Sartomer Company
Material Safety Data Sheet
Product: NORSOLENE W-100 Revised Date: 05-03-2005
MSDS ID: S-001363 Replaces Date: 01-17-2005
01. GENERAL INFORMATION
Sartomer Company, Inc.
Oaklands Corporate Center
502 Thomas Jones Way
Exton, Pennsylvania 19341
Emergency phone numbers:
800/424-9300 (CHEMTREC)
610/692-8401 (Sartomer Co., Inc.)
Product information:
610/363-4100
TRADE NAME
Norsolene W Grades: 80, 85, 90, 100, 110
GENERIC NAME
Hydrocarbon Resin
DOT PROPER SHIPPING NAME UN/NA NUMBER
N/AP N/AP
DOT HAZARD CLASS
Not regulated
02. SUMMARY OF HAZARDS
CAUTION
PHYSICAL HAZARDS: Potential dust explosion hazard
ACUTE HEALTH EFFECTS: Slight respiratory tract irritation hazard--
(SHORT-TERM) particulate/dust
Slight eye irritation hazard--particulate/dust
Not a skin irritant based on available data
Not a skin sensitizer based on available data
Not expected to be a skin absorption hazard
Not an ingestion hazard based on available data
CHRONIC HEALTH EFFECTS: No chronic health effects data are known to
(LONG-TERM) exist.
03. COMPONENTS
COMPONENT NAME CAS NUMBER % COMPOSITION (BY WT.)
Hydrocarbon Resin 9011-11-4 AP 100
04. PHYSICAL AND CHEMICAL DATA
BOILING POINT pH
N/AP N/DA
FREEZING POINT SOFTENING RANGE
N/AP 80-110C (176-230F)
Date Printed: 05-03-2005 Page: 1 of 7
Sartomer Company
Material Safety Data Sheet
Product: NORSOLENE W-100 Revised Date: 05-03-2005
MSDS ID: S-001363 Replaces Date: 01-17-2005
SPECIFIC GRAVITY (H20=1 at 39.2F) VOLATILE CHARACTERISTICS
1.05-1.07 at 25C/77F Negligible at 20C/68F
VISCOSITY UNITS, TEMP. SOLUBILITY IN WATER
N/AP Insoluble
VAPOR PRESSURE STABILITY
N/DA Stable
VAPOR SP GR (AIR=1 at 60 - 90F) HAZARDOUS POLYMERIZATION
N/DA Will not occur
APPEARANCE AND ODOR
Translucent, colorless flakes with low typical hydrocarbon odor
CONDITIONS AND MATERIALS TO AVOID
Keep material away from oxidizing agents and out of direct sunlight.
Avoid generating dust when handling this material and prevent electrostatic
charge formation/build up during storage, transfer and handling/use. Avoid
decomposition of material during thermal processing.
HAZARDOUS DECOMPOSITION PRODUCTS
Carbon monoxide, carbon dioxide may be released during thermal decomposition
or in a fire involving this product.
05. OCCUPATIONAL EXPOSURE LIMITS
SUBSTANCE SOURCE TYPE VALUE
No specific occupational exposure standards have been established for this
material. However, airborne concentrations should be kept within the
following limits:
Particulates, OSHA PEL-TWA 15 mg/g3 (Total dust)
not otherwise 5 mg/m3 (Respirable)
classified
ACGIH TLV-TWA 10 mg/m3 (Inhalable)
3 mg/m3 (Respirable)
06. FIRE AND EXPLOSION
FLASH POINT = Closed Cup AUTOIGNITION TEMP.
>250C (482F) N/DA
FLAMMABLE LIMITS (% VOLUME IN AIR)
LOWER: N/AP UPPER: N/AP
FIRE AND EXPLOSION HAZARDS
If a sufficient quantity of finely divided dust is mixed with air and
exposed to an ignition source, it may burn in the open or explode if
confined. Follow good housekeeping practices to avoid rendering dust
airborne and prevent electrostatic charge formation during storage, transfer
and use of this material. Vapors generated from overheating/melting or
decomposition may be flammable and may cause fire/explosion if an ignition
source is present.
Date Printed: 05-03-2005 Page: 2 of 7
Sartomer Company
Material Safety Data Sheet
Product: NORSOLENE W-100 Revised Date: 05-03-2005
MSDS ID: S-001363 Replaces Date: 01-17-2005
EXTINGUISHING MEDIA
Dry chemical
CO2
Water spray
Foam
Water fog
SPECIAL FIREFIGHTING PROCEDURES
Do not enter fire area without proper protection. See section on
decomposition products possible. Fight fire from safe distance/protected
location. Apply aqueous extinguishing media carefully to prevent
frothing/steam explosion. Use water spray/fog for cooling. Avoid contact
with molten product to prevent serious burns. Avoid raising powdered
materials into airborne dust, creating an explosion hazard. Notify
authorities if liquid enters sewer/public waters.
