August 16, 2004
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Proin Drops
MSDS No.: 0009
I. Basic Information:
Manufacturer: Pegasus Laboratories, Inc.
1
Address: 8809 Ely Road
City, ST Zip: Pensacola, FL 32514 1 0
Emergency Contact: Chemtrec
Emergency Telephone Number: 800-424-9300
Contact: Carl Causey
Information Telephone Number: 850-478-2770
1
1
Last Update: 02/07/2003
0
X Liquid Gas Solid
Chemical State:
Pure X Mixture
Chemical Type:
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
X
56815 Glycerine (mist) 2-4 15 mg/m3 10 ppm NI
154416 Phenylpropanolamine Hydrochloride 2-4 NI NI NI
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
Phenylpropanolamine Hydrochloride is toxic when overdoses are ingested. Adverse effects may include dizziness, headache,
nausea, insomnia or restlessness, and increased blood pressure. The usual oral adult dose of phenylpropanolamine
hydrochloride is 25 mg every four hours, not to exceed a maximum of 150 mg in 24 hours.
Over exposure to glycerine may cause damage to, disorders to, or adversely affect the liver, kidneys or gastrointestinal tract.
IV. First Aid Measures:
Route(s) of Entry:
Contact, inhalation, and ingestion are primary routes of entry.
Health Hazards (Acute and Chronic):
Eyes: Contact with product may cause irritation and redness.
Skin: Contact with skin may cause irritation.
Inhalation: Inhalation may cause irritation, headache, nausea, and drowsiness.
Ingestion: Ingestion may cause irritation and nausea if administered in dosages other than prescribed.
Signs and Symptoms:
NI
Medical Conditions Generally Aggravated by Exposure:
NI
August 16, 2004
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Proin Drops
MSDS No.: 0009
Emergency and First Aid Procedures:
Eyes: Immediately flush eyes with large quantity of water for 10 to 15 minutes. Get medical attention.
Skin: Flush skin with plenty of water for at least 15 minutes, while removing contaminated clothing. Thoroughly clean clothing
and shoes before reuse.
Inhalation: Immediately remove victim to fresh air.
Ingestion: For an overdose, have victim drink water or milk to dilute. Call a physician immediately. Induce vomiting only if
advised by a physician.
Other Health Warnings:
NI
V. Fire Fighting Measures:
Flash Point: NI Lower Explosive Limit: NI Upper Explosive Limit: NI
F.P. Method: NI
Fire Extinguishing Media: dry chemical, foam, water spray/ fog, CO2
Special Fire Fighting Procedures:
Prevent human exposure to fire, fumes, smoke, and products of combustion. Evacuate non-essential personnel. Firefighters
should wear full-face, self-contained breathing apparatus and protective clothing. Prevent pollution of ground water from fire
control run-off.
Unusual Fire and Explosion:
NI
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
In case of spills, contain and dispose of in accordance with federal, state, and local regulations. Ventilate spill area and flush area
with water.
VII. Handling and Storage:
Precautions to be Taken:
Protect container against physical damage. Store in cool, dry area, inaccesible to children.
Other Precautions:
NI
VIII. Exposure Controls/Personal Protection:
Ventilitation Requirements:
Handle in well-ventilated area. Where excessive exposure is likely, use NIOSH/MSHA Approved protection equipment.
Personal Protective Equipment:
Protective Clothing: Wear gloves and protective clothing if there is potential for prolonged/ repeated skin contact.
Eye Protection: Wear safety glasses and chemical safety goggles whenever there is the possiblity of contact with the eyes.
August 16, 2004
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Proin Drops
MSDS No.: 0009
IX. Physical and Chemical Properties:
Boiling Point: NI Melting Point: NI
Evaporation Rate (Butyl Acetate = 1): NI Vapor Pressure (mm Hg.): NI
Specific Gravity (H20 = 1): 1.04000 Vapor Density (AIR = 1): NI
Solubility In Water: Soluble Apprearance and Odor: Clear; Vanilla odor
Other Information: Density = 8.7 lbs./gal.
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Avoid contact with bleaching agents and oxidizing agents.
Decomposition/By Products:
If product is burned, carbon monoxide, carbon dioxide and miscellaneous organic compounds are produced , some potentially
toxic.
Also emitted are very toxic fumes of HCl and NOX if heated to decomposition.
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
NI
XII. Ecological Information:
NI
XIII. Disposal Considerations:
Dispose of at an approved facility according to regulations under RCRA and in accordance with all federal, state, and local
regulations.
XIV. Transport Information:
NI
XV. Regulatory Information:
August 16, 2004
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Proin Drops
MSDS No.: 0009
OSHA STATUS: This product is hazardous under the criteria of the Federal OSHA Hazard Communication Standard 29 CFR
1910.1200.
TSCA STATUS: The ingredients of this product are on the TSCA inventory.
CERCLA REPORTABLE QUANTITY: None
SARA TITLE III:
SECTION 302 EXTREMELY HAZARDOUS SUBSTANCES: None
SECTION 311/312 HAZARD CATEGORIES:Immediate and delayed health hazard.
SECTION 313 TOXIC CHEMICALS: None
RCRA STATUS: If discarded in its purchased form, this product would not be a hazardous waste either by listing or by
characteristic. However, under RCRA it is the responsibilty of the product user to determine at the time of disposal, whether a
material containing the product or derived from the product should be classified as a hazardous waste (40 CFR 261.20-24)
XVI. Other Information:
Reason for Issue : New MSDS in the ANSI Z 400.1-1998 format.
NI = Not Indicated.
> = Greater Than.
The information and statements in this Material Safety Data Sheet are believed to accurately reflect the scientific evidence used in
making the hazard determination but is not to be construed as a warranty or representation for which we assume legal responsibility.
Additional information may be necessary or desirable depending on particular, exceptional or variable conditions or circumstances of
use or storage or because of locally applicable laws or government regulations. Therefore, you should use this informatin only as a
supplement to other information available to you and must make independent determinations of the suitability of the information for
your particular circumstance or conditions and of the completeness of the information available from all sources to assure both the
proper use of the material described herein and the safety and heath of employees.
|