
immediately.
First Aid Procedures for Skin
If the product contacts the skin, promptly wash the contaminated skin with soap and water for at least 15
minutes. If this product penetrates the clothing, promptly remove the clothing and wash the skin with soap
and water.
First Aid Procedures for Ingestion
Do not induce vomiting, product contains petroleum distillate. Get medical attention immediately.
Page -2-
FL108 - VS7 Supreme Fuel System Cleaner
Part #FL108
SECTION VI HEALTH HAZARD DATA (cont.)
First Aid Procedures for Inhalation
Move the exposed person to fresh air at once and call emergency medical care. If breathing has stopped,
give artificial respiration. If breathing is difficult, give humidified oxygen.
SECTION VII PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to Be Taken in Case Material is Released or Spilled
SMALL SPILL: Remove sources of heat or ignition, provide adequate ventilation, contain leak using
absorbent, inert, non-combustible material.
LARGE SPILL: Contain spill, transfer to secure containers. In the event of an uncontrolled material
release, the user should determine if release is reportable under applicable laws and regulations.
Waste Disposal Method
Dispose of product in accordance with local, state, and federal regulations. Before attempting clean up,
refer to other sections of MSDS for hazard warning information.
Precautions to Be Taken in Handling and Storing
See other sections of MSDS.
Other Precautions
Product is combustible, handle accordingly.
SECTION VIII CONTROL MEASURES
Local Exhaust: Provide local ventilation to maintain exposure levels below recommended
exposure limits.
Mechanical (General): In confined spaces, mechanical ventilation may be required.
Special Ventilation: OSHA TWA=5 mg/m3.
Other Ventilation: N/A
Protective Gloves: Use oil impervious gloves as required.
Eye Protection: Use splash proof chemical, safety goggles or appropriate full-face respirator.
Other Protective Clothing or Equipment
If there is a possibility of exposure of an individual鈥檚 body to the product, wear body-covering work
clothes to avoid prolonged or repeated exposure.
Work/Hygienic Practices
Use normal hygiene practices.
Respiratory Protection (Specify Type)
Normally none is required. If high vapor or mist concentration are expected, use appropriate NIOSH
approved respirator for organic vapors and mists. Respirators must be selected based on the airborne
levels found in the workplace and must not exceed the working limits of the respirator.
SECTION IX ADDITIONAL INFORMATION
Additional Information
SHIPPING INFORMATION (CFR 49 AND IMDG):
PROPER SHIPPING NAME : Cleaning Compound, N.O.I.
DOT HAZARD CLASS : Consumer commodity, ORM-D
DOT UN NUMBER : None required
IMDG SHIPPING NAME : Dangerous Goods in Limited Quantities of Class 3.3 (Mineral Spirits),
PGIII.
Page -3-
FL108 - VS7 Supreme Fuel System Cleaner
Part #FL108
SECTION IX ADDITIONAL INFORMATION (cont.)
SARA TITLE III:
Section 302: None
Section 304: None
Section 311: None
Section 313: None
CERCLA:
Section 311 (b) (4): Requires discharges of crude oil and petroleum products in any kind or form to waters
must immediately be reported to the National Response Center at (800) 424-8802.
DISCLAIMER: Information presented herein is believed to be factual, as it has been derived from the
works and opinions of persons believed to be qualified experts. However, nothing contained in this
information is to be taken as warranty or representation for which the Gold Eagle Co. bears legal
responsibility. The user should review any recommendations in the specific context of the intended use to
determine whether they are appropriate.
Prepared by: Mike Profetto
Date: 05/14/03
While the information and recommendations set forth herein are believed to be accurate as of the MSDS date, Corbus, a
division of Compliance Management Systems, Inc., makes no warranties expressed or implied of fitness for a particular
purpose with respect hereto and disclaims all liability from reliance thereon.
