Material Safety Data
Sheet
SECTION 1 PRODUCT AND COMPANY IDENTIFICATION
SOLTROL 庐 10 ISOPARAFFIN SOLVENT
Product Use: Solvent
Product Number(s): 0001017314, 0001017315, 0001017316, 0001017317, 0001017320, 0001017321
Synonyms: Not Established
Product Cas No.: 70024-92-9
Company Identification: Product Information:
Chevron Phillips Chemical Company LP MSDS Requests: (800) 852 - 5530
Specialty Chemicals Technical Information: (832) 813 - 4862
10001 Six Pines Drive
The WoodlandsTX 77380
24-Hour Emergency Telephone Numbers
HEALTH:Chevron Phillips Emergency Information Center 866.442.9628 (North America) and
1.832.813.4984 (International)
TRANSPORTATION: North America: CHEMTREC 800.424.9300 or 703.527.3887
ASIA: +1.703.527.3887
EUROPE: BIG .32.14.584545 (phone) or .32.14.583516 (telefax)
SOUTH AMERICA SOS-Cotec Inside Brazil: 0800.111.767
Outside Brazil: 55.19.3467.1600
SECTION 2 COMPOSITION/ INFORMATION ON INGREDIENTS
COMPONENT CAS AMOUNT EINECS SYM R-PHRASES
NUMBER
ISOALKANES 7-8 70024-92-9 100 % weight 2742-73-1 NA NA
Occupational Exposure Limits:
Component Limit TWA STEL Ceiling / Peak Notation
ISOALKANES 7-8 CPCHEM 300 ppm NA NA NA
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
1 of 9
Revision Date: 01/25/2005 MSDS : 34750
SECTION 3 HAZARDS IDENTIFICATION
**************************************************************************************************************
EMERGENCY OVERVIEW
Colorless liquid at room temperature. Mild hydrocarbon odor.
- HIGHLY FLAMMABLE LIQUID AND VAPOR. VAPOR MAY CAUSE FLASH FIRE
- HARMFUL OR FATAL IF SWALLOWED - CAN ENTER LUNGS AND CAUSE DAMAGE
- CAUSES EYE IRRITATION
- TOXIC TO AQUATIC ORGANISMS
**************************************************************************************************************
IMMEDIATE HEALTH EFFECTS:
Eye: Contact with the eyes causes irritation. Symptoms may include pain, tearing, reddening, swelling
and impaired vision. Not expected to cause prolonged or significant eye irritation.
Skin: Prolonged or repeated skin contact may cause drying or defatting of the skin. Symptoms may
include pain, itching, discoloration, swelling, and blistering. Not expected to be harmful to internal organs
if absorbed through the skin.
Ingestion: This material can directly enter the lungs, if swallowed, or if subsequently vomited. Once in
the lungs it is very difficult to remove and can cause severe injury or death.
Inhalation: Not expected to be harmful if inhaled.
SECTION 4 FIRST AID MEASURES
Eye: Flush eyes with running water immediately while holding the eyelids open. Remove contact lenses,
if worn, after initial flushing, and continue flushing for at least 15 minutes. Get immediate medical
attention.
Skin: To remove the material from skin, use soap and water. Discard contaminated clothing and shoes
or thoroughly clean before reuse. Get medical attention if any symptoms develop.
Ingestion: If swallowed, do not induce vomiting. Give the person a glass of water or milk to drink and get
immediate medical attention. Never give anything by mouth to an unconscious person.
Inhalation: Move the exposed person to fresh air. If not breathing, give artificial respiration. If breathing
is difficult, give oxygen. Get medical attention if breathing difficulties continue.
Note to Physicians: Ingestion of this product or subsequent vomiting may result in aspiration of light
hydrocarbon liquid, which may cause pneumonitis.
SECTION 5 FIRE FIGHTING MEASURES
See Section 7 for proper handling and storage.
FIRE CLASSIFICATION:
OSHA Classification (29 CFR 1910.1200): Flammable liquid.
