Material Safety Data Sheet
SECTION 1. CHEMICAL PRODUCT AND COMPANY INFORMATION
Page 1 of 5
MANUFACTURER:
BondPro Corporation Transportation Emergency
650 Brakke Drive Chemtrec: 800-424-9300
Hudson, WI 54016
Phone: 715-386-6206
Fax: 715-386-1462
Issued:07/12/03
TRADE NAME:
BondPak 2262 Adhesive Part A and Part B
Chemical Name: Epoxy Resin and Modified Polyamide Hardener
Chemical Family: Epoxy; Amine
CAS Number: Mixture
SECTION 2. HAZARDOUS INGREDIENTS
SUBSTANCE DESCRIPTION PERCENT ACGIH TLV
Part A
10 Mg/m3
Aluminum Powder (dispersed in resin) 45-55 as dust
EPOXY RESIN 50-60
Part B
Amine with not established TLV <10 None None
Hazards: Corrosive, Irritant
The components of this product are in compliance with the chemical with
the chemical notification requirements of TSCA.
SECTION 3. PHYSICAL AND CHEMICAL CHARACTERISTICS
BOILING POINT: >225潞F
VAPOR DENSITY: >1 (Air = 1)
VAPOR PRESSURE, mm/Hg: Nil
EVAPORATION RATE: <1 (BuAc=1)
SOLUBILITY IN WATER: Nil
SPECIFIC GRAVITY: 1.29 Water=1
PERCENT VOLATILE: 0% by vol
APPEARANCE & ODOR:
Part A: Grey Paste; Part B Amber Paste: ammoniacal odor
SECTION 4. FIRE AND EXPLOSION DATA
Flash Point > 200潞F (PPMCC)
Flammable Limits 鈥? LEL N/A
Flammable Limits 鈥? UEL N/A
Material Safety Data Sheet
BondPak 2262 Adhesive Part A and Part B Page 2 of 5
EXTINGUISHING MEDIA:
Water spray, Carbon dioxide, Dry chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES:
Avoid breathing smoke. In confined areas, full fire fighting equipment
including a NIOSH approved self-contained breathing apparatus. Cool
fire exposed containers with water.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Part A: Violent exothermic reaction may occur. Keep away from all
sources of heat and direct sunlight. Part B: None
SECTION 5. HEALTH HAZARD INFORMATION
Threshold Limit Value (TLV): Not established
ANSI Hazard Class: Part A: 4 Part B: 4
Signs and Symptoms of Exposure
Type of Exposure Part Signs and Symptoms
Acute Overexposure A Moderately irritation to skin and eyes.
Possible skin sensitizer
B Vapors are irritating to the eyes
Chronic Overexposure A Per-existing skin and eye disorder may
be aggravated.
B Unknown
Routes of Exposure
Inhalation A Not likely to produce adverse effects
due to low volatility
B Vapors are irritating to skin and eyes
Ingestion A Low order of toxicity
B Moderate toxicity; may cause burns of
mouth and throat.
Skin Absorption A Not likely to be adsorbed though the
skin in toxic amounts
B Repeated or prolonged exposure may be
harmful
Skin Contact A Moderately irritation; may cause skin
sensitization
B May cause chemical burns and /or develop
allergic skin reaction
Eye Contact A Moderately irritating
B Moderately irritating
Carcinogenicity
NTP A No
B No
IARC A No
B No
OSHA A No
B No
Material Safety Data Sheet
BondPak 2262 Adhesive Part A and Part B Page 3 of 5
the
SECTION 6. EMERGENCY AND FIRST AID PROCUEDURES
EYE CONTACT:
Immediately flush eyes with large amounts of water for 15 minutes while
holding eyelids open. Get immediate medical attention.
SKIN CONTACT:
Immediately wash skin with soap and large amounts of water. Remove
contaminated clothing. If signs/symptoms occur, call a physician.
Wash contaminated clothing before reuse and dispose of contaminated
shoes.
