Sartomer Company
Material Safety Data Sheet
Product: SR833S Revised Date: 01-17-2005
MSDS ID: S-001137 Replaces Date: 06-06-2001
01. GENERAL INFORMATION
Sartomer Company, Inc.
Oaklands Corporate Center
502 Thomas Jones Way
Exton, Pennsylvania 19341
Emergency phone numbers:
800/424-9300 (CHEMTREC)
610/692-8401 (Sartomer Co., Inc.)
Product information:
610/363-4100
GENERIC NAME
Acrylate Ester Tricyclodecane Dimethanol Diacrylate
DOT PROPER SHIPPING NAME UN/NA NUMBER
N/AP N/AP
DOT HAZARD CLASS
Not regulated
02. SUMMARY OF HAZARDS
WARNING
PHYSICAL HAZARDS: Unstable (reactive) upon depletion of inhibitor
ACUTE HEALTH EFFECTS: Slight eye irritant
(SHORT-TERM) Slight skin irritant
Suspect skin sensitization hazard
Suspect slight skin absorption hazard
Suspect respiratory tract irritation hazard
Suspect slight ingestion hazard
CHRONIC HEALTH EFFECTS: No chronic health effects data is available for
(LONG-TERM) this material.
03. COMPONENTS
COMPONENT NAME CAS NUMBER % COMPOSITION (BY WT.)
Tricyclodecane Dimethanol Diacrylate 42594-17-2 AP 100
04. PHYSICAL AND CHEMICAL DATA
BOILING POINT pH
N/DA 6.8-7.2
FREEZING POINT DRY POINT
N/DA N/DA
SPECIFIC GRAVITY (H20=1 AT 39.2F) VOLATILE CHARACTERISTICS
1.08-1.12 at 25C/77F Negligible
VISCOSITY UNITS, TEMP. (Brookfield) SOLUBILITY IN WATER
AP 100-250 cps at 25C/77F Insoluble
VAPOR PRESSURE STABILITY
N/DA Stable
Date Printed: 01-17-2005 Page: 1 of 7
Sartomer Company
Material Safety Data Sheet
Product: SR833S Revised Date: 01-17-2005
MSDS ID: S-001137 Replaces Date: 06-06-2001
VAPOR SP GR (AIR=1 AT 60 - 90F) HAZARDOUS POLYMERIZATION
N/DA May occur
APPEARANCE AND ODOR
Light yellow, viscous liquid with faint odor
CONDITIONS AND MATERIALS TO AVOID
High temperatures, localized heat sources (ie, drum or band heaters),
oxidizing conditions, freezing conditions, direct sunlight, ultraviolet
radiation, inert gas blanketing;
Strong oxidizers, strong reducers, strong acids and bases, free radical
initiators, inert gases, oxygen scavengers
HAZARDOUS DECOMPOSITION PRODUCTS
Acrid smoke-fumes/carbon monoxide/carbon dioxide and perhaps other toxic
vapors may be released during a fire involving this product.
05. OCCUPATIONAL EXPOSURE LIMITS
SUBSTANCE SOURCE DATE TYPE VALUE TIME
A PEL or TLV has not been established
06. FIRE AND EXPLOSION
FLASH POINT METHOD=(Estimated) AUTOIGNITION TEMP. METHOD=
GT 93C/200F N/DA
FLAMMABLE LIMITS (% VOLUME IN AIR)
LOWER: N/DA UPPER: N/DA
FIRE AND EXPLOSION HAZARDS
High temperatures, inhibitor depletion, accidental impurities, or exposure to
radiation or oxidizers may cause spontaneous polymerizing reaction generating
heat/pressure. Closed containers may rupture or explode during runaway
polymerization.
EXTINGUISHING MEDIA
Dry chemical
CO2
Foam
Use water spray/water fog for cooling
SPECIAL FIREFIGHTING PROCEDURES
Do not enter fire area without proper protection. See Section 4 -
decomposition products possible. Fight fire from safe distance/protected
location. Heat/impurities may increase temperature/build pressure/rupture
closed containers, spreading fire, increasing risk of burns/injuries. Water
may be ineffective in firefighting due to low solubility. Use water
spray/fog for cooling. Pressure relief system may plug with solids,
increasing risk of overpressure. Notify authorities if liquid enters
sewer/public waters.
Date Printed: 01-17-2005 Page: 2 of 7
Sartomer Company
Material Safety Data Sheet
Product: SR833S Revised Date: 01-17-2005
MSDS ID: S-001137 Replaces Date: 06-06-2001
07. HEALTH HAZARDS
ROUTES OF EXPOSURE
INHALATION
No significant signs or symptoms indicative of any adverse health hazard are
expected to occur at standard conditions due to the low volatility of this
material. However, aerosols, or vapors which may be generated at elevated
processing temperatures, may cause respiratory tract irritation. Symptoms of
irritation may include coughing, mucous production and shortness of breath.
EYE CONTACT -- PRIMARY ROUTE
May cause minor eye irritation. Symptoms may include excessive tearing,
blinking and redness.
