Sartomer Company, Inc.
MATERIAL SAFETY DATA SHEET
Product Name: Ricon 131MA17
MSDS ID #: 131MA17
Section I - GENERAL
Manufacturer:
Sartomer Company, Inc.
Oaklands Corporate Center
502 Thomas Jones Way
Exton, Pennsylvania 19341
Emergency Phone Numbers
1-800-424-9300 (CHEMTREC)
610-692-8401
Product Information
610-363-4100
Product Identification
Ricon庐 131MA17
Trade Name:
CAS#: 25655-35-0
Chemical Name &
Synonyms: Polybutadiene adducted with maleic anhydride
Chemical Family: Aliphatic Polyanhydride
Formula: Complex Polymeric
DOT Hazardous Materials Proper Shipping Name: Not Regulated
DOT Hazard Class: Not Regulated
SECTION II SUMMARY OF HAZARDS
HMIS: Health 1 Flammability 1 Reactivity 1 Other None
Physical Hazards: Slightly combustible liquid
Acute Health Effects: Inhalation respiratory irritant
(short term) Skin may be slight skin irritant
Ingestion hazard may be slight ingestion hazard
Eye irritation no data, mild eye irritation possible
Chronic Health Effects: No chronic hazards have been observed
Page 1 of 5
(long term)
This product is NOT listed under: National Toxicology Program (NTP) Annual Report on
Carcinogens International Agency for Research on Cancer (IARC) Monographs
Regulatory Information:
TSCA: All ingredients of this product appear on the TSCA inventory.
SARA Title III-Section 313: This product does not contain a toxic chemical in excess of 1% of the
mixture (0.1% if a listed carcinogen).
International Status
Australia (AICS): included on inventory
Canada (DSL): included on inventory
China (CECS): included on inventory
Europe (EINECS): not included on inventory
Japan (ENCS): included on inventory
Korea (ECL): included on inventory
Philippines (PICCS): included on inventory
SECTION III PHYSICAL AND CHEMICAL DATA
Boiling Point ( F): No defined boiling point decomposes above 475 by polymerization.
(long term) Cracks into gaseous and liquid products above 800 .
Vapor Pressure: Very low
Vapor Density: Not determined
Solubility in Water: Nil
Appearance and Odor: Viscous, brown to amber liquid, mild hydrocarbon odor.
Specific Gravity (H2O): < 1.0
% Volatile by Volume: < 1.0
Evaporation Rate: Very low
Freezing Point: Not determined
Conditions to Avoid: Oxidizing conditions, extreme temperatures
Materials to Avoid: Strong oxidizers, strong acids
SECTION IV FIRE AND EXPLOSION HAZARD DATA
Flash Point: > 250 F
Extinguishing Media: Foam or water spray, CO2, dry chemical, water
Special Fire Fighting
Procedures: Keep drums cool with water from hose.
Unusual Fire & Explosion
Hazards: Will tend to polymerize thermally at temperatures above 400 F
(200 C). Once initiated, the reaction generates sufficient heat to
continue spontaneously. Heat from fire can generate flammable
vapors. Such fires are very smoky. Closed drums can rupture in
a fire causing flame to spread, increasing risk of burns.
Personal contact with hot liquid after a fire can cause severe
burns due to high temperature. Notify authorities if liquid enters
sewer or public waters.
Page 2 of 5
SECTION V HEALTH HAZARDS
Summary of Acute Hazards: Slight health hazards see below for route-specific details.
ROUTE OF EXPOSURE SIGNS AND SYMPTOMS
Inhalation: No appropriate human or animal health effects data is known to
exist.
Eye Contact: May cause minor eye irritation.
Skin Contact: May produce skin irritation.
Ingestion: No significant signs or symptoms indicative of any adverse
health hazards are expected to occur as a result of ingestion.
Summary of Chronic
Hazards: No chronic health hazards have been found to be associated with this
material.
Special Health Effects: No additional medical information found.
SECTION VI REACTIVITY DATA
Stability: Stable
Condition to Avoid: Keep away from excessive heat, avoid long exposure above
190 F.
Incompatibility: Incompatible with peroxides and many reactive materials.
Hazardous Decomposition
Products: Small quantities of butadiene and maleic anhydride, along
with other lower molecular weight hydrocarbons.
