MATERIAL SAFETY DATA SHEET
Page 1 of 4
Sikament N
HMIS
HEALTH 1
FLAMMABILITY 0
REACTIVITY 0
B
PERSONAL PROTECTION
1. Product And Company Identification
Supplier Manufacturer
Sika Corporation Sika Corporation
201 Polito Ave 201 Polito Ave
Lyndhurst, NJ 07071 Lyndhurst, NJ 07071
Company Contact: EHS Department Company Contact: EHS Department
Telephone Number: 201-933-8800 Telephone Number: 201-933-8800
FAX Number: 201-933-9379 FAX Number: 201-933-9379
Web Site: www.sikausa.com Web Site: www.sikausa.com
Supplier Emergency Contacts & Phone Number Manufacturer Emergency Contacts & Phone Number
CHEMTREC: 800-424-9300 CHEMTREC: 800-424-9300
INTERNATIONAL: 703-527-3887 INTERNATIONAL: 703-527-3887
Issue Date: 09/12/2003
Product Name: Sikament N
CAS Number: Not Established
Chemical Family: Sodium Naphthalene Sulphonate Condensate Solution
Chemical Formula: RMF-
MSDS Number: 2860
Product Code: P172540
2. Composition/Information On Ingredients
Ingredient CAS Percent Of
Name Number Total Weight
SODIUM SALT OF POLY-NAPHTHALENE SULFONIC ACID 36290-04-7
3. Hazards Identification
Eye Hazards
May cause eye irritation.
Skin Hazards
Prolonged or repeated skin contact with liquid may cause skin irritantion.
Ingestion Hazards
May be harmful if swallowed.
Inhalation Hazards
None expected under normal conditions of use. Overexposure to mist or spray may cause irritation of respiratory
tract.
MATERIAL SAFETY DATA SHEET Page 2 of 4
Sikament N
4. First Aid Measures
Eye
In case of contact, hold eyelids apart and immediately flush eyes with plenty of trpid water for at least 15 minutes.
Get medical attention immediately if irritation develops and persists.
Skin
In case of contact, immediately flush skin with soap and plenty of trepid water for at least 15 minutes. Get medical
attention immediately if irritation (redness, rash, blistering) develops and persists.
Ingestion
If victim is fully conscious, give one or two cups of water or milk to drink. Get medical attention. If swallowed, do
not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an
unconscious victim.
Inhalation
Remove to fresh air. Treat any irriatation symptomatically. Get medical attention if irritation persists.
5. Fire Fighting Measures
Fire And Explosion Hazards
This product is an aqueous, non-flammable solution and will not support combustion.
Extinguishing Media
Use the appropriate extinguishing media for the surrounding fire.
Fire Fighting Instructions
In the event of a fire, firefighters should wear full protective clothing and NIOSH-approved self-contained breathing
apparatus with a full facepiece operated in the pressure demand or other positive pressure mode.
6. Accidental Release Measures
Avoid release to the environment. Use appropriate Personal Protective Equipment (PPE). Contain spill and collect with
absorbent material and transfer into suitable containers. Do not flush to sewer or allow to enter waterways. Ventilate
enclosed area.
7. Handling And Storage
Handling And Storage Precautions
Keep out of reach of children. Not for internal consumption.
Handling Precautions
Allow to warm to room temperature and mix well before using.
Storage Precautions
Store in a cool dry area. Keep containers tightly closed. Keep from freezing.
Work/Hygienic Practices
Wash thoroughly with soap and water after handling.
8. Exposure Controls/Personal Protection
Engineering Controls
Use with adequate general and local exhaust ventilation. Refer to the current edition of "Industrial Ventilation: A
Manual of Recommended Practice" published by the American Conference of Governmental Industrial Hygienists
for information on the design, installation, use, and maintenance of exhaust systems.
Eye/Face Protection
Faceshield over safety glasses or goggles.
Skin Protection
Chemical-resistant gloves. Lab coat or other work clothing to prevent skin exposure (Long sleeve shirt and long
pants). Launder before reuse.
MATERIAL SAFETY DATA SHEET Page 3 of 4
Sikament N
8. Exposure Controls/Personal Protection - Continued
Respiratory Protection
None normally required. A respirator protection program that meets 29 CFR 1910.134 requirement must be
followed whenever workplace conditions warrant a respirator's use.
9. Physical And Chemical Properties
Appearance
Dark Amber Liquid
Odor
Bland Odor
Chemical Type: Mixture
Physical State: Liquid
Melting Point: Not Applicable 掳F
Boiling Point: Not Available 掳F
Specific Gravity: 1.22
Percent Volatiles: 59% (all water)
Packing Density: 10 pounds / gallon
Vapor Pressure: Not Available
Vapor Density: Not Available
pH Factor: 8
Solubility: Completely
Evaporation Rate: Not Available
10. Stability And Reactivity
Stability: Stable
Hazardous Polymerization: Will not occur
Conditions To Avoid (Stability)
None Known
Incompatible Materials
Strong Oxidizing Agents
Hazardous Decomposition Products
CO, CO2, Oxides of Sulfur
Conditions To Avoid (Polymerization)
None Known
11. Toxicological Information
Conditions Aggravated By Exposure
Eye disease, skin disorders and allergies, chronic respiratory conditions.
12. Ecological Information
No Data Available...
13. Disposal Considerations
Dispose in accordance with applicable federal, state and local government regulations. Waste generators must
determine whether a discarded material is classified as a hazardous waste. USEPA guidelines for the classification
determination are listed in 40 CFR Parts 261.3. Additionally, waste generators must consult state and local hazardous
waste regulations to ensure complete and accurate classification.
MATERIAL SAFETY DATA SHEET Page 4 of 4
Sikament N
14. Transport Information
Proper Shipping Name
Not regulated by the USDOT
15. Regulatory Information
SARA Section 313 Notification
This product does not contain any ingredients regulated under Section 313 of the Emergency Planning and
Community Right-To-Know Act of 1986 or 40 CFR 372.
16. Other Information
HMIS Rating
Health: 1
F ir e : 0
Reactivity: 0
PP E: B
Revision/Preparer Information
MSDS Preparer: EHS Department
MSDS Preparer Phone Number: 201-933-8800
Disclaimer
The data in this Material Safety Data Sheet relates only to the specific material herein and does not relate to use in
combination with any other material r in any process. The information set forth herein is based on technical data
that Sika believes to be reliable as of the date hereof. Since conditions of use are outside our control, we make no
warranties, express or implied and assume no liability in connection with any use of this information. Nothing
herein is to be taken as a license to operate under or a recommendation to infringe any patents.
SIKA CORPORATION
Printed Using MSDS Generator鈩? 2000
|