Material Safety Data Sheet
SECTION 1. CHEMICAL PRODUCT AND COMPANY INFORMATION
Page 1 of 5
MANUFACTURER:
BondPro Corporation Transportation Emergency
650 Brakke Drive Chemtrec: 800-424-9300
Hudson, WI 54016
Phone: 715-386-6206
Fax: 715-386-1462
ISSUED: May 16, 2001
TRADE NAME:
BondPak 2362 Adhesive Part B Tan NS epoxy
SECTION 2. COMPOSITION/INFORMATION ON INGREDIENTS
SUBSTANCE DESCRIPTION PERCENT CAS#
Epoxy Resin 60.0 鈥? 100.0 25068-38-6
Kaolin 10.0 - 30.0 1332-58-7
The components of this product are in compliance with the chemical
notification requirements of TSCA.
SECTION 3. PHYSICAL DATA
BOILING POINT: N/A
VAPOR DENSITY: N/A
VAPOR PRESSURE: N/A
EVAPORATION RATE: N/A
SOLUBILITY IN WATER: nil
SPECIFIC GRAVITY: 1.36 Water=1
PERCENT VOLATILE: 0.00% by wt
pH: N/A
VISCOSITY: ca. 100.0 Centipoise
MELTING POINT N/D
APPEARANCE & ODOR:
Paste, off white, very slight epoxy odor.
SECTION 4. FIRE AND EXPLOSION HAZARD DATA
Flash Point N/A
Flammable Limits 鈥? LEL N/A
Flammable Limits 鈥? UEL N/A
Autoignition Temperature: N/D
EXTINGUISHING MEDIA:
Water spray, Carbon dioxide, Dry chemical, Foam
Material Safety Data Sheet
BondPak 2362 Adhesive Part B Page 2 of 5
SPECIAL FIRE FIGHTING PROCEDURES:
Wear full protective clothing, including helmet, self-contained,
positive pressure or pressure demand breathing apparatus, bunker coat
and pants, bands around arms, waist and legs, face mask, and protective
covering for exposed areas of the head.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
No unusual fire or explosion hazards are anticipated.
NFPA HAZARD CLASSIFICATION
HEALTH: 1 FIRE: 1 REACTIVITY: 1
UNUSUAL REACTION HAZARD: NONE
SECTION 5. REACTIVITY DATA
STABILITY: Stable
INCOMPATIBILITY 鈥? MATERIALS/CONDITIONS TO AVOID:
Heat is generated during cure. Do not cure a mass larger than 50
grams in a confined space to prevent a premature reaction (exotherm)
with production of intense heat and smoke.
HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon Monoxide and Carbon Dioxide, Hydrocarbons, Toxic Vapors, Gases
or Particulates.
SECTION 6. ENVIRONMENTAL INFORMATION
SPILL RESPONSE:
Refer to other sections of this MSDS for information regarding
physical and health hazards, respiratory protection, ventilation, and
personal protective equipment. Ventilate area. Collect spilled
material. Clean up residue. Place in a U.S. DOT-approved container.
RECOMMENDED DISPOSAL:
Incinerate uncured waste in an industrial or commercial incinerator.
Dispose of completely cured (or polymerized) material in a sanitary
landfill.
ENVIRONMENTAL DATA:
Not determined.
REGULATORY INFORMATION:
Volatile Organic Compounds: 0.0 gms/liter South Coast Air Quality Mgmt
Dist Method.
VOC Less H2O & Exempt Solvents: 0.0 gms/liter South Coast Air Quality
Mgmt
Dist Method.
Since regulations vary, consult applicable regulations or authorities
before disposal.
Material Safety Data Sheet
BondPak 2362 Adhesive Part B Page 3 of 5
EPCRA HAZARD CLASS:
FIRE HAZARD: No PRESSURE: No REACTIVITY: Yes ACUTE: Yes
CHRONIC: Yes
SECTION 7. SUGGESTED FIRST AID
EYE CONTACT:
Immediately flush eyes with large amounts of water for at least 15
minutes. Get immediate medical attention.
SKIN CONTACT:
Wash affected area with soap and water.
INHALATION:
If signs/symptoms occur, remove person to fresh air. If signs/symptoms
continue, call a physician.
IF SWALLOWED:
Do not induce vomiting. Drink two glasses of water. Call a physician.
SECTION 8. PRECAUTIONARY INFORMATION
EYE PROTECTION:
Wear vented goggles. Wear safety glasses with side shields.
SKIN PROTECTION:
Avoid skin contact. Wear appropriate gloves when handling this
material.