INHALATION:
Remove person to fresh air. Administer oxygen if necessary. If
signs/symptoms continue, call a physician.
IF SWALLOWED:
Do not induce vomiting. Give large doses of water. Get medical
attention.
SECTION 7. REACTIVITY DATA
Stability: Stable: X Unstable:
Conditions to Avoid: Elevated temperature
Incompatibility (materials to avoid): Strong oxidizing agents, strong
acids and bases
Hazardous Decompositions Products: Oxides of carbon and nitrogen
Hazardous Polymerization: May Occur: Will not Occur: X
Conditions to Avoid: Large mixtures in bulk. Curing process is
exothermic.
SECTION 8. SPILL AND LEAK PROCEDURES
Steps to be taken if Material is Spilled or released:
Avoid contact with liquid and vapors. Wipe with a cloth or collect on
absorbent material. For large spills, dike and contain. Pump or
shovel into salvage containers.
Waste Disposal Method:
Cure, then bury or incinerate. Remove salvage containers to a waste
disposal site operating in compliance to federal, state and local
regulators.
BondPak 2262 Adhesive Part A and Part B Page 4 of 5
Material Safety Data Sheet
SECTION 9. SPECIAL PROTECTION INFORMATION
For excessive vapor or to maintain below the TLV limit, NIOSH approved
respirator in compliance to 29 CFR 1920.134.
Ventilation: Local Exhaust: Yes
Mechanical: Yes
Other: As required
Protective Gloves: Impervious rubber
Eye Protection: Splash-proof chemical goggles
Other Protective Equipment: For prolonged exposure, impervious
clothing and shoes to minimum
personal contact. Eye wash
station: safety shower.
SECTION 10 SARA TITLE III INFORMATION
Section 302/304: Extremely Hazardous Substance
Component CAS# % RQ(lbs) TPQ (lbs)
NONE
CERCLA Section 102(a): Hazardous Substance
Component CAS# % RQ(lbs)
NONE
Section 313: Toxic Chemicals
Component CAS# %
Aluminum Powder 7429-90-5 45-55
SECTION 11. SPECIAL PRECAUTIONS
FOR INDUSTRIAL USE ONLY!
Warning Statements: Part A: May cause skin irritation; avoid
contact with eyes.
Part B: Corrosive. May cause sever eye burns.
Precaution to be taken in Handling and Storage:
Part A: Store at 40F or below in tightly sealed containers. Keep away
form all sources of heat and direct sunlight. Avoid contact with skin
and eyes. Use with adequate ventilation.
BondPak 2262 Adhesive Part A and Part B Page 5 of 5
Material Safety Data Sheet
Part B: Store in a cool, dry area in tightly closed containers. Avoid
contact with skin and eyes. Use with adequate ventilation. Use good
hygiene practices.
Other Precautions:
RCRA Status: Not considered to be a hazardous waste
CERCLA: Not listed
DOT Class: Part A: Not regulated
Part B: Corrosive Liquid, basic, Organic, N.O.S., UN
3267
The information in this Material Safety Data Sheet (MSDS) is believed
to be correct as of the date issued. BONDPRO CORPORATION MAKES
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for
determining whether the BondPro Corporation product is fit for a
particular purpose and suitable for user鈥檚 methods of use or
application. Given the variety of factors that can affect the use and
application of a BondPro
Corporation product, some of which are uniquely within the user鈥檚
knowledge and control, it is essential that the user evaluate the
BondPro Corporation product to determine whether it is fit for a
particular purpose and suitable for user鈥檚 method of use or
application.
BondPro Corporation provides information in electronic form as a
service to its customers. Due to the remote possibility that
electronic transfer may have resulted in errors, omissions or
alterations in this information, BondPro Corporation makes no
representations as to its completeness or accuracy. In addition,
information obtained from a database may not be as current as the
information in the MSDS available directly from BondPro Corporation.
|