Sartomer Company
Material Safety Data Sheet
Product: Esacure 1007 Revised Date: 05-11-2007
MSDS ID: S-002353 Replaces Date: None
01. GENERAL INFORMATION
Sartomer Company, Inc.
Oaklands Corporate Center
502 Thomas Jones Way
Exton, Pennsylvania 19341
Emergency phone numbers:
800/424-9300 (CHEMTREC)
610/692-8401 (Sartomer Co., Inc.)
Product information:
610/363-4100
GENERIC NAME
2-Methyl-1-(4-methylthiophenyl)-2-morpholinopropan-1-one
DOT PROPER SHIPPING NAME UN/NA NUMBER
Environmentally hazardous substance, solid, n.o.s. UN 3077
(2-methyl-1-(4-methylthiophenyl)-2-morpholinopropano-1-one)
DOT HAZARD CLASS PACKING GROUP
9 III
02. SUMMARY OF HAZARDS
CAUTION
PHYSICAL HAZARDS: Potential dust explosion hazard
ACUTE HEALTH EFFECTS: Suspect slight eye irritation hazard
(SHORT TERM) Suspect slight skin irritation hazard
Suspect inhalation hazard-particulate/dust
Not expected to be a skin absorption hazard
Suspect slight ingestion hazard
CHRONIC HEALTH EFFECTS: No data are available on the chronic health
(LONG TERM) effects of this material.
03. COMPONENTS
COMPONENT NAME CAS NUMBER COMPOSITION (WT %)
2-Methyl-1-(4-methylthiophenyl)-
2-morpholinopropan-1-one 71868-10-5 AP 100
04. PHYSICAL AND CHEMICAL DATA
BOILING POINT pH
GT 300C/527F N/AP
MELTING POINT DRY POINT
70-75C/158-167F N/AP
SPECIFIC GRAVITY (H20=1 AT 39.2F) VOLATILE CHARACTERISTICS
1.21 g/cm3 at 20C/68F Negligible
Date Printed: 05-11-2007 Page: 1 of 7
Sartomer Company
Material Safety Data Sheet
Product: Esacure 1007 Revised Date: 05-11-2007
MSDS ID: S-002353 Replaces Date: None
VISCOSITY UNITS, TEMP. SOLUBILITY IN WATER
AN/AP Insoluble
VAPOR PRESSURE STABILITY
N/AP Stable
VAPOR SP GR (AIR=1 AT 60 - 90F) HAZARDOUS POLYMERIZATION
N/AP Not expected to occur
APPEARANCE AND ODOR
White crystalline powder with slight characteristic odor
CONDITIONS AND MATERIALS TO AVOID
Direct sunlight, excessive light, moisture, oxidizing conditions, excessively
high temperatures, sparks and open flame, dusting conditions;
HAZARDOUS DECOMPOSITION PRODUCTS
Carbon monoxide and carbon dioxide may be released during decomposition or in
a fire involving this product.
05. OCCUPATIONAL EXPOSURE LIMITS
SUBSTANCE SOURCE DATE TYPE VALUE TIME
A PEL or TLV has not been established for this product; however, airborne
concentrations should not exceed the following limits:
Particulates not otherwise classified (PNOC):
OSHA PEL-TWA 5 mg/m3(respirable)
15 mg/m3(total)
ACGIH TLV-TWA 3 mg/m3(respirable)
10 mg/m3(inhalable)
06. FIRE AND EXPLOSION
FLASH POINT METHOD= AUTOIGNITION TEMP. METHOD=
N/AP N/AP
FLAMMABLE LIMITS (% VOLUME IN AIR)
LOWER: N/AP UPPER: N/AP
FIRE AND EXPLOSION HAZARDS
When mixed with air and exposed to an ignition source, sufficient dust may
become an explosion hazard. Use good housekeeping practices to avoid
rendering dust airborne and prevent electrostatic charge formation during
transfer and use of this material. Ensure that all equipment and containers
are adequately grounded. Vapors generated from overheating/decomposition may
be flammable and may cause fire/explosion if source of ignition is present.
EXTINGUISHING MEDIA
Chemical powders
Date Printed: 05-11-2007 Page: 2 of 7
Sartomer Company
Material Safety Data Sheet
Product: Esacure 1007 Revised Date: 05-11-2007
MSDS ID: S-002353 Replaces Date: None
Foam
CO2
Water spray
Water fog
SPECIAL FIREFIGHTING PROCEDURES
Do not enter fire area without proper protection. See section on
decomposition products possible. Fight fire from safe distance/protected
location. Apply aqueous extinguishing media carefully to prevent
frothing/steam explosion. Use water spray/fog for cooling. Avoid contact
with molten product to prevent serious burns. Avoid raising powdered
materials into airborne dust, creating an explosion hazard. Notify
authorities if liquid enters sewer/public waters.
