Monday, May 08, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Physical Developer (Solution B)
MSDS No.: LPD100/1B
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
1
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
1 0
Emergency Contact: CHEMTREC
OX
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
1
1
Last Update: 2-4-2008 Expiration Date:
0
X Liquid Gas Solid
Chemical State:
H
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
7783859 Ammonium iron (II) sulfate <4.25 NE NE
hexahydrate
5949291 Citric acid monohydrate >1.25 NE NE 212 F
Detergent solutions <1.0
2016560 Dodecylamine acetate <1.0 NE NE 66 C
7782618 Iron (III) nitrate nonahydrate >1.75 NE NE 47.2 C
9016459 Symperonic NP10 <1.0
7732185 Water >92.7 None None 212 F
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
May be harmful if inhaled, ingested, or absorbed by the skin. Respiratory tract irritant. Skin irritant. Severe eye irritant.
The chemical, physical, and toxicological properties of ammonium iron (II) sulfate hexahydrate, iron (III) nitrate nonahydrate, and
citric acid monohydrate have not been thoroughly investigated.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Chronic: Damage to tooth enamel, dermatitis
Signs and Symptoms:
Exposure: Vomiting, diarrhea
Monday, May 08, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Physical Developer (Solution B)
MSDS No.: LPD100/1B
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory diseases
Emergency and First Aid Procedures:
Inhalation: Remove to fresh air immediately. If not breathing, give artificial respiration. If breathing is difficult, give oxygen (To be
administered by qualified medical personnel only!) Get medical