=====================  Product Identification  =====================

MSDS NAME:HEAT RESISTING EN-TTE496 A 14391
NIIN:00-297-2012
MSDS Number: BHMMC
=== Responsible Party ===
Company:WARREN PAINT AND COLOR COMPANY
Address:700 WEDGEWOOD AVENUE
City:NASHVILLE
State:TN
ZIP:37203
Country:US
Info Phone Num:615-292-6655
Emergency Phone Num:615-292-6655
CAGE:1J302
=== Contractor Identification ===
Company:WARREN PAINT AND COLOR COMPANY
Box:City:NASHVILLE
State:TN
ZIP:37203-5526
Country:US
Phone:615-292-6655
CAGE:1J302

=============  Composition/Information on Ingredients  =============

Name:MINERAL SPIRITS					       
    (VAPOR PRESSURE 6.2 MMHG @ 100 F)
CAS:64475-85-0
RTECS #:PY8240000
Fraction by Wt: 52.91%
OSHA PEL:500.00 PPM

=====================  Hazards Identification  =====================

Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Effects of Overexposure:INHAL: DIZZINESS, BREATHING DIFF, HEADACHES &
    LOSS OF COORDINATION. EYE: SEVERE IRRI, TEARS, REDNESS & BLURRED
    VISION. SKIN: DRY & DEFAT SKIN CAUSING CRACKS,   IRRI & DERMITITIS.
    INGESTION: CAN CAUSE  GASTROINTESTINAL IRRI, VOMTNG, NAUSEA
    &DIARRHEA
Medical Cond Aggravated by Exposure:ANESTHESIA, RESPIRATORY TRACT
    IRRITATION, DERMIT- ITIS, NAUSEA AND VOMITING.

=======================  First Aid Measures  =======================

First Aid:INHAL: MOVE PERSON TO FRESH AIR. IF BREATHING STOPS, APPLY
    CPR & SEEK IMMEDIATE MED ATTN. EYE: FLUSH WITH LARGE AMTS OF WATER
    15 MIN. SKIN: WASH THOROUGHLY WITHSOAP & WATER & SEEK MED ATTN. &
    INGES: D O NOT INDUCE VOMIT, CAN CAUSE CHEMICALPHEUMONITIS &
    PULMONARY EDEMA. CONTACT PHYSICIAN IMMEDIATELY.

=====================  Fire Fighting Measures  =====================

Flash Point Method:TCC
Flash Point:103 F/39.44 C
Extinguishing Media:FOAM, ALCOHOL FOAM, CO2, DRY CHEMICAL, WATER FOG,
    OTHER
Fire Fighting Procedures:HANDLE AS COMBUSTIBLE MATERIAL. VAPORS FORM
    EXPLOSIVE MIX IN AIR BETWEEN UPPER &LOWER EXPLOSIVE LIMITS CAN
    IGNITE BY MANY SOURCES; PILOT LIGHTS, OPEN FLAMES
Unusual Fire/Explosion Hazard:RESPIRATORY EQUIP SHOULD BE WORN TO AVOID
    INHAL OF CONCENTRATED VAPORS. WATER   SHOULD NOT BE USED EXCEPT AS
    FOG TO KEEP NEARBY CONTAINERS COOL.

==================  Accidental Release Measures  ==================

Spill Release Procedures:ELIMINATE IGNITION SOURCES, PROVIDE GOOD
    VENTILA- TION, DIKE SPILL AREA & ADD ABSORBENT EARTH OR SAWDUST TO
    SPILLED LIQUID

======================	Handling and Storage  ======================

Handling and Storage Precautions:USE NON-SPARKING UTENSILS WHEN
    HANDLING THIS MATERIAL. AVOID HOT METAL SURFACES. USE IN COOL, WELL
     VENTED AREAS. KEEP CONTAINERS CLOSED WHEN NOT USED
Other Precautions:KEEP AWAY FROM EXCESSIVE HEAT & OPEN FLAME. SMOKING
    IN AREAS WHERE THIS MATERIALIS USED SHOULD BE STRICTLY PROHIBITED.
    NOTE: THIS INFORMATION IS ACCURATE TO THEBEST KNOWLEDGE OF WARREN
    PAINT & COLOR C O., BUT IS FUNISHED WITHOUT WARRANTIES

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE A NIOSH APPROVED CARTRIDGE RESPIRATOR OR GAS
    MASK SUITABLE TO KEEP AIRBORNE MISTS & VAPOR CONCENTRATION BELOW
    THE TIMEWEIGHTED THRESHOLD LIMIT VALUES. CON- FINED AREA: FRESH-AIR
    SUPPLY RESPIRATORY	OR SELF CONTAINED BREATHING APPARATUS
Ventilation:GEN MECHANICAL VENT OR LOCAL EXHAUST SUITABLE TO KEEP
    VAPORSBELOW TLV. VENTILATION EQUIP SHOULD BE EXPLOSION PROOF
Protective Gloves:IMPERMEABLE CHEMICAL GLOVES
Eye Protection:CHEM SAFETY GLASSES/GOGGLES/FACESHIELDS
Other Protective Equipment:IMPERMEABLE APRONS & PROTECTIVE CLOTHING
    WHENEVER POSSIBLE  TO PREVENT SKIN CONTACT. HEAD CAPS STRONGLY
    RECOMMENDED
Work Hygienic Practices:EYE WASHES & SAFETY SHOWERS IN THE WORKPLACE IS
    RECOMMENDED
Supplemental Safety and Health
NK

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:307 F
Vapor Density:> AIR
Evaporation Rate & Reference:41.40 (ETHYL ETHER = 1)
Percent Volatiles by Volume:60.86

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
ALKALINE MATERIALS, STRONG ACIDS AND OXIDIZING MATERIALS
Stability Condition to Avoid:EXCESSIVE HEAT, POOR VENTILATION,
    CORROSIVE ATMOSPHERES,    EXCESSIVE AGING.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
    OXIDES OF NITROGEN

====================  Disposal Considerations  ====================

Waste Disposal Methods:COLLECT ABSORBENT/SPILLED LIQUID MIXTURE INTO   
     METAL CONTAINERS. CONSULT LOCAL, STATE & FEDERAL  HAZARDOUS WASTE
    LANDFILLS. OBEY RELEVANT LAWS

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***