Material Safety Data Sheet
Indu-Crete Part A
Emergency Telephone Number
2800 Enloe Street 800-535-5053
Hudson, WI 54016 Telephone Number for Information
800-577-6213
Hazardous Ingredients/Identity Information
Chemical Type: Polyalcohol emulsion, used with Indu-Crete Part B and Indu-Crete Part C
Chemical identity OSHA PEL ACGIH TLV
CAS # Percent
Vegetable oil-based substance Withheld >20% N/E N/E
(trade secret)
Butyl Benzyl Phthalate 85-68-7 10-20% N/E N/E
Secondary Alcohol Ethoxylate 84133-50-6 1-5% N/E N/E
10 mg/m3 10 mg/m3 (mist)
Glycerin 56-81-5 1-5%
5 mg/m3
(respirable)
Pine Oil 8002-09-3 0.5-1% N/E N/E
Propylene Glycol Monomethyl 108-65-6 <0.5% N/E N/E
Ether Acetate
Solvent Naphtha (Petroleum), 64742-95-6 <0.5% N/E N/E
Light Aromatic
n-Methyl-2-Pyrrolidone 872-50-4 <0.1% N/E N/E
N/E = not established
Physical Characteristics
~1 g/cm3 @ 68掳F
Boiling point Density
~205掳F
pH Solubility in water
~7.2 Miscible
Vapor Pressure Dynamic viscosity
~25 mmHg @ 68掳F ~210 mPa路s @ 68掳F
Appearance and odor: Gel-like white liquid with slight odor
Fire and Explosion Hazard Data
Flash point (Method used) >212掳F
Extinguishing Media: Dry chemical, carbon dioxide, foam, water
Special fire fighting procedures: Firefighters should wear self-contained breathing apparatus to
protect against potentially toxic and irritating fumes. Use cold-water spray to cool fire-exposed
containers to minimize the risk of rupture.
Unusual Fire and Explosion Hazards: Dry residue will support combustion. Toxic and irritating gases
or fumes may be given off if product is burned. Vapors or fumes may form explosive mixtures
with air.
Reactivity Data
Stability Stable Conditions to avoid: Protect from freezing
Indu-Crete A Material Safety Data Sheet Indue Sales Page 2 of 4
Oxidizing agents, reducing agents, acids, bases
Incompatibility (Materials to Avoid):
Hazardous Decomposition or Byproducts: Carbon monoxide, carbon dioxide, oxides of nitrogen, and
other undetermined aliphatic fragments will be formed if this product is heated to decomposition
or in a fire.
Hazardous Polymerization: Will not occur.
Health Hazard Data
Carcinogenicity: Not regulated as a carcinogen by OSHA, IARC, or NTP.
Effects, Signs, and Symptoms of Overexposure:
Primary route of exposure: Skin or eye contact, inhalation
Skin irritant. May cause symptoms of redness and itching. Repeated contact can
Skin contact:
cause dermatitis.
Eye contact: Irritation. Can cause reddening, tearing, and stinging. May cause corneal injury.
Inhalation: Respiratory tract irritation, with symptoms of coughing, sore throat, runny nose.
Prolonged inhalation of very large amounts could cause central nervous system
depression, with symptoms of nausea, lightheadedness, drowsiness, dizziness, loss of
coordination. Repeated and prolonged overexposure could cause brain and nervous
system damage.
Not likely to occur. May cause irritation, nervous system effects associated with
Ingestion:
solvent exposure. Product abdominal pain, nausea, vomiting, and diarrhea.
Medical Conditions Generally Aggravated by Exposure:
Pre-existing skin disorders, respiratory disorders, and eye disorders may be aggravated by
exposure to this product.
Emergency and First Aid Procedures:
Eyes: Immediately flush eyes with plenty of water for at least 15 minutes while holding eyelids
open. Get medical attention if eyes are burning, tearing, red, or otherwise irritated after flushing.
Skin: Remove contaminated clothing or shoes. Wash off with soap and water. Get medical
attention if irritation develops.
Inhalation: Move victim to fresh air and provide oxygen if breathing is difficult. Give artificial
respiration or oxygen if breathing problems develop. Get medical attention as needed.
Ingestion: Do NOT induce vomiting. If conscious, give two glasses of water (do not give
anything by mouth to an unconscious person). Seek medical attention immediately.
Indu-Crete A Material Safety Data Sheet Indue Sales Page 3 of 4
Precautions for Safe Handling and Use
Steps to Be Taken in Case Material is Released or Spilled
Clean up spills promptly, as material will be slippery.