Page -4-
FL110 - VS7 Foaming Throttle Plate Cleaner
Part #FL110
Gold Eagle Company
4400 S. Kildare Blvd.
Chicago, IL 60632-4372(773) 376-4400
PRODUCT NAME: MIGHTY VS7 FOAMING THROTTLE PLATE CLEANER HMIS CODES: H F R P
PRODUCT CODE: FL110 2*2 0
================== SECTION I - DISTRIBUTOR IDENTIFICATION ==================
DISTRIBUTOR'S NAME : MIGHTY DISTRIBUTING SYSTEM OF AMERICA
ADDRESS : 650 ENGINEERING DRIVE
NORCROSS, GA 30092
EMERGENCY PHONE : 770-448-3900 DATE PRINTED : 9/8/2003
INFORMATION PHONE : 770-448-3900 NAME OF PREPARER : ESP
========== SECTION II -HAZARDOUS INGREDIENTS/SARA III INFORMATION =========
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER mm Hg @ TEMP PERCENT
--------------------------------------------------------------------------------
AROMATIC HYDROCARBON 64742-94-5 .09 68 27
OSHA PEL: NOT ESTAB, ACGIH TLV: NOT ESTAB
AROMATIC PETROLEUM DISTILLATE 64742-94-5 .5 68 15
OSHA PEL: NOT ESTAB, ACGIH TLV: NOT ESTAB
* 2-BUTOXYETHANOL, GLYCOL ETHER EB 111-76-2 .6 68 8
OSHA PEL: 25 PPM, ACGIH TLV: 25 PPM, : SKIN
MORPHOLINE 110-91-8 7 68 2
OSHA PEL: 20 PPM, ACGIH TLV: 20 PPM, : SKIN
PROPANE 74-98-6 6350 68 10
OSHA PEL: 1000 PPM, ACGIH TLV: ASPHYXIANT
BUTANE 106-97-8 1640 68 10
OSHA PEL: 800 PPM, ACGIH TLV: 800 PPM
* Indicates toxic chemical(s) subject to the reporting requirements of
section 313 of Title III and of 40 CFR 372.
=============== SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ============
BOILING RANGE: -44 deg F - 450 SPECIFIC GRAVITY (H2O=1): 0.82
VAPOR DENSITY: HEAVIER THAN AIR EVAPORATION RATE: SLOWER THAN ETHER
SOLUBILITY IN WATER: NIL
APPEARANCE AND ODOR: AEROSOL PRODUCT
================= SECTION IV - FIRE AND EXPLOSION HAZARD DATA ==============
FLASH POINT: -156 deg F METHOD USED: ESTIMATED
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: .9 UPPER: 12.7
EXTINGUISHING MEDIA: FOAM, CO2, DRY CHEMICAL, WATER FOG
SPECIAL FIREFIGHTING PROCEDURES
WATER SPRAY MAY BE INEFFECTIVE. WATER MAY BE USED TO COOL CONTAINERS TO PREVENT PRESSURE
BUILD-UP AND EXPLOSION WHEN EXPOSED TO EXTREME HEAT. IF WATER IS USED,
FOG NOZZLES PREFERRED. WEAR GOGGLES AND SELF-CONTAINED BREATHING APPARATUS.
UNUSUAL FIRE AND EXPLOSION HAZARDS
CLOSED CONTAINERS MAY EXPLODE FROM INTERNAL PRESSURE BUILD-UP WHEN EXPOSED TO EXTREME HEAT
AND DISCHARGE CONTENTS. VAPOR ACCUMULATION CAN FLASH OR EXPLODE IF IGNITED. OVEREXPOSURE TO
DECOMPOSITION PRODUCTS MAY CAUSE A HEALTH HAZARD.
SYMPTOMS MAY NOT BE READILY APPARENT. OBTAIN MEDICAL ATTENTION.
FL110 - VS7 Foaming Throttle Plate Cleaner
Part #FL110
======================== SECTION V - REACTIVITY DATA =======================
STABILITY: STABLE
CONDITIONS TO AVOID
APPLICATION TO HOT SURFACES. STORAGE ABOVE 120 DEG F. EXPOSURE TO OPEN FLAME.
INCOMPATIBILITY (MATERIALS TO AVOID)
STRONG OXIDIZING AGENTS.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS
MAY PRODUCE FUMES WHEN HEATED TO DECOMPOSITION. FUMES MAY CONTAIN CARBON MONOXIDE AND OTHER
TOXIC FUMES.
HAZARDOUS POLYMERIZATION: WILL NOT OCCUR
==================== SECTION VI - HEALTH HAZARD DATA =======================
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
RESPIRATORY IRRITATION, HEADACHE, NAUSEA, FATIGUE, DROWSINESS, IMPAIRED CO-ORDINATION.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
SKIN: CONTACT MAY DRY THE SKIN; PROLONGED CONTACT MAY CAUSE MODERATE IRRITATION.
EYES: LIQUID OR VAPOR CAN CAUSE MODERATE TO SEVERE IRRITATION.
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
NOT EASILY ABSORBED. SOLVENT ACTION CAN DRY AND DEFAT THE SKIN CAUSING THE SKIN TO CRACK,
LEADING TO DERMATITIS.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
NOT A LIKELY ROUTE OF EXPOSURE. IF SWALLOWED, SEEK IMMEDIATE MEDICAL ADVICE AND/OR
ATTENTION.
