IMS Company Overnight Mold Protector (tank) Page 1 of 4
Material Safety Data Sheet
June 14, 2007
Section 1 - Manufacturer Information
IMS Company Emergency Phone 800-424-9300
Manufacturer
10373 Stafford Road Prepared by Product Safety Advisor
Chagrin Falls, OH 44023-5296 Prepared/Revised June 8, 2007
WEB: imscompany.com E-mail sales@imscompany.com
Trade Name .......... Overnight Mold Protector (tank) (not for Aluminum molds)
Item Number ......... 121764 28 pound (net) tank Replaces AEM2-MP30-B
Hazardous Material Information System
Health ................3* Flammability.............1 Reactivity ................. 1 Protection................. X
* Chronic (Accumulates)
0 Normal use Material 0 Will Not Burn 0 Stable X = Consult the
1 Slight Hazard (temporary) 1 Possible to Burn 1 Unstable if Heated MSDS and
2 Health Affected (lengthy) 2 Burns if Heated 2 Violent Chemical Change your supervisor
3 Extreme Danger 3 Easily Burns 3 Shock and Heat Sensitive for your special
4 Severe or Fatal 4 Very Easily Burns 4 May Explode workplace need
NOTE: The HMIS may not be enough hazard information for this chemical in all workplaces. The HMIS system
requires employee training about the system and about information in this MSDS.
Section 2 - Hazardous Ingredients
Chemical/Common Name CAS-Number % PEL-OSHA TLV-ACGIH
Carbon Dioxide 124-38-9 5 to 10 5000 ppm 5000 ppm
Trichloroethylene (2) (5) 79-01-6 70 to 90 100 ppm 50 ppm
5mg/M3 (3) 5mg/M3 (3)
Petroleum Lubricating Oil 64742-65-0 0.1 to 10
Ethylene Glycol Monobutyl Ether (2) 25 ppm (4)
111-76-2 0.1 to 10 50 ppm
Zinc Dinonylnaphthalenesulfonate (2) (1) (1)
28016-00-4 0.1 to 10
(1) (1)
Calcium Dinonylnaphthalenesulfonate 57855-77-3 0.1 to 10
(1)
Not Established
(2)
Material subject to SARA Title III Sec. 313 reporting requirements.
(3)
For Oil Mist
(4)
For Skin Contact
(5)
WARNING: This product contains a chemical known to the State of California to cause cancer, or birth
defects, or other reproductive harm.
Does this product contain carcinogens according to NTP, IARC, or OSHA? Yes
Petroleum Lubricating Oil 64742-65-0 IARC 2A, Group 1, NTP
Trichloroethylene 79-01-6 OSHA - A5, IARC 鈥? A2, NTP - suspected
IMS Company Overnight Mold Protector (tank) Page 2 of 4
Material Safety Data Sheet
June 14, 2007
Section 3 - Health Hazard Data
HEALTH EFFECTS - (Acute and Chronic):
FATAL OR HARMFUL IF INHALED Nasal and respiratory irritation. Central Nervous
Inhalation:
System (CNS) depression including dizziness, fatigue, nausea, headache, possible
unconsciousness, and even death with gross overexposure.
Single dose toxicity is believed to be low to moderate. If vomiting occurs, product could be
Ingestion:
aspirated into the lungs, which could cause chemical pneumonia and systemic effects.
Liquid can cause slight temporary irritation with slight temporary corneal injury. Vapors can
Eyes:
irritate eyes.
Prolonged or repeated skin contact can cause irritation, defatting of skin, and dermatitis.
Skin:
Absorption of liquid through intact skin possible, resulting in systemic effects, but unlikely
route of significant exposure. This product contains metal sulfonates. Sulfonates have
potential to cause allergic skin reaction.
The findings of chronic toxic effects in lab animals overexposed to components of this
Chronic:
product indicate toxicity to humans. Over-exposure should be avoided. Failure to do so
could result in injury, illness, or even death. Chronic overexposures to Trichloroethylene can
cause damage to liver, kidney, brain, nerves, lungs.
PRIMARY ROUTES OF ENTRY Inhalation, skin
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE Acute and chronic liver disease and rhythm
disorders of the heart may be aggravated by overexposure. Dermatitis may be aggravated by contact.
EMERGENCY FIRST AID PROCEDURES
Flush eyes immediately with water for at least 15 minutes. Call a physician.
Eye Contact:
Remove contaminated clothing and shoes immediately. Wash exposed area with soap
Skin Contact:
and water for at least 15 minutes. Wash contaminated clothing before re-use.
Remove to fresh air. If breathing has stopped, administer artificial respiration.
Inhalation:
**Get Medical Help at once**
Do not induce vomiting. **Get Medical Help at once**
Ingestion:
**Note to Medical Personnel**
Because of increased risk of disturbances of cardiac rhythm, Catecholamine drugs such as
Epinephrine, Adrenalin, etc. should be used only with special caution and only in situations of
emergency life support. Consider gastric lavage for ingestion. Consider oxygen for inhalation.