07. HEALTH HAZARDS
ROUTES OF EXPOSURE
INHALATION -- PRIMARY ROUTE
As with other dust generating materials, excessive dust exposure may cause
irritation of the respiratory tract. Symptoms may include cough, sneezing,
mucous production and shortness of breath.
EYE CONTACT -- PRIMARY ROUTE
Particulates/dust entering the eye can cause mechanical irritation. Eyes may
become red, feel scratchy and tear.
SKIN ABSORPTION
Although no appropriate human or animal health effects data are known to
exist, this material is not expected to be a health hazard by skin
absorption.
SKIN IRRITATION -- PRIMARY ROUTE
This material is not expected to cause skin irritation in its original form
(flake) based on available data. However, skin contact with molten product
may cause thermal burns.
This material is not expected to cause skin sensitization (allergic skin
reaction) based on available test data.
INGESTION
No significant signs or symptoms indicative of any adverse health hazard are
expected to occur as a result of ingestion.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
No additional medical information found.
08. PROTECTIVE EQUIPMENT / CONTROL MEASURES
Date Printed: 05-03-2005 Page: 3 of 7
Sartomer Company
Material Safety Data Sheet
Product: NORSOLENE W-100 Revised Date: 05-03-2005
MSDS ID: S-001363 Replaces Date: 01-17-2005
RESPIRATORY PROTECTION
If exposure exceeds the PEL/TLV for nuisance particulate, use NIOSH/MSHA
approved respiratory protection equipment.
Provide ventilation during thermal processing (refer to engineering controls
recommended in this section).
EYE PROTECTION
Dust service goggles should be worn to prevent mechanical injury to eyes due
to airborne particles/dust which may be associated with this product.
Protective goggles should also be worn when thermally processing this
material.
SKIN PROTECTION
Use insulated gloves, impervious apron, long sleeves and other protective
clothing when handling this material hot. Wash clothing frequently.
ENGINEERING CONTROLS
Provide local exhaust or general room ventilation to minimize exposure to
dust. If mechanical ventilation is used, electrical systems should conform to
National Electric Code.
Thermal processing equipment should be properly ventilated to control gases/
vapors which may be evolved. Vapors from thermal processing may be flammable.
OTHER HYGIENIC PRACTICES
Emergency eye wash fountains and safety showers should be available in the
immediate vicinity of any potential exposure.
OTHER WORK PRACTICES
Use good personal hygiene practices. Wash hands before eating, drinking,
smoking, or using toilet facilities. Promptly remove soiled clothing/wash
thoroughly before reuse. Shower after work using plenty of soap and water.
09. EMERGENCY AND FIRST AID
INHALATION
If overcome by exposure, remove victim to fresh air and obtain emergency
medical attention. Give oxygen or artificial respiration as needed.
EYE CONTACT
In case of eye contact, immediately rinse with clean water for 20-30 minutes.
Retract eyelids often. Obtain emergency medical attention if pain, blinking,
tears or redness persist.
SKIN CONTACT
Remove contaminated clothing as needed. Wash skin thoroughly with mild
soap/water. Flush with lukewarm water for 15 minutes. If sticky, use waterless
cleaner first.
In case of skin contact with molten product, flood affected areas with cool
Date Printed: 05-03-2005 Page: 4 of 7
Sartomer Company
Material Safety Data Sheet
Product: NORSOLENE W-100 Revised Date: 05-03-2005
MSDS ID: S-001363 Replaces Date: 01-17-2005
water for 15 minutes. Do not attempt to remove adhered material from skin.
Obtain emergency medical attention.
INGESTION
Not expected to present a significant ingestion hazard under anticipated
conditions of normal use. However, if ingested, give lukewarm water (pint) if
victim completely conscious/alert. Do not induce vomiting. Obtain emergency
medical attention.
10. SPILL AND DISPOSAL
PRECAUTIONS IF MATERIAL IS SPILLED OR RELEASED
Material can create slipping hazard on any hard surface. Remove spilled
material immediately from hard, smooth walking surfaces. Sweep/shovel
contaminated material into suitable disposal containers. Report per
regulatory requirements.
WASTE DISPOSAL METHODS
When discarded in its purchased form, this product is not a RCRA hazardous
waste. However, it is the responsibility of the generator to determine at
the time of disposal whether the product meets the criteria of a hazardous
waste. Comply with all applicable federal, state and local regulations.
Waste disposal options include landfilling solids at permitted sites. Use
registered transporters.
