Search   
MSDS 
:
 3,3',4,4'-Benzophenonetetracarboxylic dianhydride, 96%
CAS 
:
 2421-28-5
SYNONYMS 
:
 4,4'-Carbonyldiphthalic anhydride, BTDA
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 2421-28-5 |3,3',4,4'-Benzophenonetetracarboxylic | 96.0 | 219-348-1 |
| |dianhydride | | |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI
Risk Phrases: 36/37

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Irritating to eyes and respiratory system.The toxicological
properties of this material have not been fully
investigated.Moisture sensitive.

Potential Health Effects
Eye:
Causes eye irritation.
Skin:
May cause skin irritation.
Ingestion:
May cause irritation of the digestive tract. The toxicological
properties of this substance have not been fully investigated.
Inhalation:
Causes respiratory tract irritation. The toxicological properties of
this substance have not been fully investigated.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of soap and water for at
least 15 minutes while removing contaminated clothing and shoes. Wash
clothing before reuse.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid. Wash mouth out with water.
Inhalation:
Remove from exposure to fresh air immediately. If not breathing,
give artificial respiration. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.
Antidote:
None reported.

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion.
Extinguishing Media:
Do NOT use water directly on fire. Use foam, dry chemical, or carbon
dioxide. Do NOT get water inside containers.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Vacuum or sweep up material and place into a suitable disposal
container. Clean up spills immediately, observing precautions in the
Protective Equipment section. Avoid generating dusty conditions.
Provide ventilation. Do not get water inside containers.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Use with adequate ventilation.
Minimize dust generation and accumulation. Avoid contact with eyes,
skin, and clothing. Keep container tightly closed. Avoid ingestion
and inhalation. Do not allow contact with water. Wash clothing
before reuse. Keep from contact with moist air and steam.
Storage:
Store in a tightly closed container. Store protected from moisture.
Store under nitrogen. Store in a cool, dry area away from
incompatible substances.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR ??1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant a respirator's use. Follow the OSHA
respirator regulations found in 29CFR 1910.134 or
European Standard EN 149. Always use a NIOSH or
European Standard EN 149 approved respirator when
necessary.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Solid
Appearance: light yellow powder
Odor: Odorless
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: 215 - 217 deg C
Autoignition Temperature: Not available.
Flash Point: 300 deg C ( 572.00 deg F)
Explosion Limits, lower: 4.20 vol %
Explosion Limits, upper: 16.00 vol %
Decomposition Temperature: 300 deg C
Solubility in water: reacts
Specific Gravity/Density:
Molecular Formula: C17H6O7
Molecular Weight: 322.22

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures. May decompose on
exposure to moist air or water.
Conditions to Avoid:
Incompatible materials, dust generation, moisture, excess heat,
exposure to moist air or water.
Incompatibilities with Other Materials:
Strong oxidizing agents, strong acids, strong bases, moisture.
Hazardous Decomposition Products:
Carbon monoxide, carbon dioxide.
Hazardous Polymerization: Will not occur.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 2421-28-5 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
3,3',4,4'-Benzophenonetetracarboxylic dianhydride -
Not listed by ACGIH, IARC, NIOSH, NTP, or OSHA.
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****

Other
No information available.

**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/37 Irritating to eyes and respiratory system.
Safety Phrases:
S 25 Avoid contact with eyes.
WGK (Water Danger/Protection)
CAS# 2421-28-5: No information available.
United Kingdom Occupational Exposure Limits

Canada
CAS# 2421-28-5 is listed on Canada's DSL List.
CAS# 2421-28-5 is not listed on Canada's Ingredient Disclosure List.
Exposure Limits
US FEDERAL
TSCA
CAS# 2421-28-5 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 4/23/1999 Revision #1 Date: 8/02/2000

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
bis(2-Ethylhexyl) hydrogen phosphate, 95% (titr.) 298-07-7
Acriflavine Neutral, 13.3-15.8% Chlorine (on Dried Substance) 7782-50-5
p-Phenetidine, 98% 156-43-4
Cryptocyanine, 99% (UV-VIS) 4727-50-8
Methyl anthranilate 134-20-3
Phenylmercuric Nitrate, 62.75-63.50% Mercury 8003-05-2
Formaldehyde, 37 wt% solution in water, stabilized with 10-15% 50-00-0
2,4-Dimethyl-3-pentanol, 99+% 600-36-2
4-Bromochlorobenzene, 99% 106-39-8
Beta-Alanine, 98% 107-95-9
Tin (IV) Oxide, 99.995% 18282-10-5
Ethanesulfonic Acid, 99% 594-45-6
5-Methyl-3-heptanone, 98.5+% 541-85-5
m-Phenetidine, 98% 621-33-0
4-Dimethylaminobenzaldehyde, 98% 100-10-7
4-Dimethylaminobenzaldehyde, reagent acs 100-10-7
1,1,2,2-Tetrachloroethane, 97% 79-34-5
p-Phenylenediamine, 99+% 106-50-3
Hemin, bovine, crystalline, 98% 16009-13-5
2,6-Dimethylphenol, P.A. 576-26-1
beta-Methylstyrene, 99% trans, stabilized with 0.01% BHT 128-37-0
Diethyl Sulfate, 99% 64-67-5
3,5-Diiodosalicylic Acid, 97% (HPLC) 133-91-5
2-Sulfobenzoic Acid Cyclic Anhydride, Tech 81-08-3
1,5-Pentanediol, 98% 111-29-5
Dibenzyl Phosphate, 99% 1623-08-1
2-Methyl-1-undecene, 99+% 18516-37-5
2-Nitrobenzoic acid, 85-90%,(gc) 552-16-9
Lithium acetylide, ethylenediamine complex 85-92% 6867-30-7
3,3',4,4'-Benzophenonetetracarboxylic dianhydride, 96% 2421-28-5
trans-Cinnamaldehyde, 99% 104-55-2
Fullerene C70, 99+% (HPLC) 115383-22-7
3-Bromo-1-propanol, 98% 627-18-9
3-Nitrobenzyl chloride, 97+% (gc) 619-23-8
2,6-Diethylaniline, 98% 579-66-8
1,1,1-Trichloroethane, 93.5%, stabilized with ca. 5% 1,4-dioxane 71-55-6
Trimethyl Phosphate, 97% 512-56-1
2-(5-Bromo-2-Pyridylazo)-5-(Diethylamino)- Phenol, 97% 14337-53-2
Beta-Cyclodextrin Hydrate, 99% (HPLC) 68168-23-0
3,3'-Diethylthiadicarbocyanine Iodide, 99% (UV-VIS) 514-73-8
4-Methyl-1-cyclohexene, 99% 591-47-9
Mesityl oxide, 99%, mixt.of alpha- and bet a isomers(ca.93% alpha) 141-79-7
Butyl acrylate, 99+%, stabilized with 20 ppm MEHQ 141-32-2
Methyl diphenylphosphine, 99% 1486-28-8
2,5-Di-tert-butylhydroquinone 88-58-4
Orcinol, Monohydrate (Pract), 95% (UV-Vis) 6153-39-5
1-Iodohexane, 98+%,stabilized over copper 638-45-9
Octadecane, 99+% (gc) 593-45-3
Pamoic Acid, Disodium Salt Monohydrate, 98% (UV-Vis) 6640-22-8
Potassium fluoride 7789-23-3

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net