MATERIAL SAFETY DATA SHEET 02370 Pg. 1
1. Chemical Product and Contact Information Issued: 11/19/07
Product Name: Abrasive Cloth Belts, Part Numbers:
Aluminum Oxide 810-021
810-022
LECO Corporation 810-023
810-024
3000 Lakeview
810-025
St. Joseph, Michigan 49085
810-026
Information: 269-983-5531
Chemtrec: 800-424-9300
(Chemtrec Int'l: 703-527-3887)
2. Composition/Information on Ingredients
OSHA ACGIH Typical %
Component CAS No. PEL(mg/m3) TLV (mg/m3) by Weight
Vulcanized Fiber Not estab. Not estab. Not estab. 10-35
Aluminum Oxide 1344-28-1 15 10 5-15
Cured Phenolic Resins Not estab. Not estab. Not estab. 20-50
3. Hazard Identification
EMERGENCY OVERVIEW
No unusual fire or spill hazard; treat as nuisance dust generator.
Potential Health Effects
EYES: May be irritating.
SKIN: May produce irritation by abrasion.
INHALATION: Choking sensation if allowed to become very dusty.
INGESTION: Not available.
MEDICAL CONDITIONS AGGRAVATED: Persons with chronic respiratory or dermatological
disorders may be at increased risk from exposure.
CHRONIC OVEREXPOSURE: Prolonged exposure may affect lung function.
ACUTE OVEREXPOSURE: Not available.
CARCINOGENICITY: None.
P/N: 810-021
MATERIAL SAFETY DATA SHEET 02370 Pg. 2
4. First Aid Measures
EYES: Rinse with copious amounts of water for at least 15 minutes.
SKIN: Wash exposed area with soap and large amounts of water for at least 15 minutes.
INHALATION: Remove victim to fresh air. If not breathing, administer CPR. If breathing with
difficulty, give oxygen.
INGESTION: Give water and get medical advice.
5. Fire Fighting Measures
FLAMMABLE PROPERTIES: Non-flammable.
Flash Point: Not available. Method Used: Not available.
Flammable Limits (% by Volume in Air):
Lower: None. Upper: None.
AUTO-IGNITION TEMPERATURE: Not available.
HAZARDOUS COMBUSTION PRODUCTS: Not available.
EXTINGUISHING MEDIA: Water, carbon dioxide, foam, dry chemical.
FIREFIGHTING INSTRUCTIONS: Not available.
6. Accidental Release Measures
SMALL/LARGE SPILL: No special procedures.
7. Handling and Storage
HANDLING: Normal precautions should be taken for nuisance dusts and particulates generated
during grinding operation principally from work piece.
STORAGE: Keep container closed.
8. Exposure Controls/Personal Protection
ENGINEERING CONTROLS: Normal dust procedures.
RESPIRATORY PROTECTION: Avoid breathing dust.
SKIN AND HAND PROTECTION: Protective gloves recommended when grinding.
EYE AND FACE PROTECTION: Face shield or safety goggles when grinding.
OTHER PROTECTIVE EQUIPMENT: Not available.
P/N: 810-021
MATERIAL SAFETY DATA SHEET 02370 Pg. 3
9. Physical and Chemical Properties
APPEARANCE: Abrasive cloth belt.
BOILING POINT: Not available.
FREEZE-MELT POINT: Not available.
VAPOR PRESSURE (mm): Not available.
VAPOR DENSITY (air = 1): Not available.
SOLUBILITY IN WATER: Not available.
SPECIFIC GRAVITY: Not available.
pH: Not available.
ODOR: None.
PERCENT VOLATILES: Not available.
EVAPORATION RATE (Butyl Acetate = 1): Not available.
10. Stability and Reactivity
CHEMICAL STABILITY: Stable.
INCOMPATIBILITY: Not available.
HAZARDOUS DECOMPOSITION PRODUCTS: Not available.
HAZARDOUS POLYMERIZATION: None.
11. Toxicological Information
None reported.
12. Ecological Information
Not available.
13. Disposal Consideration
No special procedures.
14. Transportation Information
U.S.A. DOT: Not regulated.
P/N: 810-021
MATERIAL SAFETY DATA SHEET 02370 Pg. 4
15. Regulatory Information
U.S. FEDERAL REGULATIONS:
TSCA STATUS: On Toxic Substance Control Inventory.
CERCLA REPORTABLE QUANTITY: None.
SARA TITLE III:
Section 302 Extremely Hazardous Substances: None.
Section 311/312 Hazardous Categories: Acute, Chronic.
Section 313 Toxic Chemicals: Aluminum Oxide
(Fibrous Forms only)
RCRA STATUS: Not regulated.
CANADIAN REGULATIONS:
WHMIS: Not regulated
16. Other Information
Prepared By:
Jason Whitt
Information herein is given in good faith as authoritative and valid; however, no warranty, expressed
or implied can be made.
P/N: 810-021
|