11. ADDITIONAL PRECAUTIONS
HANDLING AND STORAGE PROCEDURES
Store material in a cool, dry place. Keep away from sparks and open flame.
Flaked forms are prone to gradual oxidation. This material is not expected to
present a dust explosion hazard during normal transportation and storage
operations. However, a significant dust explosion can occur when an excessive
concentration of dust is dispersed in air and is subject to an ignition source
of sufficient energy. Minimize the potential for dust explosion by
eliminating/controlling ignition sources (bond and ground) and by using good
housekeeping practices during storage, transfer, and handling. Ensure
equipment is adequately grounded. Prevent dust from accumulating on overhead
horizontal surfaces and prevent dust from escaping from process equipment.
Use explosion relief vents on dust collectors and dust handling equipment.
Electrical equipment should conform to the National Electric Code. This
material is sensitive to electrostatic discharge ignition. Static electricity
can be generated when pouring this material into a receiving vessel. Prevent
electrostatic charge formation by bonding and grounding containers and
vessels. The plastic packaging film used to secure bags of material on
pallets can also develop static electricity-- remove packaging film in an
area free from ignitable vapors/dust. Refer to the latest edition of the
National Fire Protection Association (NFPA) 654 publication, "Standard for
the Prevention of Fire and Dust Explosions in the Chemical, Dye,
Pharmaceutical, and Plastics Industries", for complete discussion on dust
explosion prevention and control measures.
Store material at temperatures below 40C/104F.
Date Printed: 05-03-2005 Page: 5 of 7
Sartomer Company
Material Safety Data Sheet
Product: NORSOLENE W-100 Revised Date: 05-03-2005
MSDS ID: S-001363 Replaces Date: 01-17-2005
DECONTAMINATION PROCEDURES
Follow standard plant procedures or supervisor's instructions for
decontamination operations.
12. LABEL INFORMATION
USE STATEMENT
FOR INDUSTRIAL USE ONLY
SIGNAL WORD
CAUTION
PHYSICAL HAZARDS
POTENTIAL DUST EXPLOSION HAZARD
PRECAUTIONARY MEASURES
PREVENT ACCUMULATION OF DUST.
PREVENT ELECTROSTATIC CHARGE FORMATION.
AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
AVOID CONTACT WITH MOLTEN PRODUCT.
AVOID BREATHING DUST/VAPORS GENERATED FROM THERMAL PROCESSING.
USE WITH ADEQUATE VENTILATION/PERSONAL PROTECTION.
REMOVE SPILLED MATERIAL IMMEDIATELY FROM HARD, SMOOTH WALKING SURFACES.
WASH THOROUGHLY AFTER HANDLING.
KEEP CONTAINER CLOSED WHEN NOT IN USE.
BEFORE USING PRODUCT, READ MATERIAL SAFETY DATA SHEET (MSDS).
13. SUPPLEMENT
REGULATORY INFORMATION
TSCA Status
TSCA status: All components of this product are listed, or excluded from
listing, on the United States Environmental Protection Agency Toxic Substances
Control Act (TSCA) inventory.
California Proposition 65
California Proposition 65 Information: this product does not contain any
substances known to the state of California to cause cancer and/or
reproductive harm.
International Inventory Status
Canada (DSL) Included on inventory
Europe (EINECS) Polymer
Australia (AICS) Included on inventory
Japan (ENCS) not included on inventory
Korea (ECL) Included on inventory
Philippines (PICCS) Included on inventory
China Included on inventory
*Note - qualifiers and codes used in this MSDS
Date Printed: 05-03-2005 Page: 6 of 7
Sartomer Company
Material Safety Data Sheet
Product: NORSOLENE W-100 Revised Date: 05-03-2005
MSDS ID: S-001363 Replaces Date: 01-17-2005
EQ = Equal; AP = Approximately; LT = Less Than; GT = Greater Than;
TR = Trace; UK = Unknown; N/AP = Not Applicable; N/P = No Applicable
Information Found; N/DA = No Data Available
14. DISCLAIMERS
Some of the information presented and conclusions drawn herein are from
sources other than direct test data on the product itself. The information in
this MSDS was obtained from sources which we believe are reliable. However,
the information is provided without any warranty, express or implied,
regarding its correctness. The conditions or methods of handling, storage, use
and disposal of the product are beyond our control and may be beyond our
knowledge. For this and other reasons, we do not assume responsibility and
expressly disclaim liability for loss, damage or expense arising out of or in
any way connected with the handling, storage, use or disposal of the product.
This MSDS was prepared and is to be used only for this product. If the
product is used as a component in another product, this MSDS information may
not be applicable. This MSDS has been prepared in accordance with the
requirements of the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Date Printed: 05-03-2005 Page: 7 of 7
|