3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
Material Safety Data Sheet
Copyright, 2005, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 06/09/2005
Supercedes Date: 05/24/2001
Document Group: 10-2971-9
Product Use:
Intended Use: solvent based plastic adhesive
Specific Use: Plastic Adhesive
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
ACETONE 67-64-1 65 - 75
ACRYLIC POLYMER Trade Secret 20 - 30
TETRAHYDROFURAN 109-99-9 3- 7
GLYCEROL ESTERS OF ROSIN ACIDS 8050-31-5 1- 5
NITRILE RUBBER 9010-81-5 0.5 - 1.5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Clear liquid - ketone odor
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and
explode. Extremely flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and
flash back. May cause severe eye irritation. May cause target organ effects.
3.2 POTENTIAL HEALTH EFFECTS
_________________________________________________________________________________________________
Page 1 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
Eye Contact:
Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing, cloudy appearance of the cornea, and
impaired vision.
Skin Contact:
Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching.
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
No Data Available
Autoignition temperature
0 潞F
Flash Point
2.6 %
Flammable Limits - LEL
12.8 %
Flammable Limits - UEL
_________________________________________________________________________________________________
Page 2 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Extremely
flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards,
respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information
on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up
by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-
sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to
disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build
dikes to prevent entry into sewer systems or bodies of water. Cover spill area with a fire-extinguishing foam designed for use on
solvents, such as alcohols and acetone, that can dissolve in water. An AR - AFFF type foam is recommended. Working from around
the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in
sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a toxic, corrosivity or
flammability hazard. Collect as much of the spilled material as possible using non-sparking tools. Clean up residue with water.
Collect the resulting residue containing solution. Place in a metal container approved for transportation by appropriate authorities.
Seal the container. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Keep away from heat, sparks, open flame, pilot lights and other sources of ignition. Vapors may ignite explosively. May cause flash
fire. Prevent build-up of vapors - open all windows and doors. Maintain vapor concentrations below recommended exposure limits.
Use only with cross-ventilation. Without adequate ventilation, vapors may settle in low-lying areas. Keep away from heat, sparks, and
open flame. Do not smoke or ignite matches, lighters, etc. Avoid static discharge. No smoking while handling this material. Ground
containers securely when transferring contents. Wear low static or properly grounded shoes. Contents may be under pressure, open
carefully. Avoid breathing of vapors, mists or spray. Do not eat, drink or smoke when using this product. Wash exposed areas
thoroughly with soap and water. Avoid eye contact with vapors, mists, or spray. Avoid contact with oxidizing agents. Keep out of
the reach of children.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container
_________________________________________________________________________________________________
Page 3 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
tightly closed. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide appropriate local exhaust ventilation on open containers.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Polyethylene/Ethylene Vinyl Alcohol.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece air-purifying respirator with organic vapor/acid gas cartridges and P100 particulate prefilters.
Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Not applicable.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
ACETONE ACGIH TWA 500 ppm Table A4
ACETONE ACGIH STEL 750 ppm Table A4
ACETONE OSHA TWA, Vacated 750 ppm
ACETONE OSHA TWA 1000 ppm Table Z-1
ACETONE OSHA STEL, Vacated 1000 ppm
TETRAHYDROFURAN ACGIH TWA 200 ppm
TETRAHYDROFURAN ACGIH STEL 250 ppm
TETRAHYDROFURAN CMRG TWA 25 ppm
TETRAHYDROFURAN CMRG STEL 75 ppm
TETRAHYDROFURAN OSHA TWA 200 ppm Table Z-1A
TETRAHYDROFURAN OSHA STEL 250 ppm Table Z-1A
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
_________________________________________________________________________________________________
Page 4 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
Clear liquid - ketone odor
Odor, Color, Grade:
Liquid
General Physical Form:
No Data Available
Autoignition temperature
0 潞F
Flash Point
2.6 %
Flammable Limits - LEL
12.8 %
Flammable Limits - UEL
132 潞F [Details: CONDITIONS: (acetone)]
Boiling point
2 [Ref Std: AIR=1]
Vapor Density
180 mmHg [Details: CONDITIONS: @ 68F]
Vapor Pressure
0.89 [Ref Std: WATER=1]
Specific Gravity
No Data Available
pH
No Data Available
Melting point
Slight (less than 10%)
Solubility in Water
1.9 [Ref Std: ETHER=1]
Evaporation rate
0 % weight
Hazardous Air Pollutants
Approximately 39 g/l [Test Method: calculated SCAQMD rule
Volatile Organic Compounds
443.1]
Approximately 76 % weight
Percent volatile
Approximately 196 g/l [Test Method: calculated SCAQMD rule
VOC Less H2O & Exempt Solvents
443.1]
375 - 675 centipoise
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Strong oxidizing agents
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Aldehydes During Combustion
Hydrocarbons During Combustion
Carbon monoxide During Combustion
Carbon dioxide During Combustion
Hydrogen Cyanide During Combustion
Ketones During Combustion
Oxides of Nitrogen During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
_________________________________________________________________________________________________
Page 5 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Reclaim solvent if feasible. Incinerate in a permitted hazardous waste incinerator. As a disposal
alternative, dispose of waste product in a permitted hazardous waste facility.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
62-2262-3330-2, 62-2262-5530-5, 62-2262-6530-4, 62-2262-6535-3, 62-2262-7530-3, 62-2262-8530-2, 62-2262-9530-1
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - No
This material contains a chemical which requires export notification under TSCA Section 12[b]:
Ingredient (Category if applicable) C.A.S. No Regulation Status
TETRAHYDROFURAN 109-99-9 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
ACETONE 67-64-1 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
_________________________________________________________________________________________________
Page 6 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 3 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
No revision information is available.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
_________________________________________________________________________________________________
Page 7 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Plastic Adhesive 2262 06/09/2005
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8
|