PARABOND M-5000
High Performance
Cove Base Adhesive
6. Press base firmly into place immediately after
ENVIRONMENTAL/PERFORMANCE:
application of adhesive.
鈥? Solvent Free
7. Wrapped base or rolled base should lay flat for 24
鈥? Non-hazardous
hours before application.
鈥? MICROBAN庐 Antimicrobial Protection
鈥? Freeze Thaw Stable
TROWEL SIZE:
鈥? Corner Wrap Capabilities
Use a 1/8鈥? square notched cove base trowel.
鈥? For All Vinyl and Rubber Cove Base
鈥? Trowels easily
COVERAGE:
鈥? Easy clean up
Approximately 150-200 liner feet of 4鈥? base per gallon
DESCRIPTION:
On Cartridges 鈥? Remove cap and insert cartridges in
Parabond M-5000 Acrylic Cove Base Adhesive is a
applicator. Use nozzle with 3 holes for 4鈥? and 5 holes for
premium solvent free adhesive that has been specifically
6鈥? base. Apply adhesive to back of cove base. Position or
developed for the permanent installation of rubber and
roll base immediately or within 20 minutes.
vinyl cove bases. This adhesive sets to an extremely
strong, water-resistant bond. M-5000 can be used over
CLEAN-UP:
most interior wall surfaces with the exception of vinyl wall
Wet adhesive may be removed immediately with a damp
covering and other similar non-porous surfaces that
cloth. If adhesive has dried, use a cloth moistened with
prevent the curing of any latex-based adhesive.
Mineral Spirits Do not allow solvent to penetrate the
M-5000 contains no hazardous or carcinogenic ingredients
seams; this can destroy the adhesive bond.
as defined by OSHA, Federal, State or Local Regulations
such as California Prop 65. M-5000 meets all
PHYSICAL PROPERTIES:
flammability requirements for a Class A Flame Spreading
Weight/Gallon 10.4
Rating as per ASTM-E84.
Consistency Heavy paste
Shelf Life One year @ 70掳F in un-opened container
DIRECTIONS:
1. Adhesive, cove base and job site must be
FOR MORE INFORMATION READ
conditioned at 65掳 - 80掳F for 48 hours before and
MATERIAL SAFETY DATA SHEET
after installation.
2. Use only on structurally sound surfaces, dry wall,
KEEP OUT OF REACH OF CHILDREN
plywood, paneling, masonry, plaster, etc.
3. Apply to surfaces that are clean, dry, and free
from dust, wax, grease, remove loose paint, WARRANTY:
plaster, old adhesive and other contaminates that Para-Chem鈥檚 only obligation shall be to replace or pay for
would interfere with a proper adhesion. any adhesive proved defective when authorized in writing
4. Cement or plaster must be thoroughly seasoned by the company. Beyond the purchase price of materials
and dry. supplied by us we assume no liability for any damages of
DO NOT APPLY OVER NON-POROUS SURFACES any kind and the user accepts the product 鈥渁s is鈥? and
SUCH AS MASONITE PLASTIC LAMINATES OR without warranties, expressed or implied. The suitability
VINYL WALL COVERINGS. of the product for an intended use shall be solely up the
5. With a 1/8鈥? square-notched spreader, spread on user. 10-31-02
back of base or wall surface.
ISO 9001 Certified
Corporate Address: PO Box 127 鈥? Simpsonville, SC 29681-0127 鈥? 800-763-7272 鈥? Fax: 864-228-1491
Manufacturing Facilities: Simpsonville, SC 鈥? Philadelphia, PA 鈥? Dalton, GA 鈥? Mansfield, TX 鈥? Adelanto, CA
www.parabond.com
MATERIAL SAFETY DATA SHEET Page 1
庐
Para-Chem , PO Box 127, Simpsonville, SC 29681
24-Hour Emergency Telephone: (864) 967-7691
SECTION 1. PRODUCT IDENTIFICATION
PRODUCT NAME: PARABOND庐 M-5000 COVE BASE ADHESIVE
CHEMICAL FAMILY: Water Base Adhesive
SECTION 2. HAZARDOUS INGREDIENTS AND EXPOSURE LIMITS
CAS % by
Chemical Name Number Weight ACGIH TLV OSHA PEL
None.
