MATERIAL SAFETY DATA SHEET
SUPCO MO44
DIVERSITECH
HAZARD RATINGS
RUST BREAKER
HMIS DATA
CATALOG NO. CR-1 HEALTH = 1 0 = NONE
FIRE = 1 1 =SLIGHT
REACTIVITY = 0 2 = MODERATE
SECTION I-IDENTIFICATION
3 = HIGH
4 = EXTREME
DISTRIBUTED BY: S U P C O
DIVERSITECH, Inc. PERSONAL PROTECTION INDEX = B
ADDRESS: 2530 Lantrac Landmark Place
2230 Court
Decatur, Georgia 30035 08720
Allenwood, NJ
EMERGENCY Phone No. 800-255-3924 Chem-Tel (Chemical Emergencies Only)
PHONE NUMBER FOR INFORMATION: 770-593-0900 Fax: 770-593-8600
DATE REVISED: 15 October 2002
NAME OF PREPARER: ANTHONY E. JERNIGAN
SECTION II HAZARDOUS INGREDIENTS INFORMATION
INGREDIENT CAS NO OSHA ACIGH OTHER % or
PEL TLV STEL RNG
Aromatic Petroleum Naptha 64742-47-8 No data No data >80
3 3 3
Aromatic Petroleum Naptha 64742- 30-9 5 mg/m (mist) 5 mg/m (mist) 10 mg/m (mist) <20
EPA HAZARD CATEGORIES: None
SECTION III 鈥? PHYSICAL/CHEMICAL CHARACTERISTICS
Specific gravity (H2O = 1): 0.85
Boiling Point: >350掳F
Vapor pressure (mm Hg): 0.01 @20掳C Melting Point(Pour Point):Not applicable
Vapor Density (Air=1): 1.4 Evaporation Rate (Water = 1): Not applicable
Solubility in water: Insoluble in water
Appearance and odor: Clear amber liquid; bland odor.
SECTION IV- FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): >200掳F (COC) Flammable Limits: LEL: N/A UEL: N/A
Extinguishing media: Dry chemical, CO2 , foam, water fog
Special Fire Fighting Procedures: FIREFIGHTERS SHOULD WEAR NIOSH/MNSA APPROVED SELF-
CONTAINED BREATHING APPARATUS AND FULL PROTECTIVE GEAR WHEN FIGHTING FIRES
INVOLVING THIS PRODUCT. Keep containers cooled with a water spray if involved in a fire
Unusual Fire and Explosion Hazards: Burning fluid may evolve irritating/noxious fumes and dense smoke.
Water may cause frothing or splattering when used as an extinguishing agent.
SECTION V 鈥? REACTIVITY DATA
Stability-Stable
Conditions to avoid: Excessive heat; formation of oil mist.
Incompatibility (Materials to avoid): Strong oxidizers, strong alkalis, strong acids, compressed oxygen
Hazardous Decomposition or Byproducts: Carbon monoxide, carbon dioxide, and other unidentified
fragments when burned.
Hazardous Polymerization: Will not occur.
Page 1 of 3
Rust Breaker MSDS
SECTION VI鈥? HEALTH HAZARD DATA
Routes of Entry: Inhalation: yes Skin: yes Ingestion: yes Eyes: yes
Health Hazards (acute and chronic): Short- term contact with skin is not expected to result in adverse
effects. Prolonged skin contact may cause mild defatting or local discomfort. Eye contact may result in
temporary irritation. Prolonged breathing of oil mists may cause pneumonitis, irritation of nose and throat,
headache, nausea or drowsiness.
Carcinogenicity: NTP? no IARC Monographs? no OSHA Regulated? No
Signs and symptoms of exposure:
Inhalation: If sprayed or misted may cause chemical pnuemonitis. This product is not toxic by
inhalation.
Skin: Minimally irritating. Prolonged contact may cause dermatitis, redness or defatting.
Ingestion: Do not take internally. Low toxicity on ingestion. May cause nausea or diarrhea.
Eyes: May cause eye temporary irritation or discomfort.
Medical Conditions Aggravated by Exposure: Contact or breathing mists may exacerbate existing skin or
respiratory disorders. See Health Hazards section above.
Emergency and First Aid Procedures:
Eyes: Flush with water for 15 minutes. Consult a physician if irritation persists
Skin: Remove contaminated clothing. Wash the affected area with soap and water. Launder or dry
clean clothes before reuse. Discard contaminated leather articles.
