Search   
MSDS 
:
 4-Bromochlorobenzene, 99%
CAS 
:
 106-39-8
SYNONYMS 
:
 None.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 106-39-8 |4-Bromochlorobenzene | 99.0 | 203-392-3 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI
Risk Phrases: 36/37/38

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Irritating to eyes, respiratory system and skin.The toxicological
properties of this material have not been fully investigated.

Potential Health Effects
Eye:
Causes eye irritation. The toxicological properties of this
material have not been fully investigated.
Skin:
Causes skin irritation. The toxicological properties of this
material have not been fully investigated.
Ingestion:
The toxicological properties of this substance have not been fully
investigated. Causes gastrointestinal tract irritation.
Inhalation:
Causes respiratory tract irritation. The toxicological properties of
this substance have not been fully investigated.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and
drink 2-4 cupfuls of milk or water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion.
Extinguishing Media:
In case of fire, use water, dry chemical, chemical foam, or
alcohol-resistant foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Sweep up, then place into a suitable container for
disposal. Avoid generating dusty conditions. Provide ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use only in a well-ventilated area. Minimize dust
generation and accumulation. Avoid contact with eyes, skin, and
clothing. Avoid ingestion and inhalation.
Storage:
Store in a cool, dry place. Keep container closed when not in use.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Use adequate general or local exhaust ventilation to keep airborne
concentrations below the permissible exposure limits. Use process
enclosure, local exhaust ventilation, or other engineering controls
to control airborne levels.
Exposure Limits
CAS# 106-39-8:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to minimize
contact with skin.
Respirators:
Wear a NIOSH/MSHA or European Standard EN 149
approved full-facepiece airline respirator in the
positive pressure mode with emergency escape
provisions. Follow the OSHA respirator regulations
found in 29 CFR 1910.134 or European Standard EN 149.
Use a NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Solid
Color: almost white
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 196 deg C @ 760.00mmHg
Freezing/Melting Point: 66.00 - 68.00 deg C
Autoignition Temperature: Not available.
Flash Point: Not available.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: insoluble
Specific Gravity/Density:
Molecular Formula: C6H4BrCl
Molecular Weight: 191.45

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, dust generation, excess heat, strong
oxidants.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Hydrogen chloride, carbon monoxide, irritating and toxic fumes and
gases, carbon dioxide, hydrogen bromide.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 106-39-8: CY9006000
LD50/LC50:
Not available.
Carcinogenicity:
4-Bromochlorobenzene -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****

Ecotoxicity:
Bacteria: Phytobacterium phosphoreum: EC50 = 4.59-6.49 mg/L; 5,15,30
Minutes; Microtox test, 15 degrees C

**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 106-39-8: No information available.
Canada
CAS# 106-39-8 is listed on Canada's NDSL List.
CAS# 106-39-8 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 106-39-8 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 5/05/1999 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
bis(2-Ethylhexyl) hydrogen phosphate, 95% (titr.) 298-07-7
Acriflavine Neutral, 13.3-15.8% Chlorine (on Dried Substance) 7782-50-5
p-Phenetidine, 98% 156-43-4
Cryptocyanine, 99% (UV-VIS) 4727-50-8
Methyl anthranilate 134-20-3
Phenylmercuric Nitrate, 62.75-63.50% Mercury 8003-05-2
Formaldehyde, 37 wt% solution in water, stabilized with 10-15% 50-00-0
2,4-Dimethyl-3-pentanol, 99+% 600-36-2
4-Bromochlorobenzene, 99% 106-39-8
Beta-Alanine, 98% 107-95-9
Tin (IV) Oxide, 99.995% 18282-10-5
Ethanesulfonic Acid, 99% 594-45-6
5-Methyl-3-heptanone, 98.5+% 541-85-5
m-Phenetidine, 98% 621-33-0
4-Dimethylaminobenzaldehyde, 98% 100-10-7
4-Dimethylaminobenzaldehyde, reagent acs 100-10-7
1,1,2,2-Tetrachloroethane, 97% 79-34-5
p-Phenylenediamine, 99+% 106-50-3
Hemin, bovine, crystalline, 98% 16009-13-5
2,6-Dimethylphenol, P.A. 576-26-1
beta-Methylstyrene, 99% trans, stabilized with 0.01% BHT 128-37-0
Diethyl Sulfate, 99% 64-67-5
3,5-Diiodosalicylic Acid, 97% (HPLC) 133-91-5
2-Sulfobenzoic Acid Cyclic Anhydride, Tech 81-08-3
1,5-Pentanediol, 98% 111-29-5
Dibenzyl Phosphate, 99% 1623-08-1
2-Methyl-1-undecene, 99+% 18516-37-5
2-Nitrobenzoic acid, 85-90%,(gc) 552-16-9
Lithium acetylide, ethylenediamine complex 85-92% 6867-30-7
3,3',4,4'-Benzophenonetetracarboxylic dianhydride, 96% 2421-28-5
trans-Cinnamaldehyde, 99% 104-55-2
Fullerene C70, 99+% (HPLC) 115383-22-7
3-Bromo-1-propanol, 98% 627-18-9
3-Nitrobenzyl chloride, 97+% (gc) 619-23-8
2,6-Diethylaniline, 98% 579-66-8
1,1,1-Trichloroethane, 93.5%, stabilized with ca. 5% 1,4-dioxane 71-55-6
Trimethyl Phosphate, 97% 512-56-1
2-(5-Bromo-2-Pyridylazo)-5-(Diethylamino)- Phenol, 97% 14337-53-2
Beta-Cyclodextrin Hydrate, 99% (HPLC) 68168-23-0
3,3'-Diethylthiadicarbocyanine Iodide, 99% (UV-VIS) 514-73-8
4-Methyl-1-cyclohexene, 99% 591-47-9
Mesityl oxide, 99%, mixt.of alpha- and bet a isomers(ca.93% alpha) 141-79-7
Butyl acrylate, 99+%, stabilized with 20 ppm MEHQ 141-32-2
Methyl diphenylphosphine, 99% 1486-28-8
2,5-Di-tert-butylhydroquinone 88-58-4
Orcinol, Monohydrate (Pract), 95% (UV-Vis) 6153-39-5
1-Iodohexane, 98+%,stabilized over copper 638-45-9
Octadecane, 99+% (gc) 593-45-3
Pamoic Acid, Disodium Salt Monohydrate, 98% (UV-Vis) 6640-22-8
Potassium fluoride 7789-23-3

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net