MATERIAL SAFETY DATA SHEET
Page: 1
LIGHT STABILIZED COATING- PART B
PRODUCT NAME: LIGHT STABILIZED COATING- PART B HMIS CODES: H F R P
PRODUCT CODE: LSC-B-0000 310C
================== SECTION I - MANUFACTURER IDENTIFICATION =================
MANUFACTURER'S NAME: Polymerica Inc.
: 3821 Collins Lane
ADDRESS
Louisville, KY 40245
: 4/1/08
EMERGENCY PHONE : 1-800-535-5053 DATE PRINTED
: 1-800-762-1678
INFORMATION PHONE
========== SECTION II - HAZARDOUS INGREDIENTS/SARA III INFORMATION =========
VAPOR PRESSURE WEIGHT
REPORTABLE COMPONENTS CAS NUMBER MM HG @ TEMP PERCENT
------------------------------------------------------------------------------------------------------------------------
Isophoronediamine 2855-13-2 N/A N/A 80% TO 90%
None Established
Polyoxypropylenediamine 9046-10-0 1 20 C 0% TO 10%
None Established
1,3-cyclohexanedimethanamine 2579-20-6 14 248 F 0% TO 10%
None Established
Decanedioic Acid, bis(2,2,6,6-tetramethyl-4-piperidinyl) ester 129757-67-1 <1 20 C 0% TO 10%
=============== SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS ============
BOILING RANGE: 200 F - 709 F SPECIFIC GRAVITY (H2O=1): 1.0033
VAPOR DENSITY: Not Determined. EVAPORATION RATE: Heavier than air
(Air=1).
COATING V.O.C.: 0.0 lb/gl MATERIAL V.O.C.: 0.0 lb/gl
SOLUBILITY IN WATER: Partial.
APPEARANCE AND ODOR: Low viscosity, clear to amber liquid with sharp ammoniacal
type odor.
================= SECTION IV - FIRE AND EXPLOSION HAZARD DATA ==============
FLASH POINT: 124C METHOD USED: PMCC
FLAMMABLE LIMITS IN AIR BY VOLUME- LOWER: 0.7 UPPER: 5
EXTINGUISHING MEDIA: Use foam, dry chemical, CO2.
SPECIAL FIREFIGHTING PROCEDURES
Material will not burn unless preheated. Clear fire area of all non-emergency personnel. Do not enter confined fire
space without full bunker gear (helmet with face shield, bunker coats, gloves and rubber boots), including a positive
pressure, NIOSH approved, self-contained breathing apparatus. Cool surrounding equipment, fire-exposed containers and
structures with water. Container areas exposed to direct flame contact should be cooled with large quantities of water
(500 gallons water per minute flame impingement exposure) to prevent weakening of container structure.
UNUSUAL FIRE AND EXPLOSION HAZARDS
MATERIAL SAFETY DATA SHEET
Page: 2
LIGHT STABILIZED COATING- PART B
Toxic fumes present when this material is in fire. Containers may rupture.
======================== SECTION V - REACTIVITY DATA =======================
STABILITY: Normally Stable.
CONDITIONS TO AVOID
Avoid strong oxidizing agents and epoxy resins under uncontrolled conditions and elevated temperatures.
INCOMPATIBILITY (MATERIALS TO AVOID)
Avoid contact with acids such as Hydrochloric or Sulfuric. Avoid strong oxidizing agents and epoxy resins under
uncontrolled conditions.
HAZARDOUS DECOMPOSITION OR BYPRODUCTS
Products of combustion/decomposition include oxides of carbon and nitrogen plus amines and unidentified organic
compounds.
HAZARDOUS POLYMERIZATION:
==================== SECTION VI - HEALTH HAZARD DATA =======================
INHALATION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Can cause severe irritation of respiratory tract.
SKIN AND EYE CONTACT HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Corrosive- Can cause burns, vapors can cause irritation.
SKIN ABSORPTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Corrosive- Can cause burns.
INGESTION HEALTH RISKS AND SYMPTOMS OF EXPOSURE
Can cause severe damage to mouth and throat.
HEALTH HAZARDS (ACUTE AND CHRONIC)
CARCINOGENICITY: NTP CARCINOGEN: IARC MONOGRAPHS: OSHA REGULATED:
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE
Skin contact may aggravate an existing dermatitis (skin condition). Overexposure to vapor, dust or mist may aggravate
existing respiratory conditions such as asthma, bronchitis, and inflammatory or fibrotic respiratory disease.
EMERGENCY AND FIRST AID PROCEDURES
Eyes: Flush immediatley for 15 minutes with large amounts of potable water. Get immediate medical attention.
Skin: Flush immediatley for 15 minutes with potable water. Remove contaminated clothing. Launder before reuse.
Discard contaminated shoes. Get medical attention if swelling and/or irritation occurs.
Ingestion: DO NOT induce vomiting. Give milk or water to dilute stomach contents. Get immediate medical attention.
Inhalation: Remove to fresh air. Get medical attention if effects persist.
=========== SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE ============
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Avoid contact. Allow only personnel wearing goggles, neoprene or rubber gloves, and protective clothing to clean up
MATERIAL SAFETY DATA SHEET
Page: 3
LIGHT STABILIZED COATING- PART B
spill. In confined areas a full face respirator is recommended. Absorb spill with clay, diatomaceous earth or other
absorbent material.
WASTE DISPOSAL METHOD
Place in covered container for disposal. Dispose in an approved incinerator or an approved landfill in accordance with
federal, state and local regulations.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Mechanical ventilation required if TLV is expected to be exceeded in confined areas. Avoid contact. Keep containers
tightly closed when not in use. Do not remove labels from empty containers. If mixtures A & B are allowed to remain in
mixing vessel past pot life deadline, heat and a strong reaction will result.
OTHER PRECAUTIONS
===================== SECTION VIII - CONTROL MEASURES ======================
RESPIRATORY PROTECTION
None needed under normal conditions of use.
VENTILATION
Mechanical ventilation is required if TLV is expected to be exceeded in confined areas.
PROTECTIVE GLOVES
Wear neoprene or natural rubber gloves.
EYE PROTECTION
NIOSH approved saftey glasses or goggles.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT
Body protection as necessary to prevent skin contact. Wash after handling. Provide eye wash fountain and saftey
shower.
WORK/HYGIENIC PRACTICES
Practice good industrial hygene. Wash with soap and water before eating or smoking.
========================= SECTION IX - DISCLAIMER ==========================
The product information contained herein is believed to be accurate as of the date of the Material Saftey Data Sheet,
and is provided without warranty, expressed or implied, as to the results of use of this information or the product to
which it relates. Recipient assumes all responsibility for the use of this information and the use (alone or in
combination with any other product), storage or disposal of the product, including any resultant personal injury or
property damage.
|