NFPA RATINGS: Health: 1 Flammability: 3 Reactivity: 0
FLAMMABLE PROPERTIES:
Flashpoint: -11 掳C (12.2掳F) (Tag Closed Cup)
Autoignition: 420 掳C (788掳F)
Flammability (Explosive) Limits (% by volume in air): Lower: 1 Upper: 6.6
EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish
flames.
PROTECTION OF FIRE FIGHTERS:
Fire Fighting Instructions: For fires involving this material, do not enter any enclosed or confined fire
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
2 of 9
Revision Date: 01/25/2005 MSDS : 34750
space without proper protective equipment, including self-contained breathing apparatus.
Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne
solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic
compounds will be evolved when this material undergoes combustion. Combustion may form: Carbon
Dioxide, Carbon Monoxide
SECTION 6 ACCIDENTAL RELEASE MEASURES
Protective Measures: Eliminate all sources of ignition in the vicinity of the spill or released vapor. If this
material is released into the work area, evacuate the area immediately. Monitor area with combustible
gas indicator. Wear appropriate personal protective equipment when cleaning up spills. Refer to Section
8.
Spill Management: Stop the source of the release if you can do it without risk. Contain release to
prevent further contamination of soil, surface water or groundwater. Clean up spill as soon as possible,
observing precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as
applying non-combustible sorbent materials or pumping. All equipment used when handling the product
must be grounded. A vapor suppressing foam may be used to reduce vapors. Use clean non-sparking
tools to collect absorbed material. Where feasible and appropriate, remove contaminated soil. Place
contaminated materials in disposable containers and dispose of in a manner consistent with applicable
regulations.
Reporting: U.S.A. regulations require reporting spills of this material that could reach any surface waters.
Report spills to local authorities and/or the National Response Center at (800) 424-8802 as appropriate or
required.
SECTION 7 HANDLING AND STORAGE
READ AND OBSERVE ALL PRECAUTIONS ON PRODUCT LABEL . REFER TO PRODUCT LABEL OR
MANUFACTURERS TECHNICAL BULLETINS FOR THE PROPER USE AND HANDLING OF THIS MATERIAL .
Precautionary Measures: This material presents a fire hazard. Liquid quickly evaporates and forms
vapor (fumes) which can catch fire and burn with explosive violence. Invisible vapor spreads easily and
can be set on fire by many sources such as pilot lights, welding equipment, and electrical motors and
switches. Fire hazard is greater as liquid temperature rises above 15F. Do not get in eyes.
General Handling Information: Avoid work practices that may release volatile components in the
atmosphere. Local air pollution regulations should be consulted to determine if the release of volatile
components is regulated or restricted in the area in which this material is used. Avoid contaminating soil
or releasing this material into sewage and drainage systems and bodies of water.
Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling
this material. To minimize this hazard, bonding and grounding may be necessary but may not, by
themselves, be sufficient. Review all operations, which have the potential of generating an accumulation
of electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash filling,
tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations)
and use appropriate mitigating procedures. For more information, refer to OSHA Standard 29 CFR
1910.106, 'Flammable and Combustible Liquids, National Fire Protection Association (NFPA 77),
Recommended Practice on Static Electricity' (liquids, powders and dusts), and/or the American Petroleum
Institute (API) Recommended Practice 2003, 'Protection Against Ignitions Arising Out of Static, Lightning,
and Stray Currents' (liquids).
General Storage Information: DO NOT USE OR STORE near heat, sparks or open flames. USE AND
STORE ONLY IN WELL VENTILATED AREA. Keep container closed when not in use. Container is not
designed to contain pressure. Do not use pressure to empty container or it may rupture with explosive
force. Empty containers retain product residue (solid, liquid, and/or vapor) and can be dangerous. Do
not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks,
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
3 of 9
Revision Date: 01/25/2005 MSDS : 34750
static electricity, or other sources of ignition. They may explode and cause injury or death. Empty
containers should be completely drained, properly closed, and promptly returned to a drum reconditioner,
or disposed of properly.
Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty
container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid,
and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode
and cause injury or death. Empty containers should be completely drained, properly closed, and promptly
returned to a drum reconditioner or disposed of properly.
SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION
GENERAL CONSIDERATIONS:
Consider the potential hazards of this material (see Section 3) applicable exposure limits, job activities,
and other substances in the work place when designing engineering controls and selecting personal
protective equipment. If engineering controls or work practices are not adequate to prevent exposure to
harmful levels of this material, the personal protective equipment listed below is recommended. The user
should read and understand all instructions and limitations supplied with the equipment since protection is
usually provided for a limited time or under certain circumstances.
ENGINEERING CONTROLS:
Use in a well-ventilated area.
PERSONAL PROTECTIVE EQUIPMENT:
Eye/Face Protection: Wear eye protection such as safety glasses, chemical goggles, or faceshields if
engineering controls or work practices are not adequate to prevent eye contact.
Skin Protection: Wear impervious protective clothing to prevent skin contact. Selection of protective
clothing may include gloves, apron, boots, and complete facial protection depending on operations
conducted. Users should determine acceptable performance characteristics of protective clothing.
Consider physical requirements and other substances present when selecting protective clothing.
Suggested materials for protective gloves include: Nitrile Rubber, or Polyurethane, or Viton
Respiratory Protection: If exposure is anticipated to be greater than applicable exposure limits, wear a
NIOSH approved respirator that provides adequate protection from measured concentrations of this
material. Use the following elements for air-purifying respirators: Air-Purifying Respirator for Organic
Vapors
Use a positive pressure, air-supplying respirator if there is potential for uncontrolled release, exposure
levels are not known, or other circumstances where air-purifying respirators may not provide adequate
protection.
Occupational Exposure Limits:
Component Limit TWA STEL Ceiling / Peak Notation
ISOALKANES 7-8 CPCHEM 300 ppm NA NA NA
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE AND ODOR: Colorless liquid at room temperature. Mild hydrocarbon odor.
pH: NA
VAPOR PRESSURE: 2.2 psia @ 38潞C (100掳F)
VAPOR DENSITY (AIR=1): >2
BOILING POINT: 93.3 掳C (199.94掳F)104.4掳C (219.92掳F)
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
4 of 9
Revision Date: 01/25/2005 MSDS : 34750
SOLUBILITY (in water): Negligible
VISCOSITY: 0.56 cSt @ 40 潞C (104掳F)
PERCENT VOLATILE: 100 % volume
SPECIFIC GRAVITY: 0.697 - 0.71 @ 15.6潞C (60掳F)
EVAPORATION RATE: >1
POUR POINT: 39.5 掳C (103.1掳F)
SECTION 10 STABILITY AND REACTIVITY
Chemical Stability: This material is considered stable under normal ambient and anticipated storage
and handling conditions of temperature and pressure.
Conditions to Avoid: No Data Available
Incompatibility With Other Materials: May react with oxygen and strong oxidizing agents, such as
chlorates, nitrates, peroxides, etc.
Hazardous Decomposition Products: Carbon Oxides.
Hazardous Polymerization: Hazardous polymerization will not occur.
SECTION 11 TOXICOLOGICAL INFORMATION
IMMEDIATE HEALTH EFFECTS:
Acute Oral Toxicity: LD50 / rat / > 5000 mg/kg
Acute Dermal Toxicity: LD50 / rabbit / > 2000 mg/kg
Acute Inhalation Toxicity: LC50 / rat / 86.46 mg/l / 4 hour(s)
Eye Irritation: This material is irritating to the eyes.
Skin Irritation: This material is not expected to be irritating to the skin.
ADDITIONAL TOXICOLOGY INFORMATION:
This product contains ISOOCTANE.
Genotoxicity: Negative (AMES test, Mouse Lymphoma Assay, Sister Chromatid DNA Exchange, in vivo
dominant, lethal inhalation toxicity)
Developmental/Reproductive: C8 Isoparaffins - Doses (0,400,1200 ppm - 6hr/day, gestation days 6-15)
rat - NOEL >1200 ppm (maternal & developmental toxicity)
Repeat Dose: C8 Isoparaffins - Doses (0,400,1200 ppm - 6hr/5days/wk) rat - NOAEL > 1180 ppm (actual)
SECTION 12 ECOLOGICAL INFORMATION
ECOTOXICITY:
This material is expected to be toxic to aquatic organisms.