07. HEALTH HAZARDS
ROUTES OF EXPOSURE
INHALATION -- PRIMARY ROUTE
Excessive exposure to particulate/dust from this product may cause
respiratory tract irritation such as cough, mucous production, sneezing,
shortness of breath.
EYE CONTACT -- PRIMARY ROUTE
Although no appropriate human or animal health effects data are known to
exist, this material is expected to cause slight eye irritation.
Symptoms of irritation may include excessive tearing, blinking, redness and a
scratchy feeling.
SKIN ABSORPTION
Although no appropriate human or animal health effects data are known to
exist, this material is not expected to be a health hazard by skin
absorption.
SKIN IRRITATION -- PRIMARY ROUTE
Although no appropriate human or animal health effects data is known to
exist, this material is not expected to be a skin irritant.
Symptoms of irritation may include a slight redness or rash and swelling of
the affected area.
INGESTION
Although no appropriate human or animal health effects data are known to
exist, this material is expected to be a slight ingestion hazard.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
No additional medical information found.
08. PROTECTIVE EQUIPMENT / CONTROL MEASURES
RESPIRATORY PROTECTION
NIOSH/MSHA approved dust or mist respirator should be used if airborne
particulate is generated when handling this material.
Date Printed: 05-11-2007 Page: 3 of 7
Sartomer Company
Material Safety Data Sheet
Product: Esacure 1007 Revised Date: 05-11-2007
MSDS ID: S-002353 Replaces Date: None
EYE PROTECTION
Dust service goggles should be worn to prevent mechanical injury to eyes due
to airborne particles which may be associated with this product.
SKIN PROTECTION
Depending on the conditions of use, protective gloves, apron, boots, head
and face protection should be worn. This equipment should be cleaned
thoroughly after each use.
ENGINEERING CONTROLS
Provide local exhaust or general room ventilation to minimize exposure to
dust. If mechanical ventilation is used, electrical systems should conform to
National Electric Code.
OTHER HYGIENIC PRACTICES
Emergency eye wash fountains and safety showers should be available in the
immediate vicinity of any potential exposure.
OTHER WORK PRACTICES
No special work practices are needed beyond the above recommendations under
anticipated conditions of normal use.
09. EMERGENCY AND FIRST AID
INHALATION
Remove victim to fresh air immediately. Obtain emergency medical attention
if breathing difficulty persists beyond 15 minutes.
EYE CONTACT
In case of eye contact with this solid material, immediately rinse with
clean water for 20-30 minutes. Retract eyelids often. Obtain emergency
medical attention if pain, blinking, tears or redness persist.
SKIN CONTACT
Remove contaminated clothing as needed. Wash skin thoroughly with mild
soap/water. Flush with lukewarm water for 15 minutes. If sticky, use waterless
cleaner first.
INGESTION
If large quantity swallowed, give lukewarm water (pint) if victim completely
conscious/alert. Do not induce vomiting/risk of damage to lungs exceeds
poisoning risk. Obtain emergency medical attention.
EMERGENCY MEDICAL TREATMENT PROCEDURES
If eye pain, blinking, tears, or redness continue, patient should contact
ophthalmologist.
10. SPILL AND DISPOSAL
PRECAUTIONS IF MATERIAL IS SPILLED OR RELEASED
Date Printed: 05-11-2007 Page: 4 of 7
Sartomer Company
Material Safety Data Sheet
Product: Esacure 1007 Revised Date: 05-11-2007
MSDS ID: S-002353 Replaces Date: None
Released material poses a dust explosion hazard if it becomes airborne in the
presence of an ignition source. Extinguish all ignition sources. On land
sweep/shovel into suitable disposal containers or vacuum using equipment
which avoids ignition risk. Avoid making dust. On water, contain/minimize
dispersion/collect. Report per regulatory requirements.
WASTE DISPOSAL METHODS
This product is not listed as a hazardous waste. To the best of our
knowledge, this product does not meet the criteria of a RCRA hazardous waste
when discarded in its purchased form (see 40 CFR 261). However, under RCRA it
is the responsibility of the user of a product to determine at the time of
disposal whether the product meets any of the criteria of a hazardous waste.
This is because the manner in which a product is used, processed, etc. may
alter it so that it becomes a hazardous material. Comply with
federal/state/local regulations for solid waste disposal. Incinerate or
landfill solids at permitted sites. Use registered transporters.
