Pure, Undiluted Paintable Bulk Mold Release
IMS Company Page 1 of 4
May 11, 2001 L-0092A
Material Safety Data Sheet
Section 1 - Manufacturer Information
Manufacturer/Distributor IMS Company Emergency Phone # 800-424-9300
10373 Stafford Road Prepared by Safety Advisor
Chagrin Falls, OH 44023-5296 Prepared/Revised May 11, 2001
Trade Names .........Pure, Undiluted Paintable B ulk Mold Release
Part Number........100513 5 gallon pail Replaces AER3-UBP-1G
100548 1 gallon pail Replaces AER3-UBP-5G
Hazardous Material Information System
Health.................1 Flammability.............1 Reactivity ..................0 Protection .................X
* Chronic (Accumulates)
0 Normal use Material 0 Will Not Burn 0 Stable X = Consult the
1 Slight Hazard (temporary) 1 Possible to Burn 1 Unstable if Heated MSDS and
2 Health Affected (lengthy) 2 Burns if Heated 2 Violent Chemical Change your supervisor
3 Extreme Danger 3 Easily Burns 3 Shock and Heat Sensitive for your special
4 Severe or Fatal 4 Very Easily Burns 4 May Explode workplace need
NOTE The HMIS may not be enough hazard information for this chemical in all workplaces. The HMIS system
requires employee training about the system and about information in this MSDS.
Section 2 - Ingredients
Chemical/Common Name CAS-Number % PEL-OSHA TLV-ACGIH
Paintable Fluid - Organo Modified
(1) (1)
Polysiloxane 68037-77-4 100
(1)
None Established.
Does this product contain carcinogens (NTP, IARC, or OSHA)? No
Section 3 - Health Data
HEALTH EFFECTS - (Acute and Chronic)
Inhalation No injury is likely from relatively short exposures to vapor, of less than eight hours. If used in a
manner that produces a mist, we recommend that exposure limits similar to petroleum oil be
observed, 5mg/m 3.
Ingestion Small amounts transferred to the mouth by fingers during use, etc. should not injure. Swallowing
large amounts may cause digestive discomfort. Consult a physician.
Eyes Direct contact may cause temporary eye irritation, with discomfort.
Skin A single prolonged exposure (24 to 48 hours) causes no known adverse effect. Repeated or
prolonged exposure may cause irritation.
PRIMARY ROUTES OF ENTRY
Inhalation, if used in a manner that causes the fluid to atomize. Transfer to eye from fingers or by contact with
atomized material.
Pure, Undiluted Paintable Bulk Mold Release
IMS Company Page 2 of 4
May 11, 2001 L-0092A
Material Safety Data Sheet
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE None known to us.
EMERGENCY FIRST AID PROCEDURES
Eye Contact Flush eyes immediately with water for at least 15 minutes. May cause temporary eye irritation.
Contact physician.
Skin Contact Do not apply directly to skin. Remove contaminated clothing and shoes. Wash exposed area with
soap and water. Wash contaminated clothing before re-use.
Inhalation Due to the low vapor pressure of this product, it is not an inhalation hazard when handled as a liquid
at ambient temperature. We believe that when the material is atomized, exposure should be limited
to that of an oil mist (5mg/m 3). Otherwise, a protective vapor mask should be used.
Ingestion An unlikely route of entry. However, if ingested, **Get Medical Help At Once**.
Section 4 - Chemical Data
Boiling Point.......................................95掳 F Specific Gravity (Water = 1) .................... 1.006
Vapor Pressure (mmHg)) ..................NA Percent Volatile by Volume (%)............... NA
Vapor Density (Air = 1) ......................NA Evaporation Rate (NA = 1) ...................... NA
Solubility in Water..............................Insoluble
Appearance and Odor Information Colorless liquid and characteristic odor.
Section 5 - Physical Data
Flash Point (Pensky-Martens CC)...................>214掳 F Flammable Limits LEL = NA UEL = NA
Extinguishing Media Dry chemical, water spray and fog, foam carbon dioxide.
Special Fire Fighting Procedures
Wear self-contained, full facepiece, positive-pressure breathing apparatus when fighting fires. Suggested for all fires
involving chemicals. Under fire conditions, irritating and/or toxic vapors, or gases, including benzene, may be
present.
Unusual Fire and Explosion Hazards None known.
Incompatibility (Materials to Avoid) Strong oxidizing agents.
Hazardous Decomposition Products
Carbon monoxide, carbon dioxide, oxides of silicon (SiOx), benzene, hydrogen.
