MOLYTEC AUSTRALIA, Unit 1, 9 Steel St, Capalaba, QLD Australia, 4157
Tel. for Information: (07) 3245 2355 Fax for Information: (07) 3245 2499
Last Updated: April 2008 Page 1 of 2
Material Safety Data Sheet ULTRALOC 3660 anaerobic
Classified as Hazardous according to criteria of NOHSC.
Chemical Product / Company Identification
1.
Product Name: ULTRALOC 3660 Retaining Compound
Product Type: Anaerobic Adhesive
Product Size: 50mL P/No. 366050
Company Details: Molytec Australia P/L 1/9 Steel St Capalaba QLD Australia 4157
Phone: 07 3245 2355 Fax: 07 3245 2499
Composition and Information on Harmful Ingredients
2.
Hazardous components CAS No. ACGIH TLV OSHA PEL
Aromatic dimethacrylate ester 24448-20-2 60-100 None None
Maleimide Resin 3006-93-7 10-30 None None
Saccharin 81-07-2 1-5 None None
Silica, amorphous, fumed, crystalline-free 112945-52-5 1-5 6mg/m3 TWA 10mg/m3 TWA
Cumene hydroperoxide 80-15-9 1-5 None None
Hydroxyalkyl methacrylate 27813-02-1 1-5 None None
Bisphenol A Fumarate Resin 39382-25-7 10-30 None None
Hazards Identification
3.
Relevant routes of exposure: Skin, Inhalation, Eyes
Potential Health Effects
Inhalation: May cause respiratory tract irritation.
Skin contact: May cause allergic skin reaction. May cause skin irritation.
Eye contact: Contact with eyes will cause irritation.
Ingestion: Not expected to be harmful by ingestion.
HMIS:
Health: 1 FLAMMABILITY: 1 REACTIVITY: 1 PPE: H
WARNING: CAUSES EYE IRRITATION.
MAY CAUSE SKIN IRRITATION.
MAY CAUSE ALLERGIC SKIN REACTION.
MAY CAUSE RESPIRATORY TRACT IRRITATION.
4. First Aid Measures
Ingestion: Do not induce vomiting. Keep individual calm. Obtain medical attention.
Inhalation: Remove to fresh air. If symptoms develop and persists, get medical attention.
Skin contact: Wash with soap and water. Remove contaminated clothing and shoes. Wash clothing
before reuse. Get medical attention if symptoms occur.
Eye contact: Flush with copious amounts of water, preferably lukewarm water, for at least 15 minutes,
holding eyelids open all the time. Get medical attention.
Fire Fighting Measures
5.
Flash Point: Greater than 93掳C (200掳F) Cleveland closed cup
Autoignition temperature: Not available.
Flammable/Explosive limits 鈥搇ower%: 2.6% (propylene glycol)
Flammable/Explosive limits 鈥搖pper%: 12.5% (propylene glycol)
Extinguishing media: Foam, dry chemical or carbon dioxide.
Special fire fighting procedures: None
Unusual fire or explosion hazards: None
Hazardous combustion products: Oxides of carbon. Oxides of sulfur. Oxides of nitrogen. Irritating organic
vapours.
6. Accidental Release Measures
Environmental precautions: Prevent product from entering drains or open waters.
Clean-up methods: Soak up with inert absorbent. Store in partly filled, closed container until disposal.
7. Handling and Storage
Handling: Avoid contact with eyes, skin and clothing. Avoid breathing vapour and mist. Wash
thoroughly after handling.
Storage: For safe storage, store at or below 38掳C (100掳F). Keep in a cool, well ventilated
area away from heat, sparks and open flame. Keep container tightly closed until
ready for use.
Incompatible products: Refer to Section 11.
8. Exposure Control and Personal Protection See Section 3 for exposure limits.
Engineering controls: No specific ventilation requirements noted, but forced ventilation may still be
required if concentrations exceed occupational exposure limits.
Respiratory protection: Use NIOSH approved respirator if there is potential to exceed exposure limit(s).
Skin protection: Use impermeable gloves and protective clothing as necessary to prevent skin
contact. Neoprene gloves. Butyl rubber gloves. Natural rubber gloves.