Inhalation: Evacuate to a safe area with plenty of fresh air. Allow the affected individual to rest in a well
ventilated area. Seek medical aid if symptoms persist.
Ingestion: If more than several ounces of material are swallowed, DO NOT induce vomiting. Give two
16 ounce glasses of water and get medical attention.
SECTION VII 鈥? PRECAUTIONS FOR SAFE HANDLING AND STORAGE
STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED:
Wear recommended protective clothing. Remove contaminated garments promptly. Remove unnecessary
personnel from the area. Floors may be slippery; use care to avoid falling. Contain the spill by diking if
possible. Absorb the liquid with an inert absorbent such as sand, dirt, vermiculite or 鈥渙il-dri鈥?, or use
commercial oil absorbent pads. Transfer liquids and solid diking material to suitable containers, and dispose
of in accordance with local, state, and federal regulations.
DO NOT contaminate municipal sewers or other open bodies of water with runoff.
WASTE DISPOSAL METHODS: Incinerate this material and all associated wastes in accordance with
governmental regulations. Dispose of empty containers in a safe and environmentally responsible manner.
HANDLING AND STORAGE:
Avoid contact with skin and eyes. Keep containers closed when not in use. Store in a dry, cool, well-
ventilated area. Empty containers retain residue and can be dangerous. All containers should be disposed
of in an environmentally safe manner, and in accordance with all governmental regulations.
Keep this and all chemicals out of the reach of children.
SECTION VIII 鈥? CONTROL MEASURES
Respiratory Protection (Specify Type): Use in a well-ventilated area. If mist is being generated and exceeds
the TLV, a respiratory program meeting OSHA 1910.134 and ANSI Z88.2 requirements must be followed.
Ventilation: Local exhaust is recommended when used in enclosed areas.
Protective Gloves: Neoprene, nitrile, or other materials may be used if there is documented evidence of
compatibility may be used as necessary to limit contact hazards.
Eye protection: Safety glasses (ANSI Z87.1) or approved equivalent.
Other Protective Clothing: Neoprene aprons, overshoes, oversleeves or other impervious clothing as
necessary to minimize exposure.
Work Hygienic Practices: Use proper industrial hygiene practices to minimize hazardous exposure. Wash
hands after handling this material, and before eating or smoking.
Page 2 of 3
Rust Breaker MSDS
SECTION IX 鈥? ADDITIONAL INFORMATION
Transportation Information:
DOT HAZARD LABEL: None
TSCA: All ingredients are TSCA approved.
SARA TITLE III Reporting Requirements:
Section 302: EHS reporting not required
Section 304: Hazardous releases reporting not required
Section 311: Community Right To Know reporting is required if the inventory is above the Threshold
Planning Quantity
Section 312: R-T-K Inventory data reporting required for inventory above the TPQ
Section 313: Emissions and release reporting may be required for users of this product within the
manufacturing sector. This does not apply to service companies.
CAUTION: Misuse of empty containers can be hazardous. Empty containers can
be hazardous if used to store toxic, flammable, or reactive materials. Cutting or welding of empty
containers might cause fire, explosion or toxic fumes from residues. Do not pressurize or expose to open
flame or heat. Keep container closed and drum bungs in place.
THE INFORMATION CONTAINED HEREIN IS BELIEVED TO BE ACCURATE. IT IS PROVIDED
INDEPENDENTLY OF ANY SALE OF THE PRODUCT FOR PURPOSE OF HAZARD
COMMUNICATION AS PART OF THE PRODUCT SAFETY PROGRAM. IT IS NOT INTENDED TO
CONSTITUTE PERFORMANCE INFORMATION CONCERNING THE PRODUCT. NO EXPRESS
WARRANTY, OR IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE IS MADE WITH RESPECT TO THE PRODUCT OR THE INFORMATION CONTAINED
HEREIN. DATA SHEETS ARE AVAILABLE FOR ALL PRODUCTS. YOU ARE URGED TO OBTAIN
DATA SHEETS FOR ALL PRODUCTS YOU BUY, PROCESS, USE OR DISTRIBUTE AND YOU
ARE ENCOURAGED AND REQUESTED TO ADVISE THOSE WHO MAY COME IN CONTACT WITH
SUCH PRODUCTS OF THE INFORMATION CONTAINED HEREIN.
Page 3 of 3
|