Small spills: Use appropriate protective equipment. Stop the leak. Cover the spilled material
with inert material (cat litter, sand, clay, etc.) and collect for appropriate disposal.
Wash spilled area with water.
Large spills: Keep non-emergency personnel out of the area. Remove ignition sources. Notify
management. Put on protective equipment. Stop leak only if safe to do so.
Ventilate. Dike or dam the spill so it will not spread into drains, sewers, water
supplies, or soil. Do not allow spilled material or wash water to enter sewers, surface
waters, or groundwater. Wash spill area thoroughly.
Waste Disposal Method:
Follow federal, state, and local regulations. The material can be reacted with Part B to form an
inert material. Incineration is the recommended method of disposal. The material is not a
listed or characteristic hazardous waste under the Resource Conservation and Recovery Act, but
state laws may vary. The end use is responsible for determining whether a material containing
or derived from this should be classified as a hazardous waste.
Precautions to be Taken in Handling and Storing
Keep from freezing. Store between 32掳F and 120掳F.
Use only with adequate ventilation and personal protection. Wash thoroughly after handling.
Keep container closed when not in use. Protect from light. May form explosive peroxides.
Other Precautions:
Empty containers hold product residue. Do not heat or cut empty containers, as highly toxic
vapors and gases may be formed. Do not reuse without thorough commercial cleaning and
reconditioning. Thoroughly drain container before disposal.
Control Measures
Follow protective measures for Indu-Crete Part B.
Respiratory Protection:
Under normal use conditions, with general good ventilation and if material is not heated or
sprayed, no respirator is required. In inadequately ventilated areas or where the material is
sprayed, aerosolized, or heated and exposures may exceed occupational exposure limits, use a
NIOSH-approved respirator in accord with 29CFR1910.134.
At concentrations up to ten times the TLV or PEL, an air-purifying respirator with organic
vapor cartridges can be used, if the cartridge has an end-of-service-life indicator certified by
NIOSH or if a change-out schedule, reflecting conditions of use, has been developed.
Ventilation:
Provide adequate general (dilution) ventilation to limit worker exposure.
Indu-Crete A Material Safety Data Sheet Indue Sales Page 4 of 4
Protective Clothing:
Wear chemical resistant gloves appropriate to Indu-Crete Part B. Nitrile gloves are effective;
butyl rubber, neoprene and PVC are also suitable. Wear other protective clothing (boots,
coveralls) as needed to prevent skin contact.
Eye Protection:
Wear chemical safety goggles and a face shield if there is any possibility of splashing or
spraying. Wear appropriate eye protection whenever handling the product.
Work/Hygienic Practices:
Eyewashes and safety showers should be available for emergency use.
Transportation Requirements
Department of Transportation Classification:
Class 9, miscellaneous hazard. Packaging Group III
DOT Proper Shipping Name:
Environmentally Hazardous Substance, Liquid, n.o.s. (contains butyl benzyl phthalate).
Other Requirements: UN3082, ERG Guide 171.
Reportable Quantity: 552 lb (butyl benzyl phthalate)
Other Regulatory Controls
Components of this product are listed on the EPA/TSCA Inventory of Chemical Substances.
US EPA CERCLA Hazardous Substances (40CFR 302 butyl benzyl phthalate (RQ, 100 lbs)
SARA Section 311/312 Hazard Categories: Acute Health Hazard, Chronic Health Hazard
USEPA Emergency Planning and Community Right to Know Act SARA Title III, Section 302:
Extremely Hazardous Substances: this contains no listed components
USEPA Emergency Planning and Community Right to Know Act SARA Title III, Section 313:
n-methyl-2-pyrrolidone (<0.1%).
NFPA 704M Rating HMIS Rating
Health: 2 Health: 2
Flammability: 1 Flammability: 1
Reactivity: 0 Physical Hazard: 0
0=minimal, 1=slight, 2=moderate,
Other: N/A
3=serious, 4=severe
0=insignificant,1=slight, 2=moderate,3=high,,4=extreme
Date Prepared: 11 November 2005 Prepared by: Janet L. Keyes, CIH
The data in this material safety data sheet relate only to the specific material designated herein and do not relate to
use in combination with any other material or in any process. The information is believed to be correct as of the
date issued. Since the use of this information and the conditions of use of the product are not within the control of
Indue Sales and Services, it is the user鈥檚 obligation to determine procedures for safe use and disposal of the product
and to follow the appropriate safe procedures.
|