MATERIAL SAFETY DATA SHEET
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
CHS Inc. Transportation Emergency (CHEMTREC): 1-800-424-9300
P.O. Box 64089 Technical Information: 1-651-355-8443
Mail station 525 MSDS Information: 1-651-355-8438
St. Paul, MN 55164-0089
PRODUCT NAME: White Oil B MSDS: 0134-H9A0 - Rev.B (4.15.05)
COMMON NAME: Technical light white mineral Oil CHEMICAL FORMULA: Mixture
CHEMICAL NAME: White Mineral Oil CHEMICAL FAMILY: Hydrocarbon
Section 2 - COMPOSITION AND INFORMATION ON INGREDIENTS
INGREDIENTS PERCENTAGES PEL (OSHA) TLV (ACGIH) CAS #
(by weight)
Oil, White Mineral 99-100% N/A TWA (Oil Mist) 8042-47-5
5 mg/m3
dl+ tocopherol (Vitamin E) <0.1% N/A N/A 59-02-9
(stabilizer)
(TWA) - Time Weighted Average is the employee鈥檚 average airborne exposure in any 8-hour work shift of a 40-hour workweek, which shall not be exceeded.
(STEL) - Short Term Exposure Limit is the employee鈥檚 15-minute time weighted average exposure which shall not be exceeded at any time during a work day unless another time limit
is specified.
Section 3 - HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
POTENTIAL HEALTH EFFECTS
ROUTES OF ENTRY: (Eye Contact, Dermal, Inhalation.)
ACUTE EFFECTS OF OVER EXPOSURE:
Eyes - Contact with eyes may cause irritation.
Skin - Contact with skin may cause irritation.
Inhalation - May cause irritation of the nose and throat.
Ingestion - May cause nausea and vomiting. Large quantities may affect the central nervous system.
CHRONIC EFFECTS OF OVER EXPOSURE: No adverse effects anticipated.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Existing dermatitis and respiratory conditions.
CARCINOGENICITY: NTP: No IARC: No OSHA: No
Page 1 of 4
White Oil B
Section 4 - FIRST AID MEASURES
EMERGENCY AND FIRST AID PROCEDURES:
Eye Contact - If material comes in contact with the eyes, immediately wash the eyes with large amounts of water for 15
minutes, occasionally lifting the lower and upper lids. Get medical attention.
Skin Contact - If the material comes in contact with the skin, wash the contaminated skin with soap and water promptly. If the
material penetrates through clothing, remove the clothing and wash the skin with soap and water promptly. If irritation persists
after washing, get medical attention immediately.
Inhalation - If person breathes in large amounts of material, move the exposed person to fresh air at once. If breathing has
stopped, perform artificial respiration. Keep the person warm and at rest. Get medical attention as soon as possible.
Ingestion - If material has been swallowed, do not induce vomiting. Get medical attention immediately.
Section 5 - FIRE - FIGHTING MEASURES
FLASH POINT: >275掳F (>135掳C) AUTO IGNITION TEMP: >500掳 F
FLAMMABLE LIMITS IN AIR LOWER UPPER
% BY VOLUME N/A N/A
EXTINGUISHING MEDIA: Use water spray to cool fire-exposed surfaces and to protect personnel. Use foam, dry chemical or water
spray (fog) to extinguish fire.
SPECIAL FIRE FIGHTING PROCEDURES: When fighting fires wear full turnout gear and self-contained breathing apparatus.
Water may cause splattering. Material floats on water.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Toxic fumes gases or vapors may evolve on burning.
HAZARD RATINGS: NFPA 704: Health- 0 Fire- 1 Reactivity- 0
HMIS: Health- ___ Fire- ___ Reactivity-___
Section 6 - ACCIDENTAL RELEASE MEASURES
STEPS TO TAKE IF MATERIAL IS RELEASED OR SPILLED: Personal protective equipment should be worn. Ventilate area if
confined or poorly ventilated. Contain with dikes or absorbent to prevent migration to sewers/streams. Take up small spill with dry
chemical absorbent; large spills may require pump or vacuum prior to absorbent. May require excavation of severely contaminated soil.
Avoid contact with skin and eyes.
Section 7 - HANDLING AND STORAGE
HANDLING AND STORING: Store in closed container away from all ignition sources. Handling temperatures should not exceed
175掳F (80掳C). Wash thoroughly after handling. Do not store at temperatures exceeding 113掳F (45 C). Odorous and toxic fumes may
form from the decomposition of this product if stored at excessive temperatures for extended periods of time. Open containers carefully
and only in well-ventilated areas or use appropriate respiratory protection. Store in well ventilated area.
Page 2 of 4
White Oil B
Section 8 - EXPOSURE CONTROL - PERSONAL PROTECTION
ENGINEERING CONTROLS: Ventilate to control mists and vapors below exposure limits.