- 72 hour(s) / EL50 / algae (Raphidocellus subcapitata ) / 29.0 mg/l
- 96 hour(s) / LL50 / fish (Unidentified species) / 5.4 mg/l
- 48 hour(s) / EL50 / water flea (Daphnia magna ) / 7.4 mg/l
ENVIRONMENTAL FATE:
Biodegradability: 28 day(s) / 74 % volume
This material is expected to be readily biodegradable.
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
5 of 9
Revision Date: 01/25/2005 MSDS : 34750
SECTION 13 DISPOSAL CONSIDERATIONS
Use material for its intended purpose or recycle if possible. This material, if it must be discarded, may
meet the criteria of a hazardous waste as defined by US EPA under RCRA (40 CFR 261) or other State
and local regulations. Measurement of certain physical properties and analysis for regulated components
may be necessary to make a correct determination. If this material is classified as a hazardous waste,
federal law requires disposal at a licensed hazardous waste disposal facility.
SECTION 14 TRANSPORT INFORMATION
The description shown may not apply to all shipping situations. Consult appropriate Dangerous Goods
Regulations, for additional description requirements (e.g., technical name) and mode-specific or quantity-
specific shipping requirements.
Shipping Descriptions per regulatory authority.
US DOT
HYDROCARBONS, LIQUID, N.O.S., 3, UN3295, II
ICAO / IATA
HYDROCARBONS, LIQUID, N.O.S., 3, UN3295, II
IMO / IMDG
HYDROCARBONS, LIQUID, N.O.S., 3, UN3295, II, (-11 掳C )
RID / ADR
UN3295, HYDROCARBONS, LIQUID, N.O.S., 3, II, ADR
SECTION 15 REGULATORY INFORMATION
SARA 311/312 CATEGORIES: 1. Immediate (Acute) Health Effects: YES
2. Delayed (Chronic) Health Effects: NO
3. Fire Hazard: YES
4. Sudden Release of Pressure Hazard: NO
5. Reactivity Hazard: NO
REGULATORY LISTS SEARCHED:
01= CA Prop 65 17 = FDA 178 33 = RCRA Waste Appendix VIII
02 = LA RTK 18 = FDA 179 34 = RCRA Waste D-List
03 = MA RTK 19 = FDA 180 35 = RCRA Waste P-List
04 =MN Hazardous Substance 20 = FDA 181 36 = RCRA Waste U-List
05 =NJ RTK 21 = FDA 182 37 = SARA Section 311/312
06 = PA RTK 22 = FDA 184 38 = SARA Section 313
07 = CAA Section 112 HAPs 23 = FDA 186 39 = TSCA 12 (b)
08 = CWA Section 307 24 = FDA 189 40 = TSCA Section 4
09 = CWA Section 311 25 = IARC Group 1 41 = TSCA Section 5(a)
10 =DOT Marine Pollutant 26 = IARC Group 2A 42 = TSCA Section 8(a) CAIR
11 = FDA 172 27 = IARC Group 2B 43 = TSCA Section 8(a) PAIR
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
6 of 9
Revision Date: 01/25/2005 MSDS : 34750
12 = FDA 173 28 = IARC Group 3 44 = TSCA Section 8(d)
13 = FDA 174 29 = IARC Group 4 45 = WHIMS - IDL
14 = FDA 175 30 = NTP Carcinogen 46 = Germany D TAL
15 = FDA 176 31 = OSHA Carcinogen 47 = Germany WKG
16 = FDA 177 32 = OSHA Highly Hazardous
The following components of this material are found on the regulatory lists indicated.
ISOALKANES 7-8 4
WHMIS CLASSIFICATION:
Class B, Division 2: Flammable Liquids
Class D, Division 2, Subdivision B: Toxic Material
Skin or Eye Irritation
CHEMICAL INVENTORY LISTINGS:
AUSTRALIA: All the components of this material are listed on the Australian Inventory of Chemical
Substances (AICS).