SKIN ABSORPTION -- PRIMARY ROUTE
Although no appropriate human or animal health effects data are known to
exist, this material is expected to be a health hazard by skin absorption.
SKIN IRRITATION -- PRIMARY ROUTE
May cause minor skin irritation.
Symptoms may include a slight localized redness or rash and swelling.
However, this material may cause skin sensitization (an allergic skin
reaction) upon repeated exposures.
INGESTION
Although no appropriate human or animal health effects data are known to
exist, this material is expected to be a slight ingestion hazard.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
No additional medical information found.
08. PROTECTIVE EQUIPMENT / CONTROL MEASURES
RESPIRATORY PROTECTION
If this material is handled at elevated temperature or under mist forming
conditions, NIOSH/MSHA approved respiratory protection equipment should be
used.
EYE PROTECTION
Eye protection such as chemical splash goggles and/or face shield must be
worn when possibility exists for eye contact due to splashing or spraying
liquid, airborne particles, or vapor. Contact lenses should not be worn.
SKIN PROTECTION
Depending on the conditions of use, protective gloves, apron, boots, head
and face protection should be worn. This equipment should be cleaned
thoroughly after each use.
ENGINEERING CONTROLS
Date Printed: 01-17-2005 Page: 3 of 7
Sartomer Company
Material Safety Data Sheet
Product: SR833S Revised Date: 01-17-2005
MSDS ID: S-001137 Replaces Date: 06-06-2001
If handling results in aerosol or vapor generation, local exhaust ventilation
is recommended.
OTHER HYGIENIC PRACTICES
Emergency eye wash fountains and safety showers should be available in the
immediate vicinity of any potential exposure.
OTHER WORK PRACTICES
Use good personal hygiene practices. Wash hands before eating, drinking,
smoking, or using toilet facilities. Promptly remove soiled clothing/wash
thoroughly before reuse. Shower after work using plenty of soap and water.
09. EMERGENCY AND FIRST AID
INHALATION
If overcome by exposure, remove victim to fresh air immediately. Give oxygen
or artificial respiration as needed. Obtain emergency medical attention.
Prompt action is essential.
EYE CONTACT
In case of eye contact, immediately rinse with clean water for 20-30 minutes.
Retract eyelids often. Obtain emergency medical attention if pain, blinking,
tears or redness persist.
SKIN CONTACT
Remove contaminated clothing as needed. Wash skin thoroughly with mild
soap/water. Flush with lukewarm water for 15 minutes. If sticky, use waterless
cleaner first.
INGESTION
If large quantity swallowed, give lukewarm water (pint) if victim completely
conscious/alert. Do not induce vomiting/risk of damage to lungs exceeds
poisoning risk. Obtain emergency medical attention.
EMERGENCY MEDICAL TREATMENT PROCEDURES
Treat symptomatically.
10. SPILL AND DISPOSAL
PRECAUTIONS IF MATERIAL IS SPILLED OR RELEASED
Spilled or released material may polymerize and release heat/gases.
Extinguish all ignition sources and ventilate area. Wear protective
equipment during clean-up. Dike and recover large spill. Soak up small
spill with inert solids (such as vermiculite, clay) and sweep/shovel into
vented disposal container. Wash spill area with a strong detergent and water
solution; rinse with water but minimize water use during clean-up. For
spills on water, contain, minimize dispersion and collect. Dispose/report
per regulatory requirements.
WASTE DISPOSAL METHODS
Non-contaminated, properly inhibited product is not a RCRA hazardous waste.
However, contaminated product/soil/water may be RCRA/OSHA hazardous waste due
Date Printed: 01-17-2005 Page: 4 of 7
Sartomer Company
Material Safety Data Sheet
Product: SR833S Revised Date: 01-17-2005
MSDS ID: S-001137 Replaces Date: 06-06-2001
to potential for internal heat generation (see 40 CFR 261 and 29 CFR 1910).
It is the responsibility of the generator to determine at the time of
disposal whether the product meets the criteria of a hazardous waste. Comply
with all applicable federal, state and local regulations. Use registered
transporters. Disposal options include landfilling solids at permitted
sites; fuel blending or incinerating liquids. Assure emissions comply with
applicable regulations. Dilute aqueous waste may biodegrade; avoid
overloading/poisoning plant biomass. Assure effluent complies with
applicable regulations.