Hazardous Polymerization: May occur
SECTION VII PROECTIVE EQUIPMENT AND OTHER
CONTROL MEASURES
Respiratory: No special respiratory protection equipment is recommended
under anticipated conditions of normal use with adequate
ventilation.
Eye: Eye protection such as chemical splash goggles and/or face
shield is recommended when possibility exists for eye contact
due to splashing or spraying liquid, airborne particles, or
vapor. Contact lenses should not be worn.
Skin: Depending on the conditions of use, gloves, apron, boots,
head and face protection is recommended. Equipment
should be cleaned thoroughly after each use.
Page 3 of 5
Engineering Controls: No special ventilation is recommended under anticipated
conditions of normal use beyond that needed for normal
comfort control.
Other Hygienic and
Work Practices: Use good personal hygiene practices. Wash hands before
eating, drinking, smoking, or using toilet facilities. Promptly
remove soiled clothing/wash thoroughly before reuse.
Shower after work using plenty of soap and water. No special
work practices are needed beyond the above recommended
actions under anticipated condition of normal use.
SECTION VIII OCCUPATIONAL EXPOSURE LIMITS
No established standards
SECTION IX EMERGENCY AND FIRST AID
Inhalation: Not expected to present a significant inhalation hazard under
anticipated conditions of normal use.
Eye Contact: In case of eye contact, immediately rinse with clean water for
20-30 minutes. Retract eyelids often. Obtain emergency
medical attention if pain, blinking, tears or redness persists.
Skin Contact: Remove contaminated clothing as needed. Wash skin
thoroughly with mild soap/water. Flush with lukewarm water
for 15 minutes. Wipe off resin with dry or oily rag. Baby oil
will remove stickiness, as will waterless cleaner.
Ingestion: Not expected to present a significant ingestion hazard under
anticipated conditions of
normal use.
Emergency Medical
Treatment Procedures: After adequate first aid, no further treatment is required
unless symptoms reappear. Treat symptomatically.
SECTION X SPILL AND DISPOSAL
Precautions if Material is
Spilled or Released: Stop release. Prevent flow to sewers/public waters. Restrict
water use for cleanup. Slippery walking/spread granular
cover. Impound/recover large land spill. Soak up small spill
with inert solids. Use suitable disposal containers. On water,
material may float or sink, may biodegrade. Contain/minimize
dispersion/collect. Disperse residue to reduce aquatic harm.
Report per Reg. Requirements.
Page 4 of 5
Waste Disposal Methods: Use registered transporters. May be incinerated for energy
recovery. Follow all local, state and Federal regulations when
disposing.
SECTION XI COMPONENTS
(This may not be a complete list of components.)
CAS # COMPOSITION AMT #
Polybutadiene adducted
with maleic anhydride: 25655-35-0 100%
SECTION XII ADDITIONAL PRECAUTIONS
Handling, Storage & Decon-
tamination Procedures: Liquid material is slippery remove small leaks/spills from
walking surface with solid absorbents. Use caution to avoid
falls causing serious injury. Store away from heat, sparks,
open flames and strong oxidizing agents. Avoid overheating
which may adversely affect quality or overpressure
container(s). Follow standard plant decontamination
operations.
General Comments: Some of the information presented and conclusions drawn
herein are from sources other than direct test data on the
product itself. Do not use electrical drum heaters without
reliable upper temperature control. If heated too hot (above
400 F), a run away polymerization may occur. Steam drum
heaters are recommended.
DISCLAIMER OF LIABILITY
The information in this MSDS was obtained from sources which we believe are reliable.
HOWEVER, THE INFORMATION IS PROVIDED WITHOUT ANY WARRANTY, EXPRESSED
OR IMPLIED, REGARDING ITS CORRECTNESS.
The conditions or methods of handling, storage, use and disposal of the product are beyond our
control and may be beyond our knowledge. FOR THIS AND OTHER REASONS, WE DO NOT
ASSUME RESPONSIBILITY AND EXPRESSLY DISCLAIM LIABILITY FOR LOSS, DAMAGE OR
EXPENSE ARISING OUT OF, OR IN ANY WAY CONNECTED WITH THE HANDLING,
STORAGE, USE OR DISPOSAL OF THE PRODUCT.
Create Date: 2001-05-08 12:16:04
RevisionDate: 2005-01-18 09:53:35
Page 5 of 5
|