Eye/face protection: Safety goggles or safety glasses with side shields.
3660
MOLYTEC AUSTRALIA, Unit 1, 9 Steel St, Capalaba, QLD Australia, 4157
Tel. for Information: (07) 3245 2355 Fax for Information: (07) 3245 2499
Last Updated: April 2008 Page 2 of 2
Material Safety Data Sheet ULTRALOC 3660 anaerobic
Physical and Chemical Properties
9.
Physical state: Liquid
Color: Grey
Odor: Mild
Vapour pressure: Less than 5 mm Hg at 27掳C (80掳F)
pH: Not applicable
Boiling point/range: Greater than 149掳C (300掳F)
Melting point/range: Not available
Specific gravity: 1.1 at 23.9掳C (75掳F)
Vapor density: Not available
Evaporation rate: Not available
Solubility in water: Slight
VOC content: 4.39%; 48.6 grams/litre (EPA Method 24)
Stability and Reactivity
10.
Stability: Stable.
Hazardous polymerisation: Will not occur.
Hazardous decomposition products: Oxides of carbon. Oxides of sulfur. Oxides of nitrogen. Irritating organic
vapours.
Incompatibility: Strong oxidizers. Free radical initiators. Strong reducing agents. Alkalis.
Oxygen scavengers. Other polymerisation initiators. Copper. Iron. Zinc.
Aluminium. Rust.
Conditions to avoid: See 鈥淗andling and Storage鈥? (Section 8) and 鈥淚ncompatibility鈥? (Section 11).
11. Toxicological Information
Product toxicity: Acute oral LD50 greater than 10,000 mg/kg (rat). Acute dermal LD50 greater than 5000 mg/kg (rabbit).
Carcinogen Status
Hazardous components NTP Carcinogen IARC Carcinogen OSHA Carcinogen
Polyglycol dimethacrylate No No No
Polyglycol oleate No No No
Saccharin No No No
Sillica, amorphous, fumed, crystalline-free No No No
Cumene hydroperoxide No No No
Propylene glycol No No No
Ecological Information
12.
Ecological Information: Not Available
Disposal Considerations
13.
Recommended method of disposal: Dispose of according to Federal, State and local government regulations.
EPA hazardous waste number: Not a RCRA hazardous waste.
14. Transport Information
Not classified as a Dangerous Good according to the Australian Code for the Transport of Dangerous Goods by Road
and Rail.
15. Regulatory Information
None Available
16. Other Information
Users should verify the currency of this data sheet if more than 5 years old. The information contained in this material
safety data sheet is believed to be accurate on the date of issue and in accordance with the information available to us.
Persons dealing with products referred to in this MSDS do so at their own risk. We accept no liability whatsoever for
damage or injury however caused arising from use of this information or of suggestions contained herein.
POLICE AND FIRE BRIGADE: DIAL 000
For further safety information contact Denis Brown at MOLYTEC AUSTRALIA on:
Tel: (07) 3245 2355 Fax: (07) 3245 2499
P.O. Box 5357, Alexandra Hills, QLD, Australia, 4161
Disclaimer
The information contained within this MSDS applies only to the ULTRALOC product to which the sheet relates. The information
provided is based on our best knowledge at the time of issue. The information contained within this MSDS is believed to be accurate
and is given in good faith. However no warranty is made, either express or implied, regarding its accuracy or any liability arising out of
the use of the information herein or the products supplied. When used in other preparations, formulations, or in mixtures, it is
necessary to ascertain whether the classification of the hazards have changed. The attention of the user is drawn to the possibility of
creating other hazards when the product is used for purposes other than that for which it was recommended. In such cases a
reassessment may be necessary and should be made by the user. This safety data sheet should only be used and reproduced in
order that the necessary measures are taken relating to the protection of health and safety at work. It is the responsibility of the
handlers to pass on the totality of the information contained within this document to any subsequent person(s) who will come in to
contact with, handle or use this product in any way. They should check the adequacy of the information provided within this MSDS
before passing it on to their customers / staff.
END OF DOCUMENT
3660
|