Will Hazardous Polymerization Occur? No
Conditions to Avoid for Polymerization NA
Is the Product Stable? Yes
Conditions to Avoid for Stability NA
Section 6 - Spill or Leak Procedures
Pure, Undiluted Paintable Bulk Mold Release
IMS Company Page 3 of 4
May 11, 2001 L-0092A
Material Safety Data Sheet
Steps to be Taken in Case Material is Released or Spilled
Determine whether to evacuate or isolate the area according to your emergency plan. Observe all personal
protection equipment recommendations described in this MSDS. For large spills, provide diking, or other appropriate
containment to keep material from spreading. If diked material can be pumped, store recovered material in
appropriate container. Clean up remaining materials from spill with suitable absorbant. Clean area as appropriate
since some silicone materials, even in small quantities, may present a slip hazard. Final cleaning may require use of
steam, solvents, or detergents. Dispose of saturated absorbant or cleaning materials appropriately, since
spontaneous heating may occur. Local, state, and federal laws and regulations may apply to releases and disposal
of this material, as well as those materials and items employed in the cleanup of releases.
Wear appropriate personal protective equipment for the conditions and safety glasses as a minimum. Collect
material and place in marked containers. Use caution where spills have occurred due to slipping hazard. Clean
area in order to reduce slip hazard. Use appropriate caution regarding the handling of cleaning solvents/materials.
EPA waste designation is D003, Reactive, under 40 CFR 261.
Waste Disposal Methods
Recovered liquids may be sent to a licensed reclaimer or incineration facility. Contaminated material must be
disposed of in a permitted waste management facility. Consult Federal, State, or Local disposal authorities for
approved procedures.
Section 7 - Exposure Control Information
Ventilation
General ventilation, local exhaust, or mechanical or special ventilation to maintain product and its components below
their exposure limits. See 鈥淎dditional Comments鈥? for ventilation impact if product is heated.
Respiratory Protection
Generally not required when handled at normal work area temperatures. If atomized or subjected to high heat, a
mask suitable for protection against any solvent used to dilute the product and the silicone oil mist must be used.
Consult safety equipment supplier. See 鈥淎dditional Comments鈥? for high heat precautions.
Protective Gloves
Wear solvent-resistant gloves such as Viton, Polyvinyl Alcohol, or equivalent where prolonged or repeated contact
with the spray mist or deposited product is likely.
Other Protective Equipment
Eye protection of safety glasses as a minimum is recommended. Chemical Monogoggles or safety glasses with side
shields and a face shield will provide protection in most situations. Do not wear contact lenses.
Other Engineering Controls
To determine exposure levels, monitoring should be performed. This is especially important if the product is heated
above 300潞 F, which can cause the formation of benzene. See 鈥淎dditional Comments.鈥?
Work Practices
If diluted with solvent DO NOT use in confined or closed space. Ventilation should maintain the concentration of the
product and its components below their exposure limits and the concentration of silicone oil below 5 mg/m3.
Hygienic Practices
Avoid contact with skin and avoid breathing vapors. Do not eat, drink, or smoke in work area. Wash hands before
eating, drinking, or using restroom after using this or any chemical product.
Section 8 - Special Precautions
Pure, Undiluted Paintable Bulk Mold Release
IMS Company Page 4 of 4
May 11, 2001 L-0092A
Material Safety Data Sheet
Precautions to be Taken in Handling and Storage
Store this and all industrial chemicals away from food and beverages. Store in a cool dry area away from
incompatible materials.
Maintenance Precautions Do not remove or deface label.
Other Precautions
Clean up spills promptly to minimize slipping hazard. Please read and follow directions and cautions on the label
and any accompanying literature.
Additional Comments
NOTICE
Note: These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray
application may require added precautions.
Traces of benzene (carcinogen) may form if heated in air above 300掳 F (149掳C). Provide ventilation to control vapor
exposure within inhalation guidelines when handling at elevated temperatures. Review the OSHA benzene
regulation for tailed information on safe handling requirements.
CAUTION Intentional misuse of this chemical product, as with any industrial chemical, in contact with the
body can be harmful or fatal. This includes such things as deliberately breathing, placing in mouth,
swallowing, placing on skin, or any other body contact, or repeated, or continuous contact.
IMS provides this information in good faith, but makes no representation as to its comprehensiveness or its
accuracy. This document is offered as a guide to a trained person, for appropriate precautionary handling. Persons
using the product and receiving the information must exercise independent judgment in determining the
appropriateness of the use and the safety information for their particular purpose. IMS MAKES NO
REPRESENTATIONS OR WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS
INFORMATION OR TO THE PRODUCT. ACCORDINGLY, IMS WILL NOT BE RESPONSIBLE FOR DAMAGES
RESULTING FROM USE OF OR RELIANCE ON THIS INFORMATION.
|