MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 1 of 8
USG ACRI-ADD鈩?
USG ACRI ADD 16570001v6
SECTION 1
CHEMICAL PRODUCT AND IDENTIFICATION
CGC Inc.
Product Safety: 1 (800) 507-8899
350 Burnhamthorpe Rd. W., 5th Floor
www.cgcinc.com
Mississauga, Ontario L5B 3J1
Version Date: January 1, 2008
(905) 803-5600 Fax (905) 803-5688
Version: 6
A Subsidiary of USG Corporation
PRODUCT(S) USG ACRI-ADD鈩?
CHEMICAL FAMILY /
Acrylic Add-Mix Fortifier
GENERAL CATEGORY
SYNONYMS Fortifier
SECTION 2
HAZARD IDENTIFICATION
EMERGENCY OVERVIEW:
螖WARNING!
This product is not expected to produce any unusual hazards during normal use. Exposure to high dust, mist or vapor
levels may irritate the skin, eyes, nose, throat, or upper respiratory tract.
POTENTIAL HEALTH EFFECTS (See Section 11 for more information)
ACUTE :
Exposure to dust, mist or vapors generated during the handling, spray application or use of the product
may irritate eyes, skin, nose, throat, and upper respiratory tract. Persons subjected to large amounts of
this dust, mist or vapor will be forced to leave area because of nuisance conditions such as coughing,
sneezing and nasal irritation. Labored breathing may occur after excessive inhalation. If respiratory
symptoms persist, consult physician. Breathing of acrylic polymer vapors can cause slight headache,
Inhalation
dizziness, nausea, drowsiness, and/or stupor. Exposure to high vapor levels may irritate the nose,
throat, or upper respiratory tract. Labored breathing may occur after excessive inhalation. If respiratory
symptoms persist, consult physician. Breathing of butyl benzyl phthalate vapors can cause slight
headache, dizziness, nausea, drowsiness, and/or stupor.
Dust/mist/vapors can cause mechanical irritation of eyes. If burning, redness, itching, pain or other
Eyes symptoms persist or develop, consult physician. Acrylic polymer vapors may cause slight temporary
eye irritation. Butyl benzyl phthalate vapors may cause slight temporary eye irritation.
Skin None known.
Ingestion None known.
CHRONIC:
Inhalation Prolonged and repeated exposure to butyl benzyl phthalate may cause nervous system damage.
Eyes None known.
Skin None known.
Ingestion None known.
TARGET ORGANS: Eyes, skin and respiratory system.
MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 2 of 8
USG ACRI-ADD鈩?
PRIMARY ROUTES OF ENTRY: Inhalation, eyes and skin contact.
CARCINOGENICITY CLASSIFICATION OF INGREDIENT(S) All substances listed are associated with the nature of
the raw materials used in the manufacture of this product and are not independent components of the product
formulation. All substances, if present, are at levels well below regulatory limits. See Section 11: Toxicology
Information for detailed information.
MATERIAL IARC NTP ACGIH CAL- 65
Acetaldehyde 2B 2 A3 Listed
Formaldehyde 1 2 A2 Listed
IARC - International Agency for Research on Cancer: 1- Carcinogenic to humans; 2A 鈥? Probably carcinogenic to
humans; 2B 鈥? Possibly carcinogenic to humans; 3 - Not classifiable as a carcinogen; 4 鈥? Probably not a carcinogen
NTP 鈥? National Toxicology Program (Health and Human Services Dept., Public Health Service, NIH/NIEHS): 1-
Known to be carcinogen; 2- Anticipated to be carcinogens
ACGIH 鈥? American Conference of Governmental Industrial Hygienists: A1 鈥? Confirmed human carcinogen; A2 鈥?
Suspected human carcinogen; A3 鈥? Animal carcinogen; A4 - Not classifiable as a carcinogen; A5 鈥? Not suspected as
a human carcinogen
CAL-65 鈥? California Proposition 65 鈥淐hemicals known to the State of California to Cause Cancer鈥?
POTENTIAL ENVIRONMENTAL EFFECTS: A component of this product, butyl benzyl pthalate meets the definition of
a marine pollutant. (See Section 12 for more information)
SECTION 3
COMPOSITION, INFORMATION ON INGREDIENTS
MATERIAL WT% CAS #
Water >70 7732-18-5
Acrylic Polymer <30 Proprietary
Butyl Benzyl Phthalate <1 85-68-7
All ingredients of this product are included in the U.S. Environmental Protection Agency鈥檚 Toxic Substances Control
Act Chemical Substance Inventory and the Canadian Domestic Substances List (DSL).
