MATERIAL SAFETY DATA SHEET
Coated Abrasives
IDENTITY TRADE NAME
COATED ABRASIVE CERAMIC GRAIN S-20
SECTION I (MATERIAL IDENTIFICATION)
MANUFACTURER'S NAME EMERGENCY TELEPHONE NUMBER
F谩brica Nacional de Lija, S.A de C.V. 011 525 3661403
ADDRESS (Street, Number, City, State, ZIP Code) TELEPHONE & FAX NUMBER FOR INFORMATION
Av. Presidente Ju谩rez # 225 011 525 366 1400 fax 011 525 366 1499
San Jer贸nimo Tepetlacalco REVISION DATE
Tlalnepantla 54000 October, 2006
Estado de M茅xico PREPARED BY (Technical contact)
MEXICO Alfredo Ba帽uelos or Jos茅 Jim茅nez
SECTION II (MATERIAL DESCRIPTION & HAZARD RATING)
TECHNICAL DESCRIPTION: Ceramic Aluminum Oxide coated HAZARD RATING: 1, 0, 0 NFPA CODE
on a polyester backing with a resin binder.
CHEMICAL FAMILY Blue: Health hazard 0: Minimum
0
NA Red: Fire hazard 1: Slight
CHEMICAL NAME/FORMULA Yellow: Reactivity hazard 2: Moderate
1 0
NA White: Special hazard 3: Serious
SYNONYMOUS 4: Extreme
NA
SECTION III (HAZARDOUS INGREDIENTS/IDENTITY INFORMATION)
HAZARDOUS COMPONENTS
Chemical name CAS No. Common name (s) Percent OSHA - PEL (mg/m3) ACGIH-TLV (mg/m3)
Aluminum Oxide (Al2O3) 1344 - 28 - 1 Alpha alumina 6.2 - 12.5 15.0 (total dust) 10.0 (total dust)
Ceramic Aluminum Oxide
66402 - 68 - 4 Ceramic alumina 14.5 - 28.6 --- ---
(Al2O3)
Polyester Backing None Synthetic Cloth 12.6 - 33.6 --- ---
Phenol - Formaldehyde None Phenolic Resin 16.5 - 17.8 --- ---
Resin "cured".
--- ---
Styrene-butadiene latex 9003 - 55 - 8 SBR latex 2.9 - 8.0
Calcium fluoride 14542 - 23 -5 Fluorspar 2.8 - 3.3 2.5 2.5
Potassium fluoroborate 14075 - 53 - 7 Potassium fluoroborate 6.1 - 11.2 2.5 2.5
Chlorazol Black E* 1937 - 37 - 7 Direct Black E-38* 4.8 - 13 ppm --- ---
REMARKS
The above materials are not carcinogen, except (*)
Materials are regulated by OSHA 29 CFR 1910.1200, Hazard Communication and/or The Massachusetts General Law, Chapter III, Right to know Regulations
SECTION IV (PHYSICAL & CHEMICAL CHARACTERISTICS)
BOILING POINT NA SOLUBILITY IN WATER NA SPECIFIC GRAVITY (H2O=1) NA
VAPOR PRESSURE NA SOLUBILITY IN ALCOHOL NA MELTING POINT NA
VAPOR DENSITY (Air = 1) NA SOLUBILITY IN OTHER SOLVENT NA % VOLATILE BY VOLUME NA
APPEARANCE & ODOR Cloth coated with abrasive particles which are EVAPORATION RATE NA
bonded with resin binder.
SECTION V (FIRE & EXPLOSION HAZARD DATA)
FLASH POINT (Method used) FLAMMABLE LIMITS LEL UEL
NA NA NA NA
EXTINGUISHED MEDIA
Water, carbon dioxide, Dry chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES
Backings and cured resin will burn or decompose.
Use respiratory protection.
UNUSUAL FIRE & EXPLOSION HAZARDS
NA
MATERIAL SAFETY DATA SHEET
Coated Abrasives
IDENTITY TRADE NAME
COATED ABRASIVE CERAMIC GRAIN S-20
SECTION I (MATERIAL IDENTIFICATION)
SECTION VI (REACTIVITY DATA)
STABILITY UNSTABLE CONDITIONS TO AVOID
STABLE X NA
INCOMPATIBILITY (Materials to Avoid)
In use organic fumes may be liberated.
HAZARDOUS DECOMPOSITION OR BY PRODUCTS
HAZARDOUS MAY OCCUR CONDITIONS TO AVOID
POLYMERIZATION WILL NOT OCCUR X NA
SECTION VII (HEALTH HAZARD DATA)
ROUTE (s) OF ENTRY INHALATION SKIN INGESTION
During use Airborne dusts or fumes. Airborne dusts or fumes. Airborne dusts or fumes.
HEALTH HAZARDS (Acute & crhonic) ACUTE: Breathing difficulty, skin, eye, nasal and respiratory irritation; organic fumes can cause gastric pain,
internal bleeding or tissue damage. CHRONIC: exposure to organic fumes (fluoride) has been reported to cause osteosclerosis, mottling of tooth enamel and
damage to skin, eye and mucous membranes.
CARCINOGENICITY NTP IARC MONOGRAPHS OSHA REGULATED
NA NA NA
SIGNS & SYMPTOMS OF EXPOSURE Deposits or material on skin, in eyes and nasal passages. Coughing and/or breathing difficulties
may be present.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE Pulmonary disorders, skin or eye disorders.
EMERGENCY & FIRST AID PROCEDURES
Remove to dust free area. Irrigate eyes and/or skin with copious amounts of water.
SEEK MEDICAL ATTENTION.
SECTION VIII (PRECAUTIONS FOR SAFE HANDLING & USE)
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Ordinary precautions for dust and particulates.
WASTE DISPOSAL METHOD
In compliance with Federal, State and local regulations for landfill.
PRECAUTIONS TO BE TAKEN IN HANDLING & STORING
Not applicable
OTHER PRECAUTIONS
Not applicable
SECTION IX (CONTROL MEASURES)
RESPIRATORY PROTECTION (Specify type) If limits are exceeded during sanding or grinding, an approved NIOSH repirator
must be used. OSHA 29 CRF 1910 - 134
VENTILATION LOCAL EXHAUST Must be used to control exposure to dust or fumes. SPECIAL NA
MECHANICAL (General) Hoods connected to exhaust ducts and appropiate dust collector.
PROTECTIVE GLOVES Wear gloves to prevent EYE PROTECTION Wear safety glasses while sanding or grinding.
abrasion and/or skin irritation. OSHA 29 CFR 1910 . 133
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
Hearing protection OSHA 29 CFR 1910 . 215
WORK/HYGIENIC PRACTICES
Ordinary washing and cleanliness practices.
ABREVIATIONS: NA = NOT APPLICABLE
"THE INFORMATION IS PROVIDED IN GOOD FAITH AND IS BASED ON DATA CONSIDERED ACCURATE, HOWEVER, FABRICA NACIONAL
DE LIJA, S.A de C.V. MAKES NO WARRANTY WITH RESPECT OF THE ACCURACY OF THE INFORMATION AND DISCLAIMS RESPONSABILITY FOR
DAMAGES OF ANY KIND RESULTING FROM THE USE OF THIS DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF. CUSTOMERS
ARE ENCOURAGED TO MAKE THEIR OWN DETERMINATION AS TO THE SUITABILITY OF THIS PRODUCT FOR THEIR PURPOSE PRIOR TO USE".
|