RECOMMENDED VENTILATION:
Use with appropriate local exhaust ventilation. Provide appropriate
local exhaust for grinding, cutting or sanding cured material.
Curing ovens must be exhausted to outdoors or to a suitable emission
control device. Provide sufficient ventilation to maintain emissions
below recommended exposure limits. If exhaust ventilation is not
adequate, use appropriate respiratory protection.
RESPIRATORY PROTECTION:
Avoid breathing of dust created by cutting, sanding or grinding.
Select one of the following NIOSH approved respirators based on
airborne concentration of contaminants and in accordance with OSHA
regulations: half-mask dust respirator, full-face dust respirator.
PREVENTION OF ACCIDENTAL INGESTION:
Wash hands after handling and before eating. Do not ingest.
RECOMMENDED STORAGE:
Store away from heat. Keep out of the reach of children.
Store in a cool place. Store away from acids. Store away from heat.
Store out of direct sunlight. Keep container dry. Keep container in
well-ventilated area. Keep out of the reach of children.
Material Safety Data Sheet
BondPak 2362 Adhesive Part B Page 4 of 5
FIRE AND EXPLOSION AVOIDANCE:
Keep container tightly closed.
OTHER PRECAUTIONARY INFORMATION:
For industrial or professional use only.
EXPOSURE LIMITS
INGREDIENT VALUE UNIT TYPE AUTH SKIN*
Epoxy Resin NONE NONE NONE NONE
Kaolin 2 MG/M3 TWA ACGIH
RESPIRABLE
Kaolin 10 MG/M3 TWA OSHAV
AS DUST OSHA VACATED PEL
Kaolin 15 MG/M3 TWA OSHA
AS TOTAL DUST
Kaolin 5 MG/M3 TWA OSHA
RESPIRABLE
*SKIN NOTATION:
Listed substances indicated with 鈥榊鈥? under SKIN refer to the potential
contribution to the overall exposure by the cutaneous route including
mucous membrane and eye, either by airborne or, more particularly, by
direct contact with the substance. Vehicles can alter skin absorption.
SOURCE OF EXPOSURE LIMIT DATA:
-ACGIH: American Conference of Governmental Industrial Hygienists
-OSHA: Occupational Safety and Health Administration
-OHSAV: Occupational Safety and Health Administration Vacated PEL.
Vacated Permissible Exposure Limits (PEL) are enforced as the
OSHA PEL in some states. Check with your local regulatory
authority.
-NONE: None Established
SECTION 9. HEALTH HAZARD DATA
EYE CONTACT:
Mild Eye Irritation: signs/symptoms can include redness, swelling,
pain, and tearing.
Dust created by cutting, grinding, sanding, or machining may cause
eye irritation.
SKIN CONTACT:
Allergic Skin Reaction: signs/symptoms can include redness, swelling,
blistering, and itching.
Mild Skin Irritation (after prolonged or repeated contact):
Material Safety Data Sheet
BondPak 2362 Adhesive Part B Page 5 of 5
signs/symptoms can include redness, swelling, and itching.
INHALATION:
Irritation (upper respiratory): signs/symptoms can include soreness of
the nose and throat, coughing and sneezing.
Vapors of the uncured product may cause irritation of the respiratory
system.
Dust from cutting, grinding, sanding or machining may cause irritation
of the respiratory system.
IF SWALLOWED:
Irritation of Gastrointestinal Tissues: signs/symptoms can include
pain, vomiting, abdominal tenderness, nausea, blood in vomitus, and
blood in feces.
Abbreviations: N/D - Not Determined N/A - Not Applicable CA -
Approximately
The information in this Material Safety Data Sheet (MSDS) is believed
to be correct as of the date issued. BONDPRO CORPORATION MAKES
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for
determining whether the BondPro Corporation product is fit for a
particular purpose and suitable for user鈥檚 methods of use or
application. Given the variety of factors that can affect the use and
application of a BondPro Corporation product, some of which are
uniquely within the user鈥檚 knowledge and control, it is essential that
the user evaluate the BondPro Corporation product to determine whether
it is fit for a particular purpose and suitable for user鈥檚 method of
use or application.
BondPro Corporation provides information in electronic form as a
service to its customers. Due to the remote possibility that
electronic transfer may have resulted in errors, omissions or
alterations in this information, BondPro Corporation makes no
representations as to its completeness or accuracy. In addition,
information obtained from a database may not be as current as the
information in the MSDS available directly from BondPro Corporation.
|