MATERIAL SAFETY DATA SHEET
Sikacem 103
HMIS
HEALTH *2
FLAMMABILITY 0
REACTIVITY 0
E
PERSONAL PROTECTION
1. Product And Company Identification
Supplier Manufacturer
Sika Corporation Sika Corporation
201 Polito Ave 201 Polito Ave
Lyndhurst, NJ 07071 Lyndhurst, NJ 07071
Company Contact: EHS Department Company Contact: EHS Department
Telephone Number: 201-933-8800 Telephone Number: 201-933-8800
FAX Number: 201-933-9379 FAX Number: 201-933-9379
Web Site: www.sikausa.com Web Site: www.sikausa.com
Supplier Emergency Contacts & Phone Number Manufacturer Emergency Contacts & Phone Number
CHEMTREC: 800-424-9300 CHEMTREC: 800-424-9300
INTERNATIONAL: 703-527-3887 INTERNATIONAL: 703-527-3887
Issue Date: 06/27/2006
Product Name: Sikacem 103
CAS Number: Not Established
Chemical Family: Cementitious Mortar
MSDS Number: 3932
Product Code: 0158540
2. Composition/Information On Ingredients
Ingredient CAS Percent Of
Name Number Total Weight
CEMENT, PORTLAND 65997-15-1
SILICA, AMORPHOUS 7631-86-9
SILICA, QUARTZ 14808-60-7
3. Hazards Identification
Eye Hazards
May cause eye irritation.
Skin Hazards
Product becomes alkaline when exposed to moisture. May cause a reversible inflammatory effect on skin or
tissue at the site of contact.
Ingestion Hazards
May be harmful if swallowed.
Page 1 of 5
MATERIAL SAFETY DATA SHEET
Sikacem 103
3. Hazards Identification - Continued
Inhalation Hazards
Breathing dust may cause nose, throat or lung irritation. Respirable crystalline silica can cause silicosis, a fibrosis
(scarring) of the lungs. Silicosis may be progressive.
4. First Aid Measures
Eye
In case of contact, hold eyelids apart and immediately flush eyes with plenty of tepid water for at least 15 minutes.
Get medical attention immediately if irritation develops and persists.
Skin
In case of contact, immediately flush skin with soap and plenty of tepid water for at least 15 minutes. Get medical
attention immediately if irritation (redness, rash, blistering) develops and persists.
Ingestion
If swallowed, do not induce vomiting unless directed to do so by medical personnel.
Inhalation
Remove to fresh air. If not breathing, give artificial respiration, seek medical attention.
5. Fire Fighting Measures
Flash Point: >200 掳F
Fire And Explosion Hazards
None known
Extinguishing Media
In case of fire, use water spray (fog) foam, dry chemical, or CO2.
Fire Fighting Instructions
In the event of a fire, firefighters should wear full protective clothing and NIOSH-approved self-contained
breathing apparatus with a full facepiece operated in the pressure demand or other positive pressure mode.
6. Accidental Release Measures
Avoid release to the environment. Using appropriate personal protective equipment (PPE), shovel material into waste
containers taking care to minimize dust. Dampen if necessary to control dust. Vacuum clean dust with equipment fitted
with High Efficiency Particulate Air (HEPA) filters.
7. Handling And Storage
Handling And Storage Precautions
Keep out of reach of children. Store in a cool, dry, well ventilated area. Keep containers tightly closed.
Work/Hygienic Practices
Wash thoroughly with soap and water after handling.
8. Exposure Controls/Personal Protection
Engineering Controls
Use of a system of local and/or general exhaust is recommended to keep employee below applicable exposure
limits. Refer to the current edition of "Industrial Ventilation: A Manual of Recommended Practice" published by
the American Conference of Governmental Industrial Hygienists for information on the design, installation, use,
and maintenance of exhaust systems.
Eye/Face Protection
Safety glasses with side shields or goggles.
Page 2 of 5
MATERIAL SAFETY DATA SHEET
Sikacem 103
8. Exposure Controls/Personal Protection - Continued
Skin Protection
Chemical-resistant gloves. Lab coat or other work clothing to prevent skin exposure (Long sleeve shirt and long
pants). Launder before reuse.
Respiratory Protection
A respirator protection program that meets 29 CFR 1910.134 requirement must be followed whenever workplace
conditions warrant a respirator's use. In areas where the Permissible Exposure Limits are exceeded, use a
properly fitted NIOSH-approved respirator.
