Material Safety Data Sheet
SECTION 1. CHEMICAL PRODUCT AND COMPANY INFORMATION
Page 1 of 5
MANUFACTURER:
BondPro Corporation Transportation Emergency
650 Brakke Drive Chemtrec: 800-424-9300
Hudson, WI 54016
Phone: 715-386-6206
Fax: 715-386-1462
USSUED: August 6, 2001
TRADE NAME:
BondPak 2362 Adhesive Part A Tan NS Epoxy
SECTION 2. COMPOSITION/INFORMATION ON INGREDIENTS
SUBSTANCE DESCRIPTION PERCENT CAS#
Aliphatic Polymer Diamine 40.0 鈥? 60.0 68911-25-1
Kaolin 30.0 鈥? 60.0 1332-58-7
Amorphous Silica 5.0 鈥? 10.0 67762-90-7
The components of this product are in compliance with the chemical with
the chemical notification requirements of TSCA. All applicable
chemical ingredients in this material are listed on the European
Inventory of Existing Chemical Substances (EINECS), or are exempt
polymers whose monomers are listed on EINECS.
SECTION 3. PHYSICAL DATA
BOILING POINT: N/A
VAPOR DENSITY: N/A
VAPOR PRESSURE: N/A
EVAPORATION RATE: N/A
SOLUBILITY IN WATER: nil
SPECIFIC GRAVITY: 1.29 Water=1
PERCENT VOLATILE: 0.00% by wt
pH: N/D
VISCOSITY: 55000-70000 centipoise
MELTING POINT N/D
APPEARANCE & ODOR:
Paste, tan, pungent odor.
SECTION 4. FIRE AND EXPLOSION HAZARD DATA
Flash Point N/A
Flammable Limits 鈥? LEL N/A
Flammable Limits 鈥? UEL N/A
Autoignition Temperature: N/D
Material Safety Data Sheet
BondPak 2362 Adhesive Part A Page 2 of 5
EXTINGUISHING MEDIA:
Water, Carbon dioxide, Dry chemical, Foam
SPECIAL FIRE FIGHTING PROCEDURES:
Wear full protective clothing, including helmet, self-contained,
positive pressure or pressure demand breathing apparatus, bunker coat
and pants, bands around arms, waist and legs, face mask, and protective
covering for exposed areas of the head.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
No unusual fire or explosion hazards are anticipated.
NFPA HAZARD CLASSIFICATION
HEALTH: 2 FIRE: 0 REACTIVITY: 1 UNUSUAL REACTION HAZARD: NONE
SECTION 5. REACTIVITY DATA
STABILITY: Stable
INCOMPATIBILITY 鈥? MATERIALS/CONDITIONS TO AVOID:
Heat is generated during cure. Do not cure a mass larger than 50 grams
in a confined space to prevent a premature reaction (exotherm) with
production if intense heat and smoke.
HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon Monoxide and Carbon Dioxide, Toxic Vapors, Gases or
Particulates.
SECTION 6. ENVIRONMENTAL INFORMATION
SPILL RESPONSE:
Refer to other sections of this MSDS for information regarding physical
and health hazards, respiratory protection, ventilation, and personal
protective equipment. Ventilate area. Collect spilled material.
Clean up residue. Place in a U.S. DOT-approved container.
RECOMMENDED DISPOSAL:
Incinerate uncured waste in an industrial or commercial incinerator.
Dispose of completely cured (or polymerized) material in a sanitary
landfill.
ENVIRONMENTAL DATA:
Not determined.
REGULATORY INFORMATION:
Volatile Organic Compounds: 0.0 gms/liter South Coast Air Quality Mgmt
Dist Method.
VOC Less H2O & Exempt Solvents: 0.0 gms/liter South Coast Air Quality
Mgmt Dist Method.
Material Safety Data Sheet
BondPak 2362 Adhesive Part A Page 3 of 5
Since regulations vary, consult applicable regulations or authorities
before disposal.
EPCRA HAZARD CLASS:
FIRE HAZARD: No PRESSURE: No REACTIVITY: No ACUTE: Yes
CHRONIC: Yes
SECTION 7. SUGGESTED FIRST AID
EYE CONTACT:
Immediately flush eyes with large amounts of water for at least 15
minutes. Get immediate medical attention.
SKIN CONTACT:
Immediately wash skin with soap and large amounts of water.
INHALATION:
If signs/symptoms occur, remove person to fresh air. If signs/symptoms
continue, call a physician.
IF SWALLOWED:
Do not induce vomiting. Drink two glasses of water. Call a physician.
SECTION 8. PRECAUTIONARY INFORMATION
EYE PROTECTION:
Wear ventilated goggles. Where safety Glasses with side shields.