SECTION 3. HAZARDS IDENTIFICATION
PRIMARY ROUTES OF ENTRY: Eyes.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None known.
POTENTIAL HEALTH EFFECTS:
EYE CONTACT: May cause slight irritation.
SKIN CONTACT: No effect known.
INGESTION: Not likely to occur. If swallowed, no side effects known.
INHALATION: No effect known.
CHRONIC: None known.
CARCINOGENICITY: This product contains no ingredient listed as a carcinogen by IARC, NTP,
or OSHA.
SECTION 4. FIRST AID MEASURES
EYE CONTACT: Flush with water for 15 minutes. Contact a physician if irritation occurs.
SKIN CONTACT: Wash with soap and water.
INGESTION: Induce vomiting, contact a physician.
SECTION 5. FIRE-FIGHTING MEASURES
FLASH POINT (o)F: None.
LOWER FLAMMABLE LIMIT: None.
UPPER FLAMMABLE LIMIT: None.
FIRE-FIGHTING INSTRUCTIONS: Use protective clothing and self-contained breathing apparatus.
EXTINGUISHING MEDIA: Water fog, CO2, dry chemical, and chemical foam.
DECOMPOSITION PRODUCTS: Dried material may produce CO, CO2, H2O, NxO, and other
products from the burning of aromatic hydrocarbons.
MATERIAL SAFETY DATA SHEET Page 2
SECTION 6. ACCIDENTAL RELEASE MEASURES
STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Dispense sand, sawdust,
or vermiculite. Collect and place in waste container. Wash area thoroughly with water.
SECTION 7. HANDLING AND STORAGE
HANDLING: Use good hygienic practices. (Wash hands before eating, using washroom, or smoking.)
Keep out of the reach of children.
STORAGE: Store above 40oF.
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
PERSONAL PROTECTIVE EQUIPMENT:
EYE/FACE PROTECTION: Wear splash goggles if contact with material is likely.
SKIN PROTECTION: Wear gloves goggles if contact with material is likely.
RESPIRATORY PROTECTION: Not normally required with good ventilation.
ENGINEERING CONTROLS: Normal room ventilation.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
BOILING POINT (oF): 212
SPECIFIC GRAVITY (WATER = 1): 1.24
VAPOR PRESSURE: Same as water.
VAPOR DENSITY(air=1): Same as water.
% VOLATILE BY WEIGHT: 44
pH: 9.4
APPEARANCE AND ODOR: Light tan colored paste.
GRAMS VOLATILE ORGANIC COMPOUNDS/LITER OF COATING: 0 (Based on no solvent.)
GRAMS VOLATILE ORGANIC COMPOUNDS/LITER OF MATERIAL: 0 (Based on no solvent.)
SECTION 10. STABILITY AND REACTIVITY
CHEMICAL STABILITY: Stable.
POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: None known.
HAZARDOUS DECOMPOSITION PRODUCTS: None.
SECTION 11. TOXICOLOGICAL INFORMATION
This product has been tested for toxicity (acute inhalation; acute dermal; skin irritation; oral) and has
been found to be non-toxic as defined by The Federal Hazardous Substance Act, 16 CFR 1500.3.
MATERIAL SAFETY DATA SHEET Page 3
SECTION 12. ECOLOGICAL INFORMATION
No information available.
SECTION 13. DISPOSAL CONSIDERATIONS
Disposed of in accordance with Federal, State and Local regulations.
SECTION 14. TRANSPORT INFORMATION
For domestic transportation purpose, this product is not designated as a hazardous material by the
U.S. Department Of Transportation.
SECTION 15. REGULATORY INFORMATION
TSCA: All ingredients are listed.
SARA TITLE III:
Section 311 and 312 Health and Physical Hazards:
Immediate Delayed Fire Pressure Reactivity
[X] [] [] [] []
SECTION 16. OTHER INFORMATION
HMIS RATINGS: Health = 1 Flammability = 1
Reactivity = 0 Personal Protective Equipment = B
Hazard rating scale: 0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe
Para-Chem believes the statements, technical information and recommendations contained herein
are reliable. They are given without warranty or guarantee of any kind, expressed or implied.
DATE ISSUED: October 31, 2002 PREPARED BY: R. West
|