RESPIRATORY EQUIPMENT: Normally not required, if exposure limits are exceeded use a NIOSH approved organic vapor
respirator. Self-contained breathing apparatus is recommended for entry into confined spaces or other poorly ventilated areas and for
large spill clean-up sites.
EYE PROTECTION: Chemical goggles or face shield recommended to minimize eye contact.
PROTECTIVE CLOTHING: Impervious (nitrile) gloves recommended when handling material to minimize exposure. Long sleeve
shirts, chemically protective aprons and chemically protective boots are recommended for contact exposure or spill clean-up. Do not wear
watches, rings or similar apparel that could entrap the material next to the skin.
OTHER (SAFETY SHOWERS, EYE WASH STATIONS, ETC.): Water should be available for flushing and washing when
exposure exists. Launder soiled clothes. Discard shoes or other leather articles saturated with the material.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Colorless liquid ODOR: Odorless
BOILING POINT: N/D SPECIFIC GRAVITY (water=1): 0.8500 - 0.8800
VAPOR PRESSURE: <1 mm Hg 68掳 F VAPOR DENSITY (air=1): N/D
SOLUBLE IN WATER: Insoluble EVAPORATION RATE (ether=1): <1
Section 10 - STABILITY AND REACTIVITY
pH: N/D
STABILITY:
STABLE X (At room temperature and pressure. See handling and storage section)
UNSTABLE
INCOMPATIBILITY -
CONDITIONS TO AVOID: See handling and storage section.
MATERIALS TO AVOID: Acids, oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Smoke, carbon monoxide, aldehydes, hydrogen sulfide and alkyl mercaptans may
be released. Under combustion conditions, oxides of the following elements will be formed: Magnesium, calcium, nitrogen, sulfur, and
carbon.
HAZARDOUS POLYMERIZATION: Will not occur.
Section 11 - TOXICOLOGY INFORMATION
Please refer to Section 3 for available information on potential health effects.
Note: CHS Inc. has not conducted specific toxicity tests on this product.
Section 12 - ECOLOGICAL INFORMATION
No specific ecological data are available for this product. Please refer to Section 6 for information regarding accidental
releases and Section 15 for regulatory reporting information.
Page 3 of 4
White Oil B
Note: CHS Inc. has not conducted specific ecological tests on this product.
Section 13 - DISPOSAL CONSIDERATION
WASTE DISPOSAL PROCEDURES: Place contaminated materials in a disposable container and dispose of in accordance with
Local, State and Federal environmental regulations.
Section 14 - TRANSPORTATION
DOT PROPER SHIPPING NAME: N/A DOT HAZARD CLASS: N/A
DOT IDENTIFICATION NUMBER: N/A DOT EMER. RESPONSE GUIDE NO.: N/A
Section 15 - REGULATORY INFORMATION
This product does not contain toxic chemicals subject to the reporting requirements of SARA Section 313 of the Emergency Planning and
Community Right-To-Know Act of 1986 and of 40 CFR 372.
CAS Number Chemical Name Percent by Weight
N/A
SARA SECTION 311-312 HAZARD CATEGORIES (40 CFR 370.2):
FIRE: No SUDDEN RELEASE OF PRESSURE: No REACTIVE: No ACUTE: No CHRONIC: No
Section 16 - OTHER INFORMATION
Prepared By: Norm Rath Date: April 15, 2005
Approved by: Hue Lam Supercedes: 5/3/99
Title: EHS Compliance Specialist Reason for Issue: Formulation review
THE INFORMATION CONTAINED IN THIS MSDS RELATES ONLY TO THE SPECIFIC MATERIAL IDENTIFIED. IT
DOES NOT COVER USE OF THAT MATERIAL IN COMBINATION WITH ANY OTHER MATERIAL OR IN ANY
PARTICULAR PROCESS. IN COMPLIANCE WITH 29 C.F.R. 1910.1200(g), CHS INC. HAS PREPARED THIS MSDS IN
SEGMENTS, WITH THE INTENT THAT THOSE SEGMENTS BE READ TOGETHER AS A WHOLE WITHOUT TEXTUAL
OMISSIONS OR ALTERATIONS. CHS INC. BELIEVES THE INFORMATION CONTAINED HEREIN TO BE ACCURATE,
BUT MAKES NO REPRESENTATION, GUARANTEE, OR WARRANTY, EXPRESS OR IMPLIED, ABOUT THE
ACCURACY, RELIABILITY, OR COMPLETENESS OF THE INFORMATION OR ABOUT THE FITNESS OF CONTENTS
HEREIN FOR EITHER GENERAL OR PARTICULAR PURPOSES. PERSONS REVIEWING THIS MSDS SHOULD MAKE
THEIR OWN DETERMINATION AS TO THE MATERIAL鈥橲 SUITABILITY AND COMPLETENESS FOR USE IN THEIR
PARTICULAR APPLICATIONS.
Page 4 of 4
|