3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
Material Safety Data Sheet
Copyright, 2006, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 05/12/2006
Supercedes Date: 12/05/2005
Document Group: 18-5798-6
Product Use:
Specific Use: structural adhesive
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Epoxy Resin 25068-38-6 30 - 60
Aluminum Pigments 7429-90-5 15 - 40
Synthetic Elastomer- N.J.T.S. Reg No. 04499600-5706P Trade Secret 1- 5
Epoxy Resin 41638-13-5 1- 5
Amorphous Silica 67762-90-7 1- 5
Dicyandiamide 461-58-5 1- 5
p-Chlorophenyl-Dimethylurea 150-68-5 1- 5
1,4-bis[(2,3-Epoxypropoxy)Methyl]Cyclohexane 14228-73-0 0.1 - 1
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Specific Physical Form: Paste
Odor, Color, Grade: gray
General Physical Form: Solid
Immediate health, physical, and environmental hazards: Hazardous polymerization may occur. May cause allergic skin
reaction.
_________________________________________________________________________________________________
Page 1 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Vapors released during curing may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or
hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Prolonged or repeated exposure may cause:
Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.
Inhalation:
Vapors released during curing may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal
discharge, headache, hoarseness, and nose and throat pain.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: If signs/symptoms develop, remove person to fresh air. If signs/symptoms persist, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
No Data Available
Autoignition temperature
480 潞F [Test Method: Closed Cup]
Flash Point
_________________________________________________________________________________________________
Page 2 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
No Data Available
Flammable Limits - LEL
No Data Available
Flammable Limits - UEL
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may be used to blanket the fire. Wear full protective equipment (Bunker Gear) and a
self-contained breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: No unusual fire or explosion hazards are anticipated.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more
information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be
cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical
ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition
source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains
and build dikes to prevent entry into sewer systems or bodies of water. Working from around the edges of the spill inward, cover with
bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry.
Collect as much of the spilled material as possible. Clean up residue with an appropriate solvent selected by a qualified and
authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and MSDS. Collect the
resulting residue containing solution. Place in a closed container approved for transportation by appropriate authorities. Dispose of
collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
For industrial or professional use only. Keep out of the reach of children. Avoid eye contact with vapors, mists, or spray. Avoid
breathing of vapors, mists or spray. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap
and water. Avoid breathing of vapors created during cure cycle. Avoid contact with oxidizing agents. Keep container closed when
not in use.
7.2 STORAGE
Store away from heat. Store out of direct sunlight. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use in a well-ventilated area. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below
Occupational Exposure Limits and/or control mist, vapor, or spray. If ventilation is not adequate, use respiratory protection
_________________________________________________________________________________________________
Page 3 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
equipment. Use with appropriate local exhaust ventilation. Provide appropriate local exhaust when product is heated. Provide
appropriate local exhaust for cutting, grinding, sanding or machining.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Polyvinyl Alcohol (PVA), Polyethylene/Ethylene Vinyl Alcohol.
8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half mask R95 particulate respirator, Half mask or full facepiece air-purifying respirator with N100 particulate
filters, Half facepiece or fullface air-purifying respirator with P100 particulate filters, Half facepiece or fullface air-purifying
respirator with P95 particulate filters, Half facepiece or fullface air-purifying respirator with N95 particulate filters. Consult the
current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not ingest. Wash hands after handling and before eating. Do not eat, drink or smoke when using this product. Wash exposed areas
thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
Aluminum Pigments ACGIH TWA 10 mg/m3
Aluminum Pigments OSHA TWA, respirable 5 mg/m3 Table Z-1
Aluminum Pigments OSHA TWA, as total dust 15 mg/m3 Table Z-1
ALUMINUM PYRO POWDERS ACGIH TWA, as Al 5 mg/m3
ALUMINUM PYRO POWDERS OSHA TWA, as Al 5 mg/m3 Table Z-1A
Amorphous Silica CMRG CEIL 5 mg/m3
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Paste
Specific Physical Form:
gray
Odor, Color, Grade:
Solid
General Physical Form:
No Data Available
Autoignition temperature
480 潞F [Test Method: Closed Cup]
Flash Point
No Data Available
Flammable Limits - LEL
No Data Available
Flammable Limits - UEL
_________________________________________________________________________________________________
Page 4 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
>=260 潞C
Boiling point
1.44 g/ml
Density
No Data Available
Vapor Density
No Data Available
Vapor Pressure
1.44 [Ref Std: WATER=1]
Specific Gravity
Not Applicable
pH
Not Applicable
Melting point
Nil
Solubility in Water
Not Applicable
Evaporation rate
Negligible
Evaporation rate
0%
Volatile Organic Compounds
0 % weight
Percent volatile
0%
VOC Less H2O & Exempt Solvents
>= 1000000 centipoise [@ 73.4 潞F]
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Strong oxidizing agents; Heat; Sparks and/or flames; Avoid curing large quantities of material
to prevent a premature reaction (exotherm) with production of intense heat and smoke.
Hazardous Polymerization: Hazardous polymerization may occur.
Hazardous Decomposition or By-Products
Substance Condition
Aldehydes During Combustion
Chlorine During Combustion
Carbon monoxide During Combustion
Carbon dioxide During Combustion
Hydrogen Chloride During Combustion
Hydrogen Cyanide During Combustion
Ammonia During Combustion
Oxides of Nitrogen During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
_________________________________________________________________________________________________
Page 5 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Dispose of completely cured (or polymerized) wastes in a sanitary landfill.
As a disposal alternative, incinerate uncured product in an industrial or commercial incinerator in the presence of a combustible
material.
Combustion products will include HCl. Facility must be capable of handling halogenated materials.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
62-2214-2930-1, 62-2214-2932-7, 62-2214-2935-0, 62-2214-6530-5, 62-2214-7530-4, 62-2214-8530-3
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No Reactivity Hazard - Yes Immediate Hazard - Yes Delayed Hazard - No
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No % by Wt
Aluminum Pigments 7429-90-5 15 - 40
p-Chlorophenyl-Dimethylurea 150-68-5 1- 5
STATE REGULATIONS
Contact 3M for more information.
_________________________________________________________________________________________________
Page 6 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All the components of this product are listed on China's Inventory of Chemical Substances.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
This material contains one or more ingredients that may be regulated by the International Traffic in Arms Regulation (ITAR), an
export control of US military technology and chemicals. Prior to export of this material or any product containing this material,
determine whether a proper license from the Department of State must be obtained. See 22CFR 120-130 for any specific requirements.
Contact 3M for more information.
WHMIS: Hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 0 Reactivity: 1 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Revision Changes:
Copyright was modified.
Section 13: Waste disposal method information was modified.
Section 1: Initial issue message was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
_________________________________________________________________________________________________
Page 7 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) 2214 Regular Epoxy Adhesive 05/12/2006
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8
|