Tuesday, March 07, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Durocast Impression Compound
MSDS No.: DOC1001/2
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
1
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
0 0
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
0
1
Last Update: 01-28-2008 Expiration Date:
0
X Liquid Gas Solid
Chemical State:
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
0 Dimethylpolysiloxane Proprietary NE NE 160 C
III. Hazardous Identification:
Hazard Category:
Acute Chronic Fire Pressure Reactive
Hazardous Identification Information:
Non-toxic, non-hazardous.
IV. First Aid Measures:
Route(s) of Entry:
Ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Signs and Symptoms:
Medical Conditions Generally Aggravated by Exposure:
Skin, eye diseases
Emergency and First Aid Procedures:
Tuesday, March 07, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Durocast Impression Compound
MSDS No.: DOC1001/2
Inhalation: No special measures required.
Ingestion: Induce vomiting. Lower the head so that the vomit will not re-enter the mouth and throat. Seek medical attention.
Skin: Wash with soap and water. If irritation occurs, seek medical attention.
Eyes: Rinse with plenty of water for 15 minutes and seek medical attention.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: >160 C Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Foam, carbon dioxide, powder, pulverized water
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
"Empty" containers may contain product residue and may be dangerous. Empty containers should be completely drained and
bunged and then disposed of according to local, state, and federal regulations.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Remove ignition sources (heat, open flame, spark). Soak up with absorbent material (do not use flammable substances such as
sawdust). Dispose according to local, state, and federal regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in tightly closed container. Store at room temperature in original container. Avoid ignition sources (heat, open flame, spark).
Avoid incompatible materials. Use only in well-ventilated areas. Do not smoke while handling this material. Wash thoroughly after
handling.
Other Precautions:
"Empty" containers may contain product residue and may be dangerous. Empty containers should be completely drained and
bunged and then disposed of according to local, state, and federal regulations.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Nothing required.
Tuesday, March 07, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Durocast Impression Compound
MSDS No.: DOC1001/2
IX. Physical and Chemical Properties:
Boiling Point: NE Melting Point: NE
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): NE
Specific Gravity (H20 = 1): 1.23800 Vapor Density (AIR = 1): NE
Solubility In Water: Insoluble Appearance and Odor: Purple paste; lemon odor
Other Information:
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Decomposition/By Products:
Hazardous Polymerization:
Does not occur.
XI. Toxicological Information:
XII. Ecological Information:
Prevent from entering sewers or waterways. Biologically not degradable.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in tightly closed container. Avoid ignition sources (heat, open flame, spark). Avoid incompatible materials. Do not smoke
while handling this material. Wash thoroughly after handling.
XV. Regulatory Information:
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
Tuesday, March 07, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Durocast Impression Compound
MSDS No.: DOC1001/2
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|