MATERIAL SAFETY DATA SHEET
(This MSDS complies with 29 CFR 1910.1200)
Product Name: BC 6128 Hi-Heat Surface Coat Hardener BCC PRODUCTS, INC.
Product Class: Amine curing agent 2140 Earlywood Drive
Issue Date: 02/16/04 P.O. Box 327
Approved By: Thomas E. Evans Franklin, IN 46131
317-736-4090
24 HOUR EMERGENCY NO. 1-800-424-9300 CHEMTREC
SECTION 1 - HAZARDOUS INGREDIENTS
Chemical Name Wt. % OSHA (PEL) ACGIH (TLV) CAS NO.
(optional)
Triethylene Tetramine (TETA) N.E. N.E. 0112-24-3
1,3 Bis (Aminomethyl) Cyclohexane N.E. N.E. 2579-20-6
1-Methyl Imidazole N.E. N.E. 00616-47-7
1,3 Dihydroxybenzene N.E. N.E. 108-46-3
1,8 Diamino-P-Methane N.E. N.E. 008-52-4
SECTION 2 - PHYSICAL DATA
Boiling Point: > 400 掳 F Specific Gravity (H20=1): 1.0
Vapor Pressure (mm Hg): N.D.A. Vapor Density (Air = 1): N.D.A.
Solubility in Water: Moderate Reactivity in Water: Negligible
Appearance and odor: Amber color/Amine odor
SECTION 3 - FIRE AND EXPLOSION HAZARD
N.E.
Flash Point: > 225 掳 F Flammable Limit: LEL:
Method Used: TCC N.E.
UEL:
(In Air % by volume)
Auto Ignition Temperature: N.A.
Extinguishing Media: Carbon Dioxide, dry chemical, chemical foam, water spray.
Fire & Explosion Hazards: Decomposition and combustion products may be toxic.
Fire Fighting Procedures: Fire fighters must wear self-contained breathing apparatus to
protect against toxic and irritating vapors. Full protective clothing
should also be worn.
SECTION 4 - REACTIVITY DATA
Stability (Conditions to avoid): Stable.
Incompatibility (Materials to avoid): Strong acids, peroxides and other oxidizing agents.
Hazardous Decomposition Products: Carbon monoxide from incomplete burning.
Hazardous Polymerization (Materials to avoid): Will not occur.
N.E. - Not Established N.D.A. - No Data Available N.A . - Not Applicable
BC 6128 Hi-Heat Surface Coat HARDENER - Page 2
SECTION 5 - ENVIRONMENTAL AND DISPOSAL INFORMATION
Spill: Using recommended protective equipment, take up with absorbent material. Dike to contain. Flush
area with 5% acetic acid.
Disposal: Use approved incineration in accordance with federal, state and local environmental regulations.
Material must be disposed of in approved land fill.
SECTION 6 - HEALTH AND FIRST AID INFORMATION
FIRST AID
Routes of Entry
Inhalation: Remove victim to uncontaminated area, administer oxygen if necessary. Seek medical
attention.
Eyes: Flush with water for 15 minutes. Seek medical attention.
Skin: Remove contaminated clothes and wash affected areas with soap and water. Seek medical
attention.
Ingestion: DO NOT Induce vomiting. Drink large quantity of milk. Seek medical attention.
EFFECTS OF OVER EXPOSURE
Acute: Irritation, dermatitis, allergic skin reactions.
Chronic: Repeated, excessive exposure may cause sensitization.
Potential Carcinogen: NTP (National Toxicology Program) : No ; IARC (Monographs): No; OSHA: No
SECTION 7 - SPECIAL HANDLING & STORAGE PRECAUTIONS
Should be stored in a ventilated storage area between 70-80 掳 F. Avoid excessive temperatures. Do not store in direct sunlight.
Keep away from oxidizing agents and open flame.
SECTION 8 - SPECIAL PROTECTION INFORMATION
Respiratory Protection: Use NIOSH approved respirator, with organic vapor cartridges.
Ventilation: Local exhaust.
Eye Protection: Fitted chemical goggles, or safety glasses.
Personal Protection: Rubber gloves, boots and rubber apron to avoid skin contact. Contaminated clothing or
equipment should be cleaned or disposed of, after use.
Hygienic Practices: Educate and train employees on safe use of product. Shower and eye wash station should
be available.
The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and
use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred by use of this material. It is
the responsibility of the user to comply with all applicable federal, state, and local laws and regulations.
|