11. ADDITIONAL PRECAUTIONS
HANDLING AND STORAGE PROCEDURES
Store product in a dry, well ventilated area away from strong oxidizers.
Store at temperatures below product's melting point. Keep product away from
direct sunlight, heat, sparks, open flame, and other ignition sources. Keep
containers tightly closed and prevent contamination with foreign materials.
For optimum results, use within 6 months of receipt. This produc is not
expected to present an explosion hazard during normal transportation and
storage operations. However, when dispersed in air and subject to sufficient
energy of ignition, it may pose a dust explosion hazard. Minimize the
potential for dust explosion by eliminating/controlling ignition sources
(bond and ground), and by using good housekeeping practices during storage,
transfer, handling, and use to avoid excessive dust accumulation. Electrical
equipment must be grounded and conform to the National Electric Code. In
instances where this material is bulk conveyed, or where processing may
result in a dusty atmosphere, refer to the latest edition of the National
Fire Protection Association (NFPA) 654 publication, "Standard for the
Prevention of Fire & Dust Explosions in the Chemical, Dye, Pharmaceutical,
and Plastics Industries" for complete discussion of dust explosion prevention
and control measures.
DECONTAMINATION PROCEDURES
Follow standard plant procedures or supervisor's instructions for
decontamination operations.
12. LABEL INFORMATION
USE STATEMENT
FOR INDUSTRIAL USE ONLY
SIGNAL WORD
CAUTION
PHYSICAL HAZARDS
POTENTIAL DUST EXPLOSION HAZARD
HEALTH HAZARDS
Date Printed: 05-11-2007 Page: 5 of 7
Sartomer Company
Material Safety Data Sheet
Product: Esacure 1007 Revised Date: 05-11-2007
MSDS ID: S-002353 Replaces Date: None
INHALATION HAZARD - PARTICULATE/DUST
PRECAUTIONARY MEASURES
DO NOT HANDLE NEAR HEAT, SPARKS, OR OPEN FLAME.
PREVENT ELECTROSTATIC DISCHARGE FORMATION.
AVOID ACCUMULATION OF DUST IN ENCLOSED SPACE.
KEEP CONTAINER CLOSED WHEN NOT IN USE.
AVOID CONTACT WITH EYES, SKIN AND CLOTHING.
DO NOT BREATHE DUST.
USE ONLY WITH ADEQUATE VENTILATION/PERSONAL PROTECTION.
WASH THOROUGHLY AFTER HANDLING.
BEFORE USING PRODUCT, READ MATERIAL SAFETY DATA SHEET (MSDS).
13. SUPPLEMENT
NPCA HMIS RATING
Health 1
Flammability (dust) 1
Reactivity 1
Personal protection E (safety glasses with side shields or
dust service goggles, gloves, dust
respirator)
REGULATORY INFORMATION
TSCA STATUS
TSCA status: All components of this product are listed, or excluded from
listing, on the United States Environmental Protection Agency Toxic Substances
Control Act (TSCA) inventory.
INTERNATIONAL STATUS
Australia (AICS): included on inventory
Canada (DSL): included on inventory
China (IECSC): included on inventory
Europe (EINECS): included on ELINCS
Japan (ENCS): included on inventory
Korea (ECL): included on inventory
New Zealand (NZIoC): included on inventory
Philippines (PICCS): included on inventory
*Note - qualifiers and codes used in this MSDS
EQ = Equal; AP = Approximately; LT = Less Than; GT = Greater Than;
TR = Trace; UK = Unknown; N/AP = Not Applicable; N/P = No Applicable
Information Found; N/DA = No Data Available
14. DISCLAIMERS
Some of the information presented and conclusions drawn herein are from
sources other than direct test data on the product itself. The information in
this MSDS was obtained from sources which we believe are reliable. However,
the information is provided without any warranty, express or implied,
Date Printed: 05-11-2007 Page: 6 of 7
Sartomer Company
Material Safety Data Sheet
Product: Esacure 1007 Revised Date: 05-11-2007
MSDS ID: S-002353 Replaces Date: None
regarding its correctness. The conditions or methods of handling, storage, use
and disposal of the product are beyond our control and may be beyond our
knowledge. For this and other reasons, we do not assume responsibility and
expressly disclaim liability for loss, damage or expense arising out of or in
any way connected with the handling, storage, use or disposal of the product.
This MSDS was prepared and is to be used only for this product. If the
product is used as a component in another product, this MSDS information may
not be applicable. This MSDS has been prepared in accordance with the
requirements of the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Date Printed: 05-11-2007 Page: 7 of 7
|