SECTION 4
FIRST AID MEASURES
FIRST AID PROCEDURES
Remove to fresh air. Leave the area of exposure and remain away until coughing and other symptoms
Inhalation
subside. Other measures are usually not necessary, however if conditions warrant, contact physician.
In case of contact, do not rub or scratch your eyes. To prevent mechanical irritation, flush thoroughly
Eyes
with water for 15 minutes. If irritation persists, consult physician.
Skin Wash with mild soap and water. If irritation persists, consult physician.
Never give anything by mouth to an unconscious person. If swallowed, do not induce vomiting. Give
Ingestion large quantities of water, or if available several glasses of milk. If vomiting occurs spontaneously, keep
airway passage clear and give more water. Seek medical attention immediately.
MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 3 of 8
USG ACRI-ADD鈩?
MEDICAL CONDITIONS WHICH MAY BE AGGRAVATED: Pre-existing upper respiratory and lung diseases such
as, but not limited to, bronchitis, emphysema and asthma. Pre-existing skin diseases such as, but not limited to,
rashes and dermatitis.
NOTES TO PHYSICIAN: Treatment should be directed at the control of symptoms and the clinical condition.
SECTION 5
FIRE FIGHTING MEASURES
General Fire Hazards None known
Extinguishing Media Water or use extinguishing media appropriate for surrounding fire.
Special Fire Fighting Procedures Wear appropriate personal protective equipment. See section 8.
Unusual Fire and Explosion
None known
Hazards
Hazardous Combustion Products None known
Flash Point Auto Ignition
Not Determined Not Applicable
Method Used Not Applicable Flammability
Not Applicable
Classification
Upper Flammable Limit (UFL) Not Determined
Lower Flammable Limit (LFL) Rate of Burning
Not Determined Not Applicable
SECTION 6
ACCIDENTAL RELEASE MEASURES
CONTAINMENT: No special precautions. Wear appropriate personal protective equipment. See section 8.
CLEAN-UP: Use normal clean up procedures. No special precautions.
DISPOSAL: Follow all local, state, provincial and federal regulations. Never discharge large releases directly into
sewers or surface waters.
SECTION 7
HANDLING AND STORAGE
HANDLING: Avoid dust/mist/vapor contact with eyes. Wear the appropriate eye protection against dust/mist/vapor
(See Section 8). Minimize dust/mist/vapor generation and accumulation. Avoid breathing dust/mist/vapors. Wear the
appropriate respiratory protection against dust/mist/vapor in poorly ventilated areas and if TLV is exceeded (see
Sections 2 and 8). Use good safety and industrial hygiene practices. Avoid contact with skin and eyes. Wear gloves
and protective clothing to prevent repeated or prolonged skin contact.
STORAGE: Store in a cool, dry, ventilated area away from sources of heat, moisture and incompatibilities (see
Section 10). Store at 60-95 潞F (15-35 潞C). Do not use if material has spoiled, i.e., there is a moldy appearance or an
unpleasant odor. Close container and discard properly. Keep tightly sealed following use.
MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 4 of 8
USG ACRI-ADD鈩?
SECTION 8
EXPOSURE CONTROLS/PERSONAL PROTECTION
TLV (mg/m3) PEL( mg/m3)
MATERIAL WT%
Water >70 (NE) (NE)
Acrylic Polymer <30 (NE) (NE)
Butyl Benzyl Phthalate <1 (NE) (NE)
(T)鈥揟otal; (R)鈥揜espirable; (NE)-Not Established; (C)-Ceiling; (STEL)-Short-term exposure limit
(F)-Fume; (Du)-Dust; (M)-Mist
ppm-part per million; f/cc-fiber per cubic centimeter; mppcf- million particles per cubic foot
ENGINEERING CONTROLS: Provide ventilation sufficient to control airborne dust/mist/vapor levels. If user
operations generate airborne dust/mist/vapor, use ventilation to keep dust concentrations below permissible exposure
limits. Where general ventilation is inadequate, use process enclosures, local exhaust ventilation, or other
engineering controls to control dust/mist/vapor levels below permissible exposure limits. Provide ventilation sufficient
to control vapor exposures. Where general ventilation is inadequate, use process enclosures, local exhaust
ventilation, or other engineering controls to control vapor levels. If engineering controls are not possible, wear a
properly fitted NIOSH/MSHA-approved vapor respirator. Wear a NIOSH/MSHA-approved respirator equipped with
vapor cartridges when in poorly ventilated areas, and if TLV is exceeded. A respiratory program that meets OSHA's
29 CFR 1910.134 and ANSI Z88.2 requirements must be followed whenever workplace conditions warrant a
respirator's use.
