MATERIAL SAFETY DATA SHEET
SECTION I 鈥? Product/Company Identification
FLUOROCORE庐 Fluoride-Releasing Dual-Cure Core Build-Up System
1.1 Product Trade Name:
FLUOROCORE庐 Catalyst and FLUOROCORE庐 LV Catalyst
1.2 Part (Item) Number: 612300 鈥? 621399 ALL PACKAGE CONFIGURATIONS
1.3 Division Name: DENTSPLY Caulk
1.4 Address: 38 West Clarke Avenue
City State Zip: Milford DE 19963-0359
Internet Address: http://www.caulk.com
1.5 Emergency Telephone Number: (800) 424-9300 (Chemtrec)
1.6 Telephone Number for Information:(302) 422-4511 (8:00 AM 鈥? 4:30 PM Eastern Time)
1.7 Date Prepared: 1/30/98 Date Revised 1/26/01
SECTION II 鈥? Hazardous Ingredients/Identity Information
Hazardous Components OSHA PEL ACGIH TLV CAS # Percent
Urethane Dimethacrylate Resin N. E. N. E. 105883-40-7 >70 %
Barium boron fluoroalumino silicate glass N. E. N. E. 65997-18-4 <25 %
10 mg/m3 10 mg/m3 1344-28-1
Aluminum Oxide <5%
5 mg/m3 5 mg/m3
Benzoyl Peroxide 94-36-0 <1%
SECTION III 鈥? Physical/Chemical Characteristics
3.6 Specific Gravity: 2.0 g/cm3 (L.V. 1.7 g/cm3)
3.1 Boiling point: N.A.
3.2 Vapor pressure: N.A. 3.7 Melting Point: N.E.
3.3 Vapor density: N.A. 3.8 Evaporation rate: N.A.
3.4 Solubility in water: Not Soluble
3.5 Appearance and odor: Off-white paste with sweet acrylic odor
SECTION IV - Fire and Explosion Hazard Data
4.1 Flash point (method used): N.A.
4.2 Flammability (explosive limits): LEL: N. E. UEL: N. E.
4.3 Extinguishing media: Water spray, carbon dioxide, and foam, or dry chemical.
4.4 Special fire fighting procedures: Fire fighter should wear full protective clothing including a self-contained breathing
apparatus.
4.5 Unusual fire and explosion hazards: During a fire, irritating gasses from the decomposition of the resin may be present.
SECTION V 鈥? Reactivity Data
5.1 Stability: Unstable: Stable: X
5.2 Conditions to avoid (stability): Elevated temperatures greater than 50掳C(122掳F).
5.3 Incompatibility (materials to avoid): Amines
5.4 Hazardous decomposition or byproducts: Irritating gases, CO and CO2
5.5 Hazardous polymerization: May occur: Will not occur: X
5.6 Conditions to avoid (polymerization): Heat greater than 50掳C(122掳F).
SECTION VI - Health Hazard Data
6.1 Route(s) of entry: Inhalation?: No Skin?: Yes Ingestion?: Yes
6.2 Health hazards (acute and chronic): Avoid contact with eyes and skin. Contact with eyes and skin may cause irritation.
Susceptible persons with known allergies or sensitivity to methacrylates and acrylates
may show allergic contact dermatitis and develop allergic response.
Eyes: Material can cause irritation. Skin: Material may be an irritant.
6.3 Carcinogenicity: NTP?: Not listed IARC monographs?: Not listed OSHA regulated?: No
All components of this product are in compliance with the inventory listing requirements
of the U.S. Toxic Substances Control Act (TSCA) Chemical Substance Inventory.
6.4 Signs and symptoms of exposure: Dermal redness or irritation. Severe allergic response may result in breathing difficulties.
Eye contact: irritation and possible corneal damage. Skin contact: irritation or possible
allergic response.
6.5 Medical conditions generally
aggravated by exposure: Open sores and wounds of the skin. Individuals with known sensitivity to methacrylates
or urethane dimethacrylates.
6.6 Emergency first aid procedures: Eyes: In case of eye contact, flush with flowing water for 15 minutes. Get prompt
medical attention. Skin: Wash skin with mild soap and water. If irritation persists, call
physician. Ingestion: If swallowed give 2 glasses of water to drink. See a physician.
SECTION VII - Precautions for Safe Handling and Use
7.1 Steps to be taken in case material is
released or spilled: Spread vermiculite on paste to absorb any resin. Scoop up and place in an appropriately
marked container. Avoid gross skin contact to minimize the possibility of contact
dermatitis to susceptible persons.
7.2 Waste disposal methods: Dispose of in accordance with Federal, State and Local environmental control regulations.
7.3 Precautions to be taken in handling
and storage: Store away from food and beverages. Store away from extreme heat.
7.4 Other precautions: Observe normal warehouse handling procedures. Handling of this product should be by
trained dental healthcare professionals only.
SECTION VIII - Control Measures / Personal Protection
8.1 Respiratory protection: None required during normal use of this product.
8.2 Ventilation: None required during normal intended use of this product. Local exhaust can be
used to keep vapors below threshold level.
8.3 Protective gloves: Rubber gloves.
8.4 Eye protection: Protective goggles.
8.5 Other protective clothing or equipment: Rubber apron.
8.6 Work/Hygienic practices: Observe normal care when working with chemicals. Handling of this product
should be by trained dental healthcare professionals only.
NFPA HAZARD
CLASSIFICATIONS
Health 0 NFPA 鈥? National Fire Protection Association
Flammability 1 N.A. 鈥? Not Applicable
Reactivity 0 N.E. 鈥? Not Established
Specific Hazard N. A.
