Search   
MSDS 
:
 Pamoic Acid, Disodium Salt Monohydrate, 98% (UV-Vis)
CAS 
:
 6640-22-8
SYNONYMS 
:
 4,4'-Methylenebis (3-Hydroxy-2-Naphthalenecarboxylic Acid) Disodium     Salt
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 6640-22-8 |Pamoic Acid, Disodium Salt | 98% | 229-653-1 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: None Listed.
Risk Phrases: None Listed.

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
The toxicological properties of this material have not been fully
investigated.

Potential Health Effects
Eye:
May cause eye irritation. The toxicological properties of this
material have not been fully investigated.
Skin:
May cause skin irritation. The toxicological properties of this
material have not been fully investigated.
Ingestion:
May cause irritation of the digestive tract. The toxicological
properties of this substance have not been fully investigated.
Inhalation:
May cause respiratory tract irritation. The toxicological properties
of this substance have not been fully investigated.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and
drink 2-4 cupfuls of milk or water. Wash mouth out with water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. This
material in sufficient quantity and reduced particle size is capable
of creating a dust explosion.
Extinguishing Media:
Use agent most appropriate to extinguish fire. Use water spray, dry
chemical, carbon dioxide, or appropriate foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Vacuum or sweep up material and place into a suitable disposal
container. Clean up spills immediately, observing precautions in the
Protective Equipment section. Avoid generating dusty conditions.
Provide ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Use with adequate ventilation.
Minimize dust generation and accumulation. Avoid breathing dust,
vapor, mist, or gas. Avoid contact with eyes, skin, and clothing.
Avoid contact with skin and eyes. Keep container tightly closed.
Avoid ingestion and inhalation.
Storage:
Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Use adequate ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 6640-22-8:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Powder
Color: yellow
Odor: odorless
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: > 300 deg C
Autoignition Temperature: Not available.
Flash Point: Not available.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density:
Molecular Formula: C23H14O6Na2
Molecular Weight: 432.33

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable. However, may decompose if heated.
Conditions to Avoid:
Incompatible materials, dust generation, excess heat.
Incompatibilities with Other Materials:
Oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide.
Hazardous Polymerization: Will not occur.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 6640-22-8 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Pamoic Acid, Disodium Salt -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: Not available.
Risk Phrases:
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
S 28A After contact with skin, wash immediately with
plenty of water.
S 37 Wear suitable gloves.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 6640-22-8: No information available.
Canada
CAS# 6640-22-8 is listed on Canada's NDSL List.
CAS# 6640-22-8 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 6640-22-8 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 1/21/1999 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
bis(2-Ethylhexyl) hydrogen phosphate, 95% (titr.) 298-07-7
Acriflavine Neutral, 13.3-15.8% Chlorine (on Dried Substance) 7782-50-5
p-Phenetidine, 98% 156-43-4
Cryptocyanine, 99% (UV-VIS) 4727-50-8
Methyl anthranilate 134-20-3
Phenylmercuric Nitrate, 62.75-63.50% Mercury 8003-05-2
Formaldehyde, 37 wt% solution in water, stabilized with 10-15% 50-00-0
2,4-Dimethyl-3-pentanol, 99+% 600-36-2
4-Bromochlorobenzene, 99% 106-39-8
Beta-Alanine, 98% 107-95-9
Tin (IV) Oxide, 99.995% 18282-10-5
Ethanesulfonic Acid, 99% 594-45-6
5-Methyl-3-heptanone, 98.5+% 541-85-5
m-Phenetidine, 98% 621-33-0
4-Dimethylaminobenzaldehyde, 98% 100-10-7
4-Dimethylaminobenzaldehyde, reagent acs 100-10-7
1,1,2,2-Tetrachloroethane, 97% 79-34-5
p-Phenylenediamine, 99+% 106-50-3
Hemin, bovine, crystalline, 98% 16009-13-5
2,6-Dimethylphenol, P.A. 576-26-1
beta-Methylstyrene, 99% trans, stabilized with 0.01% BHT 128-37-0
Diethyl Sulfate, 99% 64-67-5
3,5-Diiodosalicylic Acid, 97% (HPLC) 133-91-5
2-Sulfobenzoic Acid Cyclic Anhydride, Tech 81-08-3
1,5-Pentanediol, 98% 111-29-5
Dibenzyl Phosphate, 99% 1623-08-1
2-Methyl-1-undecene, 99+% 18516-37-5
2-Nitrobenzoic acid, 85-90%,(gc) 552-16-9
Lithium acetylide, ethylenediamine complex 85-92% 6867-30-7
3,3',4,4'-Benzophenonetetracarboxylic dianhydride, 96% 2421-28-5
trans-Cinnamaldehyde, 99% 104-55-2
Fullerene C70, 99+% (HPLC) 115383-22-7
3-Bromo-1-propanol, 98% 627-18-9
3-Nitrobenzyl chloride, 97+% (gc) 619-23-8
2,6-Diethylaniline, 98% 579-66-8
1,1,1-Trichloroethane, 93.5%, stabilized with ca. 5% 1,4-dioxane 71-55-6
Trimethyl Phosphate, 97% 512-56-1
2-(5-Bromo-2-Pyridylazo)-5-(Diethylamino)- Phenol, 97% 14337-53-2
Beta-Cyclodextrin Hydrate, 99% (HPLC) 68168-23-0
3,3'-Diethylthiadicarbocyanine Iodide, 99% (UV-VIS) 514-73-8
4-Methyl-1-cyclohexene, 99% 591-47-9
Mesityl oxide, 99%, mixt.of alpha- and bet a isomers(ca.93% alpha) 141-79-7
Butyl acrylate, 99+%, stabilized with 20 ppm MEHQ 141-32-2
Methyl diphenylphosphine, 99% 1486-28-8
2,5-Di-tert-butylhydroquinone 88-58-4
Orcinol, Monohydrate (Pract), 95% (UV-Vis) 6153-39-5
1-Iodohexane, 98+%,stabilized over copper 638-45-9
Octadecane, 99+% (gc) 593-45-3
Pamoic Acid, Disodium Salt Monohydrate, 98% (UV-Vis) 6640-22-8
Potassium fluoride 7789-23-3

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net