HEALTH HAZARDS (ACUTE AND CHRONIC)
ACUTE: EYE IRRITANT. POSSIBLE SKIN IRRITANT. CHRONIC: NONE KNOWN.
CARCINOGENICITY: NTP CARCINOGEN: No IARC MONOGRAPHS: No OSHA REGULATED: No
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
NONE KNOWN.
EMERGENCY AND FIRST AID PROCEDURES
INHALATION: REMOVE TO FRESH AIR. ADMINISTER OXYGEN IF NEEDED. APPLY ARTIFICIAL
RESPIRATION IF BREATHING HAS STOPPED. GET MEDICAL ATTENTION. SKIN: WIPE OFF WITH TOWEL. WASH
WITH SOAP AND WATER. GET MEDICAL ATTENTION IF IRRITATION PERSISTS.
EYES: WASH IMMEDIATELY WITH LARGE VOLUMES OF FRESH WATER FOR AT LEAST 15 MINUTES. GET
MEDICAL ATTENTION.
FL110 - VS7 Foaming Throttle Plate Cleaner
Part #FL110
=========== SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE ============
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
AVOID BREATHING VAPORS. VENTILATE AREA. REMOVE ALL SOURCES OF IGNITION. CLEAN UP AREA WITH
ABSORBENT MATERIAL AND PLACE IN CLOSED CONTAINERS FOR DISPOSAL.
WASTE DISPOSAL METHOD
DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE, AND FEDERAL REGULATIONS. BEFORE ATTEMPTING CLEAN
UP, REFER TO OTHER SECTIONS OF THIS MSDS FOR HAZARD CAUTION INFORMATION.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
STORE AND USE IN COOL, DRY, WELL-VENTILATED AREAS. VAPORS MAY CAUSE FLASH FIRE.
KEEP AWAY FROM HEAT, SPARKS AND FLAME. DO NOT STORE ABOVE 120 DEG F. DO NOT
PUNCTURE OR INCINERATE (BURN) CANS. DO NOT STICK PIN, NAIL OR ANY OTHER SHARP
OBJECT INTO OPENING ON TOP OF CAN. DO NOT SPRAY IN EYES. SEE PRODUCT LABEL FOR ADDITIONAL
INFORMATION.
OTHER PRECAUTIONS
SMALL PRESSURIZED CONTAINERS OF FLAMMABLE PRODUCTS MAY BE STORED IN AREAS
SUITABLE FOR ORDINARY COMBUSTIBLES WITH RESPECT TO CONSTRUCTION, DRAINAGE,
CONTROL OF IGNITION SOURCES, AND VENTILATION EXCEPT THAT THEY SHOULD NOT BE STORED IN
BASEMENTS. STORAGE SHOULD BE IN AREAS SUITABLE FOR LEVEL 2 AEROSOLS.
===================== SECTION VIII - CONTROL MEASURES ======================
RESPIRATORY PROTECTION
AVOID BREATHING VAPORS. USE WITH ADEQUATE VENTILATION EQUAL TO OUT OF DOORS. IN
RESTRICTED AREAS, USE APPROVED CHEMICAL/ MECHANICAL FILTERS DESIGNED TO REMOVE A COMBINATION
OF PARTICLES AND VAPOR. IN CONFINED AREAS, USE APPROVED AIR LINE TYPE RESPIRATOR OR HOOD.
SELF-CONTAINED BREATHING APPARATUS IS REQUIRED FOR
VAPOR CONCENTRATIONS ABOVE PEL/TLV LIMITS.
VENTILATION
SUFFICIENT TO PREVENT INHALATION OF SOLVENT VAPORS. GENERAL DILUTION AND/OR
LOCAL EXHAUST VENTILATION IN VOLUME OR PATTERN TO KEEP PEL/TLV OF MOST HAZARDOUS INGREDIENT
BELOW ACCEPTABLE LIMIT AND LEL BELOW STATED LIMIT.
PROTECTIVE GLOVES
SOLVENT RESISTANT GLOVES REQUIRED FOR PROLONGED OR REPEATED CONTACT.
EYE PROTECTION
USE OF SAFETY GLASSES WITH SPLASH GUARDS OR FULL FACE SHIELD IS RECOMMENDED.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
USE OF SOLVENT RESISTANT APRONS OR OTHER CLOTHING IS RECOMMENDED.
WORK/HYGIENIC PRACTICES
EYE WASHES AND SAFETY SHOWERS IN THE WORKPLACE ARE RECOMMENDED.