512499(R-1/26/01)
MATERIAL SAFETY DATA SHEET
SECTION I - Product/Company Information
FLUOROCORE庐 Fluoride-Releasing Dual-Cure Core Build-Up System
1.1 Product Trade Name:
FLUOROCORE庐 Base Paste
1.2 Part (Item) Number: 612300 鈥? 621399 ALL PACKAGE CONFIGURATIONS
1.3 Division Name: DENTSPLY Caulk
1.4 Address: 38 West Clarke Avenue
City State Zip: Milford DE 19963-0359
Internet Address: http://www.caulk.com
1.5 Emergency Telephone Number: (800) 424-9300 (Chemtrec)
1.6 Telephone Number for Information:(302) 422-4511 (8:00 AM 鈥? 4:30 PM Eastern Time)
1.7 Date Prepared: 1/30/98 Date Revised 1/26/01
SECTION II - Hazardous Ingredients/Identity Information
Hazardous Components OSHA PEL ACGIH TLV CAS # Percent
Urethane Dimethacrylate Resin N. E. N. E. 105883-40-7 70 鈥? 75 %
Barium boron fluoroalumino silicate glass N. E. N. E. 65997-18-4 20 鈥? 25 %
SECTION III - Physical/Chemical Characteristics
2.0 g/cm3
3.1 Boiling point N.A. 3.6 Specific Gravity
3.2 Vapor pressure N.A. 3.7 Melting Point N.E.
3.3 Vapor density N.A. 3.8 Evaporation rate N.A.
3.4 Solubility in water Not Soluble
3.5 Appearance and odor:Off-white or blue paste with sweet acrylic odor
SECTION IV - Fire and Explosion Hazard Data
4.1 Flash point (method used): N.A.
4.2 Flammability (explosive limits): LEL: N. E. UEL: N. E.
4.3 Extinguishing media: Water spray, carbon dioxide, and foam, or dry chemical.
4.4 Special fire fighting procedures: Fire fighter should wear full protective clothing including a self-contained breathing
apparatus.
4.5 Unusual fire and explosion hazards: During a fire, irritating gasses from the decomposition of the resin may be present.
SECTION V - Reactivity Data
5.1 Stability: Unstable: Stable: X
5.2 Conditions to avoid (stability): Bright visible lights on paste. Elevated temperatures greater than
60掳C(140掳F).
5.3 Incompatibility (materials to avoid): Peroxides, strong oxidizing agents.
5.4 Hazardous decomposition or byproducts: Irritating gases, CO and CO2
5.5 Hazardous polymerization: May occur: Will not occur: X
5.6 Conditions to avoid (polymerization): Elevated temperatures and oxidizing materials. Product is sensitive to
visible light. Heat greater than 70掳C(158掳F).
SECTION VI - Health Hazard Data
6.1 Route(s) of entry: Inhalation?: No Skin?: Yes Ingestion?: Yes
6.2 Health hazards (acute and chronic): Avoid contact with eyes and skin. Contact with eyes and skin may cause irritation.
Susceptible persons with known allergies or sensitivity to methacrylates and acrylates
may show allergic contact dermatitis and develop allergic response. Eyes: Material can
cause irritation. Skin: Material may be an irritant.
6.3 Carcinogenicity: NTP?: Not listed IARC monographs?: Not listed OSHA regulated?: No
6.4 Signs and symptoms of exposure: Dermal redness or irritation. Severe allergic response may result in breathing difficulties.
Eye contact: irritation and possible corneal damage. Skin contact: irritation or possible
allergic response.
6.5 Medical conditions generally
aggravated by exposure: Open sores and wounds of the skin. Individuals with known sensitivity to methacrylates
or urethane dimethacrylates.
6.6 Emergency first aid procedures: Eyes: In case of eye contact, flush with flowing water for 15 minutes. Get prompt
medical attention. Skin: Wash skin with mild soap and water. If irritation persists, call
physician. Ingestion: If swallowed give 2 glasses of water to drink. See a physician.
SECTION VII 鈥? Precautions for Safe Handling and Use
7.1 Steps to be taken in case material is
released or spilled: Spread vermiculite on paste to absorb any resin. Scoop up and place in an appropriately
marked container. Avoid gross skin contact to minimize the possibility of contact
dermatitis to susceptible persons.
7.2 Waste disposal methods: Dispose of in accordance with Federal, State and Local environmental control regulations.
7.3 Precautions to be taken in handling
and storage: Store away from food and beverages. Store away from extreme heat.
7.4 Other precautions: Observe normal warehouse handling procedures. Handling of this product should be by
trained dental healthcare professionals only.
SECTION VIII 鈥? Control Measures / Personal Protection
8.1 Respiratory protection: None required during normal use of this product.
8.2 Ventilation: None required during normal intended use of this product. Local exhaust can be
used to keep vapors below threshold level.
8.3 Protective gloves: Rubber gloves.
8.4 Eye protection: Protective goggles.
8.5 Other protective clothing or equipment: Rubber apron.
8.6 Work/Hygienic practices: Observe normal care when working with chemicals. Handling of this product
should be by trained dental healthcare professionals only.
NFPA HAZARD
CLASSIFICATIONS
Health 0 NFPA 鈥? National Fire Protection Association
Flammability 1 N.A. 鈥? Not Applicable
Reactivity 0 N.E. 鈥? Not Established
Specific Hazard N. A.
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP