MSDS Material Safety Data Sheet
Provident Dental Products
ISIS SP Paste Opaque 1 3
Page of
MSDS Number: 951 Revision Date: 02/01/06
1 PRODUCT AND COMPANY IDENTIFICATION
Product Name: ISIS SP Paste Opaque
Revision Date: 02/01/06
MSDS Number: 951
Product Use: Dental restorations
Provident Dental Products
500 Memorial Drive
Somerset, NJ 08873
For MSDS assistance:
Chemtrec: (800) 424-9300 (24 hours/7 days)
Chemtrec International: (202) 483-7616
For Emergencies, call 911 immediately (in the US).
2 COMPOSITION/INFORMATION ON INGREDIENTS
CAS # Component
12001-21-7 Dental Porcelain >65%
56-81-5 Glycerine <10%
107-88-0 Butanediol <25%
This material does not contain any forms of crystalline silica. In addition to silicon (Si)
and oxygen (O), dental porcelains comprise the following chemical elements: Al, K, Na, Ca,
and may also comprise Li, Mg, Ba, Ce, Ti, Zr, Sn, Y, B, F and Fe. All these elements are
not present in their pure or individual oxide forms but rather chemically bonded together
within insoluble alumo-silicate glass matrix. By convention the composition of dental
porcelain, same as composition of many other glass-ceramic materials, is still reported on
individual oxide basis. In that representation composition of dental porcelain may be given
as about 50-80% of SiO2, about 5-15% of Al2O3 and the balance comprised of chemical
constituents listed above and below. Dental porcelain also contains small amounts of non-
silica inclusions: pigments, opacifiers, opalescing and fluorescing agents, which are based
on crystalline forms of TiO2, ZrO2, Al2O3, zirconium silicate (ZrSiO4) and yttrium silicate
(Y2SiO5). In the fired state of dental porcelain these components are fused and completely
encapsulated in chemically durable, insoluble glass matrix specifically designed and tested
to resist wear and corrosion in oral environment.
OSHA Regulatory Status: This MSDS contains valuable information critical to the safe
handling and proper use of the product. This MSDS should be retained and made available for
employees and other users of this product.
3 HAZARDS IDENTIFICATION
Route of Entry: Inhalation, Eye contact, Skin contact, Ingestion
Target Organs: Lungs
Inhalation: May irritate respiratory system.
Skin Contact: May irritate skin. May cause dermatisis.
Eye Contact: Airborne dust may irritate eyes.
Ingestion: May irritate digestive system.
4 FIRST AID MEASURES
MSDS Material Safety Data Sheet
Provident Dental Products
ISIS SP Paste Opaque 2 3
Page of
MSDS Number: 951 Revision Date: 02/01/06
Inhalation: Remove to fresh air.
Skin Contact: Rinse with soap and water.
Consult a physician if irritation occurs.
Eye Contact: Flush with copious amounts of water for at least 15 minutes.
Consult an ophthalmologist or medical attention if necessary.
Ingestion: Rinse out mouth and drink plenty of water. Seek medical attention.
5 FIRE FIGHTING MEASURES
Non-flammable.
Use the correct fire fighting measures for the surrounding area.
6 ACCIDENTAL RELEASE MEASURES
Use personal protection recommended in Section 8. Isolate area to prevent unnecessary and unprotected personnel from
coming in contact with paste. Use absorbent material to pick up material.
7 HANDLING AND STORAGE
Handling Precautions: Do not inhale or ingest.
Storage Requirements: Keep container tightly closed when not in use.
Store in original container.
Store in room temperature.
Store away from heat, flame, and oxidizing agents.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls: Mix, grind, and/or polish in a well ventilated area or an area with a proper exhaust fan.
Protective Equipment: Use NIOSH-approved safety glasses and dust mask.
Protective gloves are recommended.
Exposure Guidelines/Other: This product has not been evaluated as a whole.
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Creamy, ivory/white paste with no odor
Physical State: Paste Boiling Point: Not available
Odor: odorless Freezing/Melting Pt.: Not available
pH: Not available Solubility: insoluble
Vapor Pressure: Not available Spec Grav./Density: 2.40 g/cm3
Vapor Density: Not available
Bulk Density:
Fusion Point:
Glass Transition Temperature:
MSDS Material Safety Data Sheet
Provident Dental Products
ISIS SP Paste Opaque 3 3
Page of
MSDS Number: 951 Revision Date: 02/01/06
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: None known
Materials to avoid (incompatability): None known
Hazardous Decomposition products: None known
Hazardous Polymerization: None known
11 TOXICOLOGICAL INFORMATION
Not available
12 ECOLOGICAL INFORMATION
Not available
13 DISPOSAL CONSIDERATIONS
This information applies to the material as manufactured; processing, use, or contamination may make the information
inappropriate, inaccurate, or incomplete.
Waste must be handled in accordance with all applicable regulations. State and local disposal regulations may differ from
federal disposal regulations. Dispose of container and unused contents in accordance with federal, state, and local
requirements.
14 TRANSPORT INFORMATION
Not available
15 REGULATORY INFORMATION
Not available
16 OTHER INFORMATION
The information and recommendations set forth herein (hereinafter "Information") are presented in good faith and believed in good faith and believed to be
correct as of the date hereof. Provident Dental Products however, makes no representations as to the completeness or accuracy of this information and
supplies it on the condition that the persons receiving same will make their own determinations as to its suitability for their purpose prior to use. In no event
will Provident Dental Products be responsible for damages of any nature whatsoever resulting from the use of or reliance upon this information.
END OF MSDS DOCUMENT
|