SKIN PROTECTION:
Avoid skin contact. Wear appropriate gloves when handling this
material.
RECOMMENDED VENTILATION:
Use with appropriate local exhaust ventilation. Provide appropriate
local exhaust for grinding, cutting or sanding cured material.
Curing ovens must be exhausted to outdoors or to a suitable emission
control device. Provide sufficient ventilation to maintain emissions
below recommended exposure limits. If exhaust ventilation is not
adequate, use appropriate respiratory protection.
RESPIRATORY PROTECTION:
Avoid breathing of vapors. Avoid breathing of dust created by cutting,
sanding or grinding. Select one of the following NIOSH approved
respirators based on airborne concentration of contaminants and in
accordance with OSHA regulations: half-mask dust respirator.
BondPak 2362 Adhesive Part A Page 4 of 5
Material Safety Data Sheet
PREVENTION OF ACCIDENTAL INGESTION:
Wash hands after handling and before eating. Do not ingest.
RECOMMENDED STORAGE:
Store in a cool place. Store away from acids. Store away from heat.
Store out of direct sunlight. Keep container dry. Keep container in
well-ventilated area. Keep out of the reach of children.
FIRE AND EXPLOSION AVOIDANCE:
Keep container tightly closed.
OTHER PRECAUTIONARY INFORMATION:
For industrial or professional use only.
EXPOSURE LIMITS
INGREDIENT VALUE UNIT TYPE AUTH SKIN*
Aliphatic Polymer Diamine NONE NONE NONE NONE
Kaolin 2 MG/M3 TWA ACGIH
RESPIRABLE
Kaolin 10 MG/M3 TWA OSHAV
AS DUST OSHA VACATED PEL
Kaolin 15 MG/M3 TWA OSHA
AS TOTAL DUST
Kaolin 5 MG/M3 TWA OSHA
RESPIRABLE
AMORPHOUS SILICA 5 MG/M3 CEIL CMRG
AS DUST
*SKIN NOTATION:
Listed substances indicated with 鈥榊鈥? under SKIN refer to the potential
contribution to the overall exposure by the cutaneous route including
mucous membrane and eye, either by airborne or, more particularly, by
direct contact with the substance. Vehicles can alter skin absorption.
SOURCE OF EXPOSURE LIMIT DATA:
-ACGIH: American Conference of Governmental Industrial Hygienists
-CMRG: Chemical Manufacturer Recommended Exposure Guidelines
-OSHA: Occupational Safety and Health Administration
-OSHAV: Occupational Safety and Health Administration Vacated PEL.
Vacated Permissible Exposure Limits (PEL) are enforced as the OSHA
PEL in some states. Check with your local regulatory authority.
-NONE: None Established.
SECTION 9. HEALTH HAZARD DATA
EYE CONTACT:
Mild Eye Irritation: signs/symptoms can include redness, swelling,
pain, and tearing.
Material Safety Data Sheet
BondPak 2362 Adhesive Part A Page 5 of 5
Dust created by cutting, grinding, sanding, or machining may cause
eye irritation.
SKIN CONTACT:
Allergic Skin Reaction: signs/symptoms can include redness, swelling,
blistering, and itching.
Mild Skin Irritation (after prolonged or repeated contact):
signs/symptoms can include redness, swelling, and itching.
INHALATION:
Irritation (upper respiratory): signs/symptoms can include soreness of
the nose and throat, coughing and sneezing.
Vapors of heated material may cause irritation of the respiratory
system.
Dust from cutting, grinding, sanding or machining may cause irritation
of the respiratory system.
IF SWALLOWED:
Irritation of Gastrointestinal Tissues: signs/symptoms can include
pain, vomiting, abdominal tenderness, nausea, blood in vomitus, and
blood in feces.
Abbreviations: N/D - Not Determined N/A - Not Applicable CA -
Approximately
The information in this Material Safety Data Sheet (MSDS) is believed
to be correct as of the date issued. BONDPRO CORPORATION MAKES
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for
determining whether the BondPro Corporation product is fit for a
particular purpose and suitable for user鈥檚 methods of use or
application. Given the variety of factors that can affect the use and
application of a BondPro Corporation product, some of which are
uniquely within the user鈥檚 knowledge and control, it is essential that
the user evaluate the BondPro Corporation product to determine whether
it is fit for a particular purpose and suitable for user鈥檚 method of
use or application.
BondPro Corporation provides information in electronic form as a service to its customers. Due
to the remote possibility that electronic transfer may have resulted in errors, omissions or
alterations in this information, BondPro Corporation makes no representations as to its
completeness or accuracy. In addition, information obtained from a database may not be as
current as the information in the MSDS available directly from BondPro Corporation.
|