Sartomer Company, Inc.
MATERIAL SAFETY DATA SHEET
Product Name: Ricon P30D
MSDS ID #: P30D
Section I - GENERAL
Manufacturer:
Sartomer Company, Inc.
Oaklands Corporate Center
502 Thomas Jones Way
Exton, Pennsylvania 19341
Emergency Phone Numbers
1-800-424-9300 (CHEMTREC)
610-692-8401
Product Information
610-363-4100
Product Identification
Ricon庐 P30D
Trade Name:
CAS#: Mixture
CAS# Calcium Silicate: 1344-95-2
Chemical Name &
Synonyms: Polymer mixture with polybutadiene dispersed on synthetic calcium silicate
Chemical Family: Aliphatic hydrocarbon polymer mixture
Formula: Complex Polymeric
DOT Hazardous Materials Proper Shipping Name: Not Regulated
DOT Hazard Class: Not Regulated
SECTION II SUMMARY OF HAZARDS
HMIS: Health 1 Flammability 1 Reactivity 1 Other None
Physical Hazards: Slightly combustible solid
Inhalation OSHA PEL-15mg/m3 total nuisance; 5mg/m3 respirable dust
Acute Health Effects:
(short term) Skin may be slight skin irritant
Ingestion hazard may be slight ingestion hazard
Eye irritation eye irritation possible
Chronic Health Effects: No chronic hazards have been observed
(long term)
This product is NOT listed under: National Toxicology Program (NTP) Annual Report on Carcinogens
International Agency for Research on Cancer (IARC) Monographs
Regulatory Information:
TSCA: All ingredients of this product appear on the TSCA inventory.
SARA Title III-Section 313: This product does not contain a toxic chemical in excess of 1% of the mixture (.1% if a listed
carcinogen).
International Status
Page 1 of 4
Australia (AICS): included on inventory
Canada (DSL): included on inventory
China (CECS): included on inventory
Europe (EINECS): included on inventory
Japan (ENCS): included on inventory
Korea (ECL): included on inventory
Philippines (PICCS): included on inventory
SECTION III PHYSICAL AND CHEMICAL DATA
Boiling Point ( F): No defined boiling point decomposes above 475 by polymerization. Cracks into
(long term) gaseous and liquid products above 800 .
Vapor Pressure: Very low
Vapor Density: Not determined
Solubility in Water: Nil
Appearance and Odor: Grey to amber powder with some small lumps
Specific Gravity (H2O): > 1.0
% Volatile by Volume: < 3.0
Evaporation Rate: Very low
Freezing Point: Not determined
Conditions to Avoid: Oxidizing conditions, extreme temperatures
Materials to Avoid: Strong oxidizers, strong acids
SECTION IV FIRE AND EXPLOSION HAZARD DATA
Flash Point: > 250 F
Extinguishing Media: Foam or water spray, CO2, dry chemical, water
Special Fire Fighting
Procedures: Keep drums cool with water from hose.
Unusual Fire & Explosion
Hazards: Will tend to polymerize thermally at temperatures above 400 F (200 C). Once initiated, the
reaction generates sufficient heat to continue spontaneously. Heat from fire can generate
flammable vapors. Such fires are very smoky. Closed drums can rupture in a fire causing
flame to spread, increasing risk of burns. Personal contact with hot liquid after a fire can cause
severe burns due to high temperature. Notify authorities if liquid enters sewer or public waters.
SECTION V HEALTH HAZARDS
5mg/m3 respirable dust; 15mg/m3 total dust
Summary of Acute Hazards: OSHA PEL
ROUTE OF EXPOSURE SIGNS AND SYMPTOMS
Inhalation: Can cause drying of mucus membrane and irritation of the respiratory tract.
Eye Contact: May cause minor eye irritation, inflammation that is reversible.
Skin Contact: May produce skin irritation.
Ingestion: No significant signs or symptoms indicative of any adverse health hazards are expected to
occur as a result of ingestion.
Summary of Chronic
Hazards: Prolonged and repeated exposure to high concentrations in excess of the PEL, of product can cause
chronic pulmonary disease.
Special Health Effects: No additional medical information found.
SECTION VI REACTIVITY DATA
Page 2 of 4
Stability: Stable
Condition to Avoid: Keep away from excessive heat, avoid long exposure above 200 F.