RESPIRATORY PROTECTION: Wear a NIOSH/MSHA-approved respirator equipped with particulate cartridges when
dusty or misty in poorly ventilated areas, and if TLV is exceeded. A respiratory program that meets OSHA's 29 CFR
1910.134 and ANSI Z88.2 requirements must be followed whenever workplace conditions warrant a respirator's use.
If engineering controls are not possible, wear a properly fitted NIOSH/MSHA-approved particulate respirator.
OTHER PERSONAL PROTECTIVE EQUIPMENT:
Eye/Face Wear eye protection, safety glasses or goggles, to avoid possible eye contact.
Skin Wear gloves and protective clothing to prevent repeated or prolonged skin contact.
Selection of Personal Protective Equipment will depend on environmental working conditions and
General
operations.
SECTION 9
PHYSICAL AND CHEMICAL PROPERTIES
Appearance Vapor Density (Air = 1)
Gray to off white < 1(same as water)
Odor Specific Gravity (H2O = 1)
Slight acrylic odor ~1.0-1.2
Aquesous acrylic
Odor Threshold Solubility in water (g/100g)
Not Determined
emulsion
Physical State Partition Coefficient
Paste Not Determined
pH @ 25 潞 C Auto-ignition Temp
~8.5 - 9.5 Not Determined
Melting Point Decomposition Temp
Not Applicable Not Determined
Freezing Point Viscosity
32潞F/ 0潞C Not Determined
MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 5 of 8
USG ACRI-ADD鈩?
Boiling Point Particle Size
212潞F/ 100潞C Not Determined
Flash Point Bulk Density
Not Determined 7.8 - 8.5 lbs/gal
< 1(same as
Evaporation Rate (BuAc = 1) Molecular Weight Mixture
water)
Upper Flammable Limit (UFL) VOC Content
Not Determined Not Determined
Lower Flammable Limit (LFL) Percent Volatile
Not Determined Not Determined
Vapor Pressure (mm Hg) ~24 mmHg@ 25潞C
SECTION 10
CHEMICAL STABILITY AND REACTIVITY
STABILITY Stable.
CONDITIONS TO AVOID Contact with incompatibles (see below).
INCOMPATIBILITY None known.
HAZARDOUS POLYMERIZATION None known.
Thermal decomposition may yield acrylic monomers, carbon dioxide
HAZARDOUS DECOMPOSITION
and carbon monoxide.
SECTION 11
TOXICOLOGICAL INFORMATION
ACUTE EFFECTS: None known.
CHRONIC EFFECTS / CARCINOGENICITY:
Acetaldehyde/formaldehyde: A component of this product is a proprietary acrylic polymer. The acrylic polymer is not
classified as a carcinogen by IARC, NTP or ACGIH. However, trace amounts acetaldehyde and formaldehyde may be
associated with the the emulsion polymer. Any exposure to these substances formaldehyde is expected to remain
well below OSHA regulatory and ACGIH recommended limits during normal handling and use of this product.
SECTION 12
ECOLOGICAL INFORMATION
ENVIRONMENTAL TOXICITY: A component of this product, butyl benzyl pthalate meets the definition of a marine
pollutant.
Ecotoxicity value Not determined.
SECTION 13
DISPOSAL CONSIDERATIONS
MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 6 of 8
USG ACRI-ADD鈩?
WASTE DISPOSAL METHOD: Dispose of material in accordance with federal, state, and local regulations. Never
discharge directly into sewers or surface waters. Consult with environmental regulatory agencies for guidance on
acceptable disposal practices.
SECTION 14
TRANSPORT INFORMATION
U.S. DOT INFORMATION: Not a hazardous material per DOT shipping requirements. Not classified or regulated.
Shipping Name Same as product name.
Hazard Class Not classified.
UN/NA # None. Not classified.
Packing Group None.
Label (s) Required Not applicable.
GGVSec/MDG-Code Not classified.
ICAO/IATA-DGR Not applicable.
RID/ADR None.
ADNR None.
SECTION 15
REGULATORY INFORMATION
UNITED STATES REGULATIONS
All ingredients of this product are included in the U.S. Environmental Protection Agency鈥檚 Toxic Substances Control
Act Chemical Substance Inventory.