========================= SECTION IX - DISCLAIMER ==========================
THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED ACCURATE. HOWEVER,
NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF THE DATA OR THE RESULTS TO BE
OBTAINED FROM THE USE THEREOF. BECAUSE THE INFORMATION CONTAINED
HEREIN MAY BE APPLIED UNDER CONDITIONS BEYOND OUR CONTROL, WE ASSUME NO RESPONSIBILITY FOR
ITS USE.
MATERIAL SAFETY DATA SHEET
FL112 - VS7 Top Engine Cleaner - 12 oz
Part #FL112
Gold Eagle Company
4400 S. Kildare Blvd.
Chicago, IL 60632-4372
(773) 376-4400
************************* HMIS RATINGS *************************
Health: 1 Flammability: 3 Reactivity: 0 Pers. Prot. Index: B
************************* NFPA RATINGS *************************
Health: 1 Fire: 3 Reactivity: 0 Specific Hazard: None
SECTION I PRODUCT IDENTITY
Product / Trade Name (s): FL112 - VS7 Top Engine Cleaner - 12 oz
Part Number: FL112
MSDS Date: 05/14/03
CAS #: N/A
Category: N/A
Distributor: N/A
Chemical Name: N/A
Formula: N/A
Brief Description: Carb and Choke solvent cleaner.
SECTION II HAZARDOUS INGREDIENTS & EXPOSURE LIMITS
CHEMICAL NAME CAS # % LIMIT VALUES
DIACETONE ALCOHOL 123-42-2 10.00 PEL 50 ppm
PEL 240 mg/m3
ISOPROPANOL 67-63-0 30.00 PEL 400 ppm
PEL 980 mg/m3
XYLENE 1330-20-7 60.00 PEL 100 ppm
PEL 435 mg/m3
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point: 160 F. (71.1 C.)
Vapor Pressure (mm Hg.): N/A
Vapor Density (AIR = 1): >1.0
Solubility in Water: Partial
% Volatile / Volume: 100.0
Appearance and Odor: Water white liquid, solvent odor
pH: N/A
Specific Gravity (H2O = 1): 0.860
Page -1-
FL112 - VS7 Top Engine Cleaner - 12 oz
Part #FL112
SECTION III PHYSICAL/CHEMICAL CHARACTERISTICS (cont.)
Miscellaneous Information:
Product is flammable, keep away from sources of ignition, combustibles, oxidizing materials and acid.
Store in an area equipped with automatic sprinklers or fire extinguishing system. Empty containers
contain product residues, assume emptied containers to have same hazards as full containers.
SECTION IV FIRE AND EXPLOSION HAZARD DATA
Flash Point: 54 F. (12.2 C.) TOC
Flammable Limits: 1.0 TO 7.0
Lower Explosive Limit (LEL): 1.0
Upper Explosive Limit (UEL): 7.0
Extinguisher Media
Use halon replacement or carbon dioxide extinguishers or alcohol foam for small fires. Water spray or fog
can cool fire but may not be effective in extinguishing fire. Large fires should be extinguished with alcohol
foam. Use water spray to cool containers exposed to fire. Containers may explode in heat or fire.
Special Fire Fighting Procedures
Wear NIOSH approved SCBA respirator in the positive pressure mode and chemical protective clothing.
Unusual Fire and Explosion Hazards
Dangerous fire and explosion hazard when exposed to heat or flame. Isopropanol is extremely flammable
and forms explosive mixtures with air. Isopropanol vapors may travel considerable distance to a source of
ignition and flash back.
SECTION V REACTIVITY DATA
Stable: Yes
Hazardous Polymerization May Occur: No
Conditions to Avoid
Store in a well ventilated place away from sources of ignition, combustibles, oxidizing materials and acid.
Incompatibility (Material to Avoid)
Strong oxidizing agents, amines, chlorinated compounds and caustic materials.
Hazardous Decomposition or Byproducts
Excessive heating and/or incomplete combustion will produce carbon monoxide.
SECTION VI HEALTH HAZARD DATA
Effects on Eyes
Irritant.
Effects on Skin
Prolonged or repeated skin contact may cause dermatitis, scaling and possible systemic effects.
Effects Due to Ingestion
Low level of toxicity, small amounts of liquid aspirated into the respiratory system during ingestion may
cause pulmonary edema.
Effects Due to Inhalation
Narcotic chemical affecting central nervous system resulting in: dizziness, nausea, visual impairment,
narcosis and muscular impairment.