Incompatibility: Incompatible with peroxides.
Hazardous Decomposition
Products: Small quantities of butadiene, along with other lower molecular weight hydrocarbons.
Hazardous Polymerization: May occur
SECTION VII PROECTIVE EQUIPMENT AND OTHER CONTROL MEASURES
Respiratory: Respirators to control dust.
Eye: Eye protection such as chemical splash goggles and/or face shield is recommended when
possibility exists for eye contact due to splashing or spraying liquid, airborne particles, or
vapor. Contact lenses should not be worn.
Skin: Depending on the conditions of use, gloves, apron, boots, head and face protection is
recommended. Equipment should be cleaned thoroughly after each use.
Engineering Controls: Ventilation, mechanical or natural, is recommended to maintain dust levels below PEL.
Other Hygienic and
Work Practices: Use good personal hygiene practices. Wash hands before eating, drinking, smoking, or
using toilet facilities. Promptly remove soiled clothing/wash thoroughly before reuse.
Shower after work using plenty of soap and water. No special work practices are needed
beyond the above-recommended actions under anticipated condition of normal use.
SECTION VIII OCCUPATIONAL EXPOSURE LIMITS
No established standards
SECTION IX EMERGENCY AND FIRST AID
Inhalation: Remove to fresh air, drink water to clear throat and blow nose to evacuate dust.
Eye Contact: In case of eye contact, immediately rinse with clean water for 20-30 minutes. Retract eyelids
often. Obtain emergency medical attention if pain, blinking, tears or redness persists.
Skin Contact: Remove contaminated clothing as needed. Wash skin thoroughly with mild soap/water.
Flush with lukewarm water for 15 minutes. Wipe off resin with dry or oily rag. Baby oil will
remove stickiness, as will waterless cleaner.
Ingestion: Not expected to present a significant ingestion hazard under anticipated conditions of
normal use.
Emergency Medical
Treatment Procedures: After adequate first aid, no further treatment is required unless symptoms reappear. Treat
symptomatically.
SECTION X SPILL AND DISPOSAL
Precautions if Material is
Spilled or Released: Clean up by sweeping. Use suitable disposal containers. On water, material may float or
sink, may biodegrade. Contain/minimize dispersion/collect. Disperse residue to reduce
aquatic harm. Report per Reg. Requirements.
Page 3 of 4
Waste Disposal Methods: Follow all applicable Federal, state and local regulations when disposing waste. May
biodegrade. Avoid overloading/poisoning plant biomass. Assure effluent complies with
applicable regulations. Contaminated product, soil or water may be designated RCRA
Hazardous Waste.
SECTION XI COMPONENTS
(This may not be a complete list of components.)
CAS # COMPOSITION AMT #
Proprietary mixture: NA 65 - 75%
Synthetic Calcium Silicate 1344-95-2 25 35%
SECTION XII ADDITIONAL PRECAUTIONS
Handling, Storage & Decon-
tamination Procedures: Store away from heat, sparks, open flames and strong oxidizing agents. Avoid overheating
which may adversely affect quality or overpressure container(s).
Follow standard plant decontamination operations.
General Comments: Some of the information presented and conclusions drawn herein are from sources other
than direct test data on the product itself. Avoid long storage above 90掳F.
DISCLAIMER OF LIABILITY
The information in this MSDS was obtained from sources, which we believe are reliable. HOWEVER, THE INFORMATION
IS PROVIDED WITHOUT ANY WARRANTY, EXPRESSED OR IMPLIED, REGARDING ITS CORRECTNESS.
The conditions or methods of handling, storage, use and disposal of the product are beyond our control and may be beyond
our knowledge. FOR THIS AND OTHER REASONS, WE DO NOT ASSUME RESPONSIBILITY AND EXPRESSLY
DISCLAIM LIABILITY FOR LOSS, DAMAGE OR EXPENSE ARISING OUT OF, OR IN ANY WAY CONNECTED WITH THE
HANDLING, STORAGE, USE OR DISPOSAL OF THE PRODUCT.
Create Date: 2000-12-10 16:43:31
Revision Date: 2005-01-18 10:21:22
Page 4 of 4
|