11. ADDITIONAL PRECAUTIONS
HANDLING AND STORAGE PROCEDURES
Wear appropriate protective equipment when handling this material (See Section
8 of MSDS). Most acrylic monomers have low viscosities; hence, pouring,
material transfer and processing of these materials do not necessitate
heating. Viscous monomers may require heating to facilitate handling. To
facilitate product transfer from original container, product may be heated to
60C/140F for not more than 24 hours. Do NOT use localized heat sources such
as band heaters to heat/melt product. Do NOT use steam. Hot boxes or hot
rooms are recommended for heating/melting material. The hot box or hot room
should be set at a maximum temperature of 60C/140F. Do not overheat--this may
compromise product quality and/or result in an uncontrolled hazardous
polymerization. If product freezes, heat as indicated above and mix gently to
redistribute the inhibitor. Product should be consumed in its entirety after
heating/melting--avoid multiple "re-heats" which may affect product quality or
result in product degradation. Product is packaged with inhibitor(s). Unless
inhibited, product can polymerize, raising temperature and pressure possibly
rupturing container. Check inhibitor content periodically, adding to bulk
material if needed. In addition, the product's inhibitor(s) require the
presence of dissolved oxygen. Maintain, at a minimum, the original headspace
in the product container and do not blanket or mix with oxygen-free gas as it
renders inhibitor ineffective. Ensure air space (oxygen) is present during
product heating/melting.
Store product indoors at temperatures greater than product's freezing point
(or greater than 0C/32F if no freezing point available) and below 38C/100F.
Avoid prolonged (longer than shelf-life) storage temperatures above 38C/100F.
Store in tightly closed containers in a properly vented storage area away
from: heat, sparks, open flame, strong oxidizers, radiation, and other
initiators. Prevent contamination by foreign materials. Prevent moisture
contact. Use only non-sparking tools and limit storage time. Unless
specified elsewhere, shelf-life is 6 months from receipt.
Keep in the original container at temperatures not exceeding 35C/95F.
DECONTAMINATION PROCEDURES
Follow standard plant procedures or supervisor's instructions for
decontamination operations.
12. LABEL INFORMATION
USE STATEMENT
Date Printed: 01-17-2005 Page: 5 of 7
Sartomer Company
Material Safety Data Sheet
Product: SR833S Revised Date: 01-17-2005
MSDS ID: S-001137 Replaces Date: 06-06-2001
FOR INDUSTRIAL USE ONLY
SIGNAL WORD
WARNING
PHYSICAL HAZARDS
UNSTABLE (REACTIVE) UPON LOSS OF INHIBITOR
HEALTH HAZARDS
MAY CAUSE ALLERGIC SKIN REACTION
PRECAUTIONARY MEASURES
HAZARDOUS POLYMERIZATION MAY OCCUR UPON DEPLETION OF INHIBITOR.
DO NOT HANDLE NEAR HEAT, SPARKS, OR OPEN FLAME.
DO NOT USE DRUM HEATER TO FACLIITATE HANDLING.
AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
AVOID BREATHING VAPORS/MISTS.
USE ONLY WITH ADEQUATE VENTILATION/PERSONAL PROTECTION.
KEEP CONTAINER CLOSED WHEN NOT IN USE.
WASH THOROUGHLY AFTER HANDLING.
BEFORE USING PRODUCT, READ MATERIAL SAFETY DATA SHEET (MSDS).
13. SUPPLEMENT
NPCA HMIS RATING
Health 1
Flammability 1
Reactivity 2
Personal Protection** D
**Respiratory protection may be necessary depending on conditions of use.
REGULATORY INFORMATION
TSCA STATUS:
TSCA status: All components of this product are listed, or excluded from
listing, on the United States Environmental Protection Agency Toxic Substances
Control Act (TSCA) inventory.
CALIFORNIA PROPOSITION 65:
California Proposition 65 Information: This product contains, or may contain,
trace quantities of a substance(s) known to the state of California to cause
cancer and/or reproductive toxicity.
INTERNATIONAL INVENTORY STATUS
Australia (AICS): included on inventory
Canada (DSL): included on inventory
China : included on inventory
Europe (EINECS): included on inventory
Japan (ENCS): included on inventory
Korea (ECL): included on inventory
Philippines (PICCS): included on inventory
Date Printed: 01-17-2005 Page: 6 of 7
Sartomer Company
Material Safety Data Sheet
Product: SR833S Revised Date: 01-17-2005
MSDS ID: S-001137 Replaces Date: 06-06-2001
This material contains an inhibitor (HQ, MEHQ, etc.) at <1%. The type and
amount meet product specifications. Contact a company representative for
exact concentrations and details on inhibitor level maintenance.
*Note - qualifiers and codes used in this MSDS
EQ = Equal; AP = Approximately; LT = Less Than; GT = Greater Than;
TR = Trace; UK = Unknown; N/AP = Not Applicable; N/P = No Applicable
Information Found; N/DA = No Data Available
14. DISCLAIMERS
Some of the information presented and conclusions drawn herein are from
sources other than direct test data on the product itself. The information in
this MSDS was obtained from sources which we believe are reliable. However,
the information is provided without any warranty, express or implied,
regarding its correctness. The conditions or methods of handling, storage, use
and disposal of the product are beyond our control and may be beyond our
knowledge. For this and other reasons, we do not assume responsibility and
expressly disclaim liability for loss, damage or expense arising out of or in
any way connected with the handling, storage, use or disposal of the product.
This MSDS was prepared and is to be used only for this product. If the
product is used as a component in another product, this MSDS information may
not be applicable. This MSDS has been prepared in accordance with the
requirements of the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Date Printed: 01-17-2005 Page: 7 of 7
|