IMS Company Overnight Mold Protector (tank) Page 3 of 4
Material Safety Data Sheet
June 14, 2007
Section 4 - Chemical Data
Boiling Point (F) ............................. ~189潞 F Specific Gravity (Water=1) ................ > 1
Vapor Pressure (PSIG).................. 130 卤 20 Percent Volatile by Volume (%) ........ > 80
Vapor Density (Air=1) .................... > 1 Evaporation Rate (Ether) .................. > faster
Solubility in Water..........................Slight Melting point...................................... -99潞 F
Appearance and Odor Information Clear to yellow mist with the odor of chlorinated solvent ( a mildly
sweet odor) as dispensed from the aerosol.
Section 5 - Physical Hazard Data
Flash Point (Method Used)....................... None (TCC) Flammable Limits : LEL=1.1% UEL=52%
LEL/UEL based on of components
Autoignition temperature ..........................770潞 F (410潞 C)
CONTENTS UNDER PRESSURE
Extinguishing Media Foam, dry chemical, carbon dioxide, and water fog. Because product is essentially
non-flammable, media to control fire in surrounding materials is important.
Special Fire Fighting Procedures At elevated temperatures (above 120潞飥? F), pressurized containers may
burst, vent, or rupture. Use equipment or shielding to protect personnel against bursting, rupturing, or
venting containers. Cooling with water streams may be helpful.
Unusual Fire and Explosion Hazards Concentrated vapors can be ignited by high intensity ignition
source. Firefighters should wear self-contained, positive-pressure breathing apparatus, due to combustion
products, and should avoid skin contact.
Incompatibility (Materials to Avoid) Strong alkalies, oxidizers, and reactive metals (e.g., Aluminum,
Potassium, Sodium, Zinc, Magnesium).
Hazardous Decomposition Products Hydrogen chloride, phosgene, chlorine, carbon dioxide, carbon
monoxide, and hydrocarbon products would be expected.
Will Hazardous Polymerization Occur? No
Conditions to Avoid for Polymerization: NA
Is the Product Stable? Yes
Conditions to Avoid for Stability Avoid contact with open flame, electric arcs, or other hot surfaces that
can cause combustion. Avoid temperatures high enough to rupture container (above 120潞飥? F).
IMS Company Overnight Mold Protector (tank) Page 4 of 4
Material Safety Data Sheet
June 14, 2007
Section 6 - Spill or Leak Procedures
Steps to be Taken in Case Material is Released or Spilled Evacuate the area. Avoid breathing vapors.
Remove sources of ignition. Ventilate area to reduce concentration of the components below their
TLV/PEL values. Use personal protective equipment consistent with the situation. Pick up the spill on
absorbent material; store in closed containers for proper disposal. Avoid contamination of ground and
surface waters. Do not flush to sewer. If spill occurs indoors, turn off air conditioning and/or heating
system, to prevent vapors from contaminating entire building.
Waste Disposal Methods Consult Federal, State, and Local regulations. When zero pressure, open
valve fully and break off plastic T-handle to keep valve from being closed. Since residue remains when
tank is empty, leave label on. Dispose of tank according to local regulations. Where possible, please
recycle.
Section 7 - Exposure Control Information
Ventilation General ventilation, local exhaust, or mechanical or special ventilation to maintain product and
its components below TLV/PEL. The IDLH for Trichloroethylene is 1000 ppm.
Respiratory Protection Generally not required if adequate ventilation is provided. If the TLV/PEL of any
component is exceeded, a NIOSH approved organic and inorganic vapor mask should be used (consult
your safety equipment supplier). Above 1000 ppm for Trichloroethylene, an approved, self-contained
breathing apparatus, or airline respirator with full face-piece is required.
Protective Gloves Wear solvent-resistant gloves such as Viton, Polyvinyl Alcohol, or equivalent where
prolonged or repeated contact with the spray mist or deposited product is likely.
Other Protective Equipment As required by your company. If contact with the spray is likely, eye
protection is recommended. Goggles or safety glasses with side shields and a face shield will provide
protection in most situations. Do not wear contact lenses.
Other Engineering Controls To determine exposure levels, monitoring should be performed. Eyewash
station should be available.
Work Practices Do not use in confined or closed space. Ventilation should maintain the concentration of
the product or its components below their TLV/PEL values.
Hygienic Practices Avoid contact with skin and avoid breathing vapors. Do not eat, drink, or smoke in
work area. Wash hands before eating, drinking, or using restroom after using this or any chemical product.
Section 8 - Special Precautions
Precautions to be Taken in Handling and Storage Store in cool, dry area out of direct sunlight (below
120潞飥? F). Do not puncture or burn containers. Give empty, leaking, or full containers to a disposal service
equipped to handle and dispose of pressurized containers.
Maintenance Precautions Do not remove or deface label.
Other Precautions Vapors are heavier than air and will collect in low areas. Read and follow directions
and cautions on the container label, and any accompanying literature.
|