**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 106-58-1 |N,N'-Dimethylpiperazine | 98 | 203-412-0 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: F C
Risk Phrases: 10 34
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable. Causes burns.Corrosive.
Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes
gastrointestinal tract burns.
Inhalation:
Causes chemical burns to the respiratory tract. Vapors may cause
dizziness or suffocation.
Chronic:
Not available.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately. Do NOT allow victim to rub eyes or keep eyes closed.
Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid immediately. Flush skin with plenty of water for at
least 15 minutes while removing contaminated clothing and shoes.
Wash clothing before reuse. Discard contaminated clothing in a manner
which limits further exposure. Destroy contaminated shoes.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid immediately. Do NOT induce vomiting. If conscious and alert,
rinse mouth and drink 2-4 cupfuls of milk or water.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If breathing is difficult, give oxygen. Do NOT use
mouth-to-mouth resuscitation. If breathing has ceased apply
artificial respiration using oxygen and a suitable mechanical device
such as a bag and a mask.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Will burn if involved in a fire. Use
water spray to keep fire-exposed containers cool. Containers may
explode in the heat of a fire. Flammable liquid and vapor. Vapors
may be heavier than air. They can spread along the ground and
collect in low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT use straight streams of
water. Cool containers with flooding quantities of water until well
after fire is out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Avoid runoff into storm sewers and
ditches which lead to waterways. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation. A
vapor suppressing foam may be used to reduce vapors. Water spray may
reduce vapor but may not prevent ignition in closed spaces. Stop
leak only if you can do so without risk.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Ground and bond containers when transferring material. Use
spark-proof tools and explosion proof equipment. Do not get in eyes,
on skin, or on clothing. Empty containers retain product residue,
(liquid and/or vapor), and can be dangerous. Keep container tightly
closed. Keep away from heat, sparks and flame. Do not ingest or
inhale. Use with adequate ventilation. Discard contaminated shoes.
Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
empty containers to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances.
Flammables-area.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use adequate ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 106-58-1:
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: colorless
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 131.0 - 132.0 deg C
Freezing/Melting Point: - 1.00 - - 0.00 deg
Autoignition Temperature: Not available.
Flash Point: 18 deg C ( 64.40 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: miscible
Specific Gravity/Density: .8440g/cm3
Molecular Formula: C6H14N2
Molecular Weight: 114.19
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat, strong
oxidants.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, carbon dioxide, nitrogen.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 106-58-1: TL5945000
LD50/LC50:
Not available.
Carcinogenicity:
N,N'-Dimethylpiperazine -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.*
Hazard Class: 3 (8)
UN Number: 2924
Packing Group: II
IMO
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.
Hazard Class: 3.2 (8)
UN Number: 2924
Packing Group: II
RID/ADR
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.
Hazard Class: 3
UN Number: 2924
Packing group: II
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: F C
Risk Phrases:
R 10 Flammable.
R 34 Causes burns.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 24/25 Avoid contact with skin and eyes.
S 33 Take precautionary measures against static
discharges.
S 50A Do not mix with acids.
WGK (Water Danger/Protection)
CAS# 106-58-1: 1
Canada
CAS# 106-58-1 is listed on Canada's DSL List.