CANADA: This material contains components that are neither on the Domestic Substance List (DSL) nor
on the Non-domestic Substances List (NDSL).
EUROPEAN UNION: All the components of this material are in compliance with the EU Seventh
Amendment Directive 92/32/EEC.
KOREA: All the components of this product are on the Existing Chemicals List (ECL) in Korea.
UNITED STATES: All of the components of this material are on the Toxic Substances Control Act (TSCA)
Chemical Inventory.
PHILIPPINES: This material contains components that require notification before sale or importation into
the Philippines.
JAPAN: All the components of this product are on the Existing & New Chemical Substances (ENCS)
inventory in Japan, or have an exemption from listing.
PEOPLE'S REPUBLIC OF CHINA: This material contains components that require notification before
sale or importation into China.
EU RISK AND SAFETY PHRASES:
R11: Highly flammable.
R36: Irritating to eyes.
R51: Toxic to aquatic organisms.
R65: Harmful: may cause lung damage if swallowed.
R66: Repeated exposure may cause skin dryness or cracking.
S2: Keep out of the reach of children.
S9: Keep container in a well-ventilated place.
S16: Keep away from sources of ignition - No smoking.
S25: Avoid contact with eyes.
S26: In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S51: Use only in well-ventilated areas.
S62: If swallowed do not induce vomiting: seek medical advice immediately and show this container or
label.
EU Symbols: Xn F
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
7 of 9
Revision Date: 01/25/2005 MSDS : 34750
SECTION 16 OTHER INFORMATION
NFPA RATINGS: Health: 1 Flammability: 3 Reactivity: 0 Special: NA
(0-Least, 1-Slight, 2-Moderate, 3-High, 4-Extreme, PPE:- Personal Protection Equipment Index
recommendation, *- Chronic Effect Indicator). These values are obtained using the guidelines or
published evaluations prepared by the National Fire Protection Association (NFPA).
REVISION STATEMENT: This revision updates all sections of the MSDS please review.
ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:
TLV Threshold Limit Value TWA - Time Weighted Average
-
STEL Short-term Exposure Limit PEL - Permissible Exposure Limit
-
ACGIH American Conference of OSHA - Occupational Safety & Health
- Government
Industrial Hygienists
NIOSH National Institute of Safety & Health NFPA - National Fire Protection Agency
-
WHMIS Workplace Hazardous Materials IARC - Intl. Agency for Research on Cancer
- Information System
EINECS European Inventory of existing RCRA - Resource Conservation Recovery Act
- Commercial Chemical Sales
SARA Superfund Amendments and TSCA - Toxic Substance Control Act
- Reauthorization Act.
EC50 Effective Dose LC50 - Lethal Concentration
-
LD50 Lethal Dose CAS - Chemical Abstract Service Number
-
NDA No Data Available NA - Not Applicable
-
<= Less Than or Equal To >= - Greater Than or Equal To
-
CNS Central Nervous System MAK - Germany Maximum Concentration Values
-
This data sheet is prepared according to the latest adaptation of the EEC Guideline 67/548.
This data sheet is prepared according to the OSHA Hazard Communication Standard (29 CFR
1910.1200).
This data sheet is prepared according to the ANSI MSDS Standard (Z400.1).
This data sheet was prepared by EHS Product Stewardship Group, Chevron Phillips Chemical
Company LP, 10001 Six Pines Drive, The Woodlands, TX 77380.
The above information is based on the data of which we are aware and is believed to be correct as
of the date hereof. Since this information may be applied under conditions beyond our control and
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
8 of 9
Revision Date: 01/25/2005 MSDS : 34750
with which we may be unfamiliar and since data made available subsequent to the date hereof may
suggest modifications of the information, we do not assume any responsibility for the results of its
use. This information is furnished upon condition that the person receiving it shall make his own
determination of the suitability of the material for his particular purpose.
______________________________________________________________________
Revision Number: 3 SOLTROL 庐 10
9 of 9
Revision Date: 01/25/2005 MSDS : 34750
|