Page -2-
FL112 - VS7 Top Engine Cleaner - 12 oz
Part #FL112
SECTION VI HEALTH HAZARD DATA (cont.)
First Aid Procedures for Eyes
If the product contacts the eyes, immediately wash the eyes with large quantities of room temperature
water for at least 15 minutes, occasionally lifting the lower and upper lids. Get medical attention
immediately. A follow up visit to an opthalmologist should be made. Contact lenses should not be worn
when working with this chemical.
First Aid Procedures for Skin
If the product contacts the skin, promptly wash the contaminated skin with soap and water for at least 15
minutes. If this product penetrates the clothing, promptly remove the clothing and wash the skin with soap
and water. Systemic effects may be delayed 18 to 72 hours, therefore keep individual under observation.
First Aid Procedures for Ingestion
If this product is ingested. DO NOT INDUCE A PERSON TO VOMIT. Get medical attention
immediately.
First Aid Procedures for Inhalation
Move the exposed person to fresh air at once and call emergency medical care. If breathing has stopped,
give artificial respiration. If breathing is difficult, give humidified oxygen.
SECTION VII PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to Be Taken in Case Material is Released or Spilled
SMALL SPILL: Remove sources of heat or ignition, provide adequate ventilation, contain leak using
absorbent, inert, non-combustible material.
LARGE SPILL: Contain spill, transfer to secure containers. In the event of an uncontrolled material
release, the user should determine if release is reportable under applicable laws and regulations.
Waste Disposal Method
Dispose of product in accordance with local, state, and federal regulations. Before attempting clean up,
refer to other sections of MSDS for hazard warning information.
Precautions to Be Taken in Handling and Storing
See other sections of MSDS.
Other Precautions
Product is flammable, handle accordingly.
SECTION VIII CONTROL MEASURES
Local Exhaust: Provide local ventilation to maintain exposure levels below recommended
exposure limits.
Mechanical (General): In confined spaces, mechanical ventilation may be required.
Special Ventilation: N/A
Other Ventilation: N/A
Protective Gloves: Use natural rubber or neoprene gloves as required.
Eye Protection: Use splash proof chemical, safety goggles or appropriate full-face respirator.
Contact lenses should not be worn when working with this chemical.
Other Protective Clothing or Equipment
If there is a possibility of exposure of an individual鈥檚 body to the product, wear body-covering work
clothes to avoid prolonged or repeated exposure.
Work/Hygienic Practices
Use normal hygiene practices.
Page -3-
FL112 - VS7 Top Engine Cleaner - 12 oz
Part #FL112
SECTION VIII CONTROL MEASURES (cont.)
Respiratory Protection (Specify Type)
Do not use air purifying respirator. Use appropriate NIOSH approved supplied or self contained
respirator. Respirators must be selected based on the airborne levels found in the workplace and must not
exceed the working limits of the respirator.
SECTION IX ADDITIONAL INFORMATION
Additional Information
SHIPPING INFORMATION (CFR 49 AND IMDG):
PROPER SHIPPING NAME : Cleaning compound, N.O.I.
DOT HAZARD CLASS : Compounds, Gum Removing
(N.O.S.), Flammable Liquids, UN1993,
PGII, (Xylene, Isopropanol, Diacetone
Alcohol).
DOT UN NUMBER : None required.
IMDG SHIPPING NAME : Flammable Liquids, N.O.S., 3.2, UN1993
PGII (Xylene, Isopropanol, Diacetone
Alcohol), EmS#: 3-07.
SARA TITLE III:
Section 302: Xylene, 1330-20-7, RQ-1000 lbs.
Section 304: None
Section 311: Hazard categories-Fire Hazard=Yes; Acute=Yes and
Chronic=Yes.
Section 313: Xylene, 1330-20-7, 60%-70%.
CERCLA:
Section 311 (b) (4) : Requires discharges of crude oil and petroleum products in any kind or form to waters
must immediately be reported to the National Response Center at (800) 424-8802.
DISCLAIMER: Information presented herein is believed to be factual, as it has been derived from the
works and opinions of persons believed to be qualified experts. However, nothing contained in this
information is to be taken as warranty or representation for which the Gold Eagle Co. bears legal
responsibility. The user should review any recommendations in the specific context of the intended use to
determine whether they are appropriate.
Prepared by: Mike Profetto
Date: 05/14/03
While the information and recommendations set forth herein are believed to be accurate as of the MSDS date, Corbus, a
division of Compliance Management Systems, Inc., makes no warranties expressed or implied of fitness for a particular
purpose with respect hereto and disclaims all liability from reliance thereon.
Page -4-
|