Ingredient(s) - Exposure Limits
CEMENT, PORTLAND
ACGIH TLV-TWA - 10 mg/m3
OSHA PEL -TWA - 15 mg/m3 (total dust)
OSHA PEL - TWA - 5 mg/m3 (respirable dust)
SILICA, AMORPHOUS
ACGIH TLV-TWA 10 mg/m3
OSHA PEL-TWA 20 mppcf
OSHA PEL-TWA 80 / %SiO2 mg/m3
SILICA, QUARTZ
ACGIH TLV-TWA 0.05 mg/m3 (Notice of Intended Change)
ACGIH TLV-TWA 0.025 mg/m3 (Proposed)
OSHA PEL-TWA 30/%SiO2+2 mg/m3
OSHA PEL-TWA 10/%SiO2+2 mg/m3
OSHA PEL-TWA 250/%SiO+5 mppcf
9. Physical And Chemical Properties
Appearance
Gray mortar
Odor
No odor
Chemical Type: Mixture
Physical State: Solid
10. Stability And Reactivity
Stability: STABLE
Hazardous Polymerization: WILL NOT OCCUR
Conditions To Avoid (Stability)
Contact of silica with powerful oxidizing agents such as fluorine, chlorine, trifluoride, manganese trioxide, oxygen
difluoride, may cause fires. Upon direct contact with water, material will harden.
Incompatible Materials
None Known
Hazardous Decomposition Products
Silica will dissolve in hydrofluoric acid and produce a corrosive gas - silicon tetrafluoride.
Conditions To Avoid (Polymerization)
None known
Page 3 of 5
MATERIAL SAFETY DATA SHEET
Sikacem 103
11. Toxicological Information
Ingredient(s) - Carginogenicity
SILICA, AMORPHOUS
Listed In The IARC Monographs
SILICA, QUARTZ
NTP - Listed On The National Toxicology Program
Listed In The IARC Monographs
12. Ecological Information
No Data Available...
13. Disposal Considerations
Dispose in accordance with applicable federal, state and local government regulations. Waste generators must
determine whether a discarded material is classified as a hazardous waste. USEPA guidelines for the classification
determination are listed in 40 CFR Parts 261.3. Additionally, waste generators must consult state and local hazardous
waste regulations to ensure complete and accurate classification.
14. Transport Information
Proper Shipping Name
Not Regulated by the US DOT
15. Regulatory Information
U.S. Regulatory Information
All ingredients of this product are listed or are excluded from listing under the U.S. Toxic Substances Control Act
(TSCA) Chemical Substance Inventory.
SARA Hazard Classes
Acute Health Hazard
Chronic Health Hazard
SARA Section 313 Notification
This product does not contain any ingredients regulated under Section 313 of the Emergency Planning and
Community Right-To-Know Act of 1986 or 40 CFR 372.
State Regulations
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or
other reproductive harm.
Ingredient(s) - State Regulations
SILICA, AMORPHOUS
New Jersey - Workplace Hazard
Pennsylvania - Workplace Hazard
Massachusetts - Hazardous Substance
SILICA, QUARTZ
New Jersey - Workplace Hazard
Pennsylvania - Workplace Hazard
California - Proposition 65
Massachusetts - Hazardous Substance
16. Other Information
No Data Available...
Page 4 of 5
MATERIAL SAFETY DATA SHEET
Sikacem 103
16. Other Information - Continued
HMIS Rating
Health: *2
F i re : 0
Reactivity: 0
PP E: E
Revision/Preparer Information
MSDS Preparer: EHS Deprtmant
MSDS Preparer Phone Number: 201 933 8800
This MSDS Supercedes A Previous MSDS Dated: 06/27/2006
Disclaimer
The information contained in this Material Safety Data Sheet applies only to the actual Sika Corporation ("Sika")
product identified and described herein. This information is not intended to address, nor does it address the use
or application of the identified Sika product in combination with any other material, product or process. All of the
information set forth herein is based on technical data regarding the identified product that Sika believes to be
reliable as of the date hereof. Prior to each use of any Sika product, the user must always read and follow the
warnings and instructions on the product's current Technical Data Sheet, product label and Material Safety Data
Sheet for each Sika product, which are available at web site and/or telephone number listed in Section 1 of this
MSDS.
SIKA MAKES NO WARRANTIES EXPRESS OR IMPLIED AND ASSUMES NO LIABILITY ARISING FROM THIS
INFORMATION OR ITS USE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL THEORY FOR SPECIAL OR
CONSEQUENTIAL DAMAGES AND SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS PRODUCT IN A
MANNER TO INFRINGE ON ANY PATENT OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD BY
OTHERS.
All sales of Sika products are subject to its current terms and conditions of sale available at www.sikacorp.com or
201-933-8800.
SIKA CORPORATION
Printed Using MSDS Generator鈩? 2000
Page 5 of 5
|