CAS# 106-58-1 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 106-58-1 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 9/17/1998 Revision #2 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
N,N-Dibutylaniline, 99% (GC)
| 613-29-6 |
|
1,1,1,3,3,3-Hexafluoroacetone sesquihydrate, 98% (gc)
| 684-16-2 |
|
2-Biphenylyl Glycidyl Ether, 95%
| 7144-65-2 |
|
2,4-Dichlorobenzamide, 98%
| 2447-79-2 |
|
Isobutyl methacrylate, 99% (gc), stabilized with 15-20 ppm MEHQ
| 97-86-9 |
|
Picolinic acid n-oxide, 97%
| 824-40-8 |
|
N,n'-dimethylpiperazine, 98%
| 106-58-1 |
|
1,4-Dichlorobutane
| 110-56-5 |
|
1-Acetyl-4-Piperidinecarboxylic Acid, 99%
| 25503-90-6 |
|
Alpha, Alpha, Alpha-Trifluoro-O-Cresol 99%
| 444-30-4 |
|
Trans 2, cis 6-nonadienal diethylacetal, 80%
| 67674-36-6 |
|
Nitronium tetrafluoroborate,97%
| 13826-86-3 |
|
7-Methylindole, 99%
| 933-67-5 |
|
2,3,4,5,6-Pentafluoroaniline, 97%
| 771-60-8 |
|
9-Hydroxyxanthene, 99%
| 90-46-0 |
|
2'-Methoxyacetophenone, 99%
| 579-74-8 |
|
4-Methylindole, 99%
| 16096-32-5 |
|
Benzo[b]naphtho[2,3-d]furan, tech., 90+% (gc)
| 243-42-5 |
|
2-Methyl-3-nitrophenol, 98 %
| 5460-31-1 |
|
Diethylcarbamyl chloride, 99% (titr.)
| 88-10-8 |
|
2'-Chloroacetophenone, 97%
| 2142-68-9 |
|
Trifluoromethanesulfonic acid, 99%
| 1493-13-6 |
|
Acid Blue 45
| 2861-02-1 |
|
N-Alpha-Carbobenzyloxy-D-Arginine, 99+%
| 6382-93-0 |
|
1,2,7,8-Diepoxyoctane, 97%
| 2426-07-5 |
|
Tetrachlorophthalic anhydride, 98% (contains 0.5% Hexachlorobenzene)
| 117-08-8 |
|
4-Hydroxy-N-Methylpiperidine, 98%
| 106-52-5 |
|
Methyl 2,4-dihydroxybenzoate, 97%
| 2150-47-2 |
|
Calmagite, Indicator Grade
| 3147-14-6 |
|
Magnesium bromide hexahydrate, p.a.
| 13446-53-2 |
|
1,5-Naphthalenedisulfonic Acid Disodium Salt, Monohydrate, 95%
| 1655-29-4 |
|
(S)-(+)-2-Amino-2-Methylbutanedioic Acid, 99%
| 0-00-1 |
|
1-Hexanethiol, 99% (GC)
| 111-31-9 |
|
3-Fluorocinnamic Acid
| 458-46-8 |
|
1-Methyl-1-cyclohexanecarboxylic acid, 99%
| 1123-25-7 |
|
1,2-Ethanedisulfonic Acid Disodium Salt
| 5325-43-9 |
|
2-Aminopyrimidine (Pract)
| 109-12-6 |
|
Copper(II) trifluoromethanesulfonate
| 34946-82-2 |
|
4-Nitrobenzenediazonium tetrafluoroborate (pract), 95% (uv-vis)
| 456-27-9 |
|
D-(-)-Gulose, 93-95%, mixture of anomers
| 4205-23-6 |
|
3-Acetoxyacetophenone, 99%
| 2454-35-5 |
|
1-Hydroxy-2,2,5,5-tetramethyl-3-imidazoline 3-oxide, 99%
| 33455-68-4 |
|
(S)-(+)-Glycidyl nosylate, 98%
| 115314-14-2 |
|
2,5-Diaminobenzenesulfonic Acid, Tech. 90%
| 88-45-9 |
|
Selenium atomic absorption standard solution, 1 mg/ml se in 10% hcl
| 7647-01-0 |
|
6-Quinolinecarboxylic Acid, 98% (Titr.)
| 10349-57-2 |
|
2,2-Diphenylpropionic Acid, 97%
| 5558-66-7 |
|
4-Aminoantipyrine
| 83-07-8 |
|
Methyl 3,5-Dimethoxybenzoate, 99%
| 2150-37-0 |
|
N,2,3-Trimethyl-2-Isopropylbutamide
| 51115-67-4 |
|
|