CERCLA
Sec. 112
3 3 3
RCRA
MATERIAL WT% 0 0 1
Code
CAA
2 4 3
Water >70 NL NL NL NL NL NL
Acrylic Polymer <30 NL NL NL NL NL NL
Butyl Benzyl Phthalate <1 NL NL NL 100 NL NL
Key : NL = Not Listed
SARA Title III Section 302 (EPCRA) Extremely Hazardous Substances: Threshold Planning Quantity (TPQ)
SARA Title III Section 304 (EPCRA) Extremely Hazardous Substances: Reportable Quantity (RQ)
SARA Title III Section 313 (EPCRA) Toxic Chemicals: X= Subject to reporting under section 313
CERCLA Hazardous Substances: Reportable Quantity (RQ)
CAA Section 112 (r) Regulated Chemicals for Accidental Release Prevention: Threshold Quantities(TQ)
RCRA Hazardous Waste: RCRA hazardous waste code
CANADIAN REGULATIONS
MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 7 of 8
USG ACRI-ADD鈩?
This product has been classified in accordance with the hazard criteria of Controlled Product regulations and the
MSDS contains all the information required by the Controlled Products Regulations. All ingredients of this product are
included in the Canadian Domestic Substances List (DSL).
WHMIS
MATERIAL WT% IDL Item #
Classification
Water >70 Not Listed Not Listed
Acrylic Polymer <30 Not Listed Not Listed
Butyl Benzyl Phthalate <1 241 Not Listed
IDL Item#: Canadian Hazardous Products Act 鈥? Ingredient Disclosure List Item #
WHMIS Classification: Workplace Hazardous Material Information System
Risk and Safety Phrases defined by European Union Directive 67/548/EEC (Annex III and IV)
R-Phrase(s): R36/37/38
S-Phrase(s): S2
SECTION 16
OTHER INFORMATION
Label Information
螖 WARNING!
Vapors and/or dust may cause irritation to eyes, skin, nose, throat and upper respiratory tract. Avoid irritation by
reducing exposures to vapors, dust and direct contact. Use in a well-ventilated area or provide sufficient local
ventilation. If vapor levels are high or if dusty, wear a NIOSH/MSHA-approved vapor or dust respirator. Wear eye
protection and protective impervious gloves. If eye contact occurs, flush thoroughly with water for 15 minutes. If
irritation persists, call physician. Wash with soap and water after use. Do not ingest. If ingested, call physician. Do
not use if material has spoiled, i.e., there is a moldy appearance or an unpleasant odor. Close container and discard
properly. Product safety information: (800) 507-8899 or www.cgcinc.com.
KEEP OUT OF REACH OF CHILDREN.
INFORMATION FOR HANDLING AND IDENTIFICATION OF CHEMICAL HAZARDS
0 = Minimal Hazard
*
HEALTH 1
0
NFPA Ratings: HIMS Ratings: 1 = Slight Hazard
0
FLAMMABILITY
1 0
Health: 1 Health: 1 2 = Moderate Hazard
0
PHYSICAL HAZARD
Fire: 0 Fire: 0 3 = Serious Hazard
B
PERSONAL PROTECTION
Reactivity: 0 Reactivity: 0 4 = Severe Hazard
B - Safety glasses and gloves
Key/Legend
TLV Threshold Limit Value
PEL Permissible Exposure Limit
CAS Chemical Abstracts Service (Registry Number)
NIOSH National Institute for Occupational Safety and Health
MSHA Mine Safety and Health Administration
MATERIAL SAFETY DATA SHEET MSDS #16-570-001
Page 8 of 8
USG ACRI-ADD鈩?
OSHA Occupational Health and Safety Administration
ACGIH American Conference of Governmental Industrial Hygienists
IARC International Agency for Research on Cancer
DOT United States Department of Transportation
EPA United States Environmental Protection Agency
NFPA National Fire Protection Association
HMIS Hazardous Materials Identification System
PPE Personal Protection Equipment
TSCA Toxic Substances Control Act
DSL Canadian Domestic Substances List
NDSL Canadian Non-Domestic Substances List
SARA Superfund Amendments and Reauthorization Act of 1986
CAA Clean Air Act
Emergency Planning & Community Right-to-know Act
EPCRA
RCRA Resource Conservation and Recovery Act
CERCLA Comprehensive Environmental Response, Compensation and Liability Act of 1980
UN/NA# United Nations/North America number
CFR Code of Federal Regulations
WHMIS Workplace Hazardous Material Information System
Prepared by:
Product Safety
USG Corporation
550 West Adams Street
Chicago, IL 60661-3637
The information contained in this document applies to this specific material as supplied. It may not be valid for this
material if it is used in combination with any other materials. It is the user鈥檚 responsibility to satisfy oneself as to the
suitability and completeness of this information for his/her own particular use.
END
|