AM-99
Material Safety Data Sheet
Issue Date: 7/25/03 Revision Date: 8/25/05 Supersedes: 8/25/05
Product Identification:
Manufacturer鈥檚 Name: Applied Membranes, Inc.
Address: 2325 Cousteau Ct., Vista, CA 92081
Phone No.: (760) 727-3711
Applied Membranes, Inc. Name: AM-99
Trade Name: TFC Type RO Membrane Cleaner
Chemical Name: Proprietary
Chemical Formula: Proprietary
Emergency Phone Number: For Chemical Emergency, Spill Leak Fire Exposure or
Accident - Call CHEMTREC Day or Night
DOMESTIC NORTH AMERICA 800-424-9300
INTERNATIONAL, CALL 703-527-3887 (collect calls
accepted)
Hazardous Ingredients:
None
First Aid Measures:
Effects of Exposure
Avoid skin and eye contact and inhalation of dust. Wear overalls, safety glasses or
goggles and chemical resistant gloves and boots. Respiratory protection is required if
airborne concentration is high or unknown. An approved dust/mist respirator may be
worn. Always wash hands before smoking, eating, drinking or using the toilet.
Emergency First Aid Procedures
Ingestion: May cause gastrointestinal irritation with nausea, vomiting and
diarrhea. If conscious, immediately rinse mouth with water & give
water to drink. DO NOT induce vomiting. Seek immediate medical
assistance. Do not give liquids to an unconscious person.
Eye Contact: Causes eye irritation. May cause chemical conjunctivitis.
Immediately irrigate with copious quantities of water for at least 15
minutes. Eyelids to be held open. Seek medical assistance
Skin Contact: May cause skin irritation. Remove contaminated clothing. Wash
affected area with large amount of soap and water. If irritation
develops seek immediate medical assistance.
Page 1 of 3
Applied Membranes, Inc. assumes no liability for results obtained or damages incurred through the improper application of the above
information and data.
Revised 10/18/2005
AM-99 MSDS (continued)
Inhalation: Dust may cause irritation of the respiratory tract. Can produce
delayed pulmonary edema. Remove victim from exposure - avoid
becoming a casualty. Remove contaminated clothing and loosen
remaining clothing. Allow patient to assume most comfortable
position and keep warm. Keep at rest until fully recovered. If
breathing laboured ensure airways are clear and administer oxygen.
If breathing has stopped apply artificial respiration at once. Seek
immediate medical assistance.
Fire Fighting Measures:
Flash Point/Method Material does not exhibit a flash point.
Extinguishing Media: Use extinguishing media appropriate for
surrounding fire. Use water spray, dry chemical,
carbon dioxide or foam.
Special Fire Fighting Procedures: Firefighters should be equipped with appropriate
protective apparel, and Niosh-approved breathing
apparatus.
Unusual Fire and Explosion Hazards: Not considered to be a fire hazard. In sufficient
quantity and reduced particle size, this material is
capable of causing a dust explosion.
Accidental Release Measures:
Spill or Leak Procedures:
Wear proper protective equipment. Ventilate area. Respiratory protection is required in
dusty environment. Sweep up spill but avoid generating dust. With a clean shovel,
transfer spilled material into clean-labeled containers for disposal.
Waste Disposal:
Dispose of according to local, state, and federal pollution regulations.
Handling and Storage:
Precautions to be taken in handling and storage:
Store in a cool, dry, well ventilated place. Keep containers tightly closed. Protect from
physical damage. Store away from incompatible materials.
Exposure Control/ Personal Protection:
Respiratory Protection: dust/mist respirator may be worn
Local Exhaust: Generally Acceptable
Protective Gloves: chemical resistant gloves and boots
Eye Protection: safety glasses or goggles
Other Protective Equipment: Eye-wash; safety shower; protective clothing
Page 2 of 3
Applied Membranes, Inc. assumes no liability for results obtained or damages incurred through the improper application of the above
information and data.
Revised 10/18/2005
AM-99 MSDS (continued)
Physical and Chemical Properties:
Appearance and Odor: Crystalline off-white powder
Physical State: Solid.
pH (1% soln.): 11.0 - 11.5
Solubility in Water: 60g/100ml @ 22掳C
Boiling Point: No data available
Melting Point: >300掳C (decomposes)
Vapor Pressure at 20掳 C (mm. HG.): No data available
approx 0.65g/cm3
Bulk Density:
Stability and Reactivity:
Stability: Stable under normal temperatures and pressures.
Incompatibility: Incompatible with strong oxidizing agents. Avoid
contact with aluminum, zinc, nickel, copper and
copper alloys. Avoid dust generation.
Hazardous Polymerization: Will not occur.
Page 3 of 3
Applied Membranes, Inc. assumes no liability for results obtained or damages incurred through the improper application of the above
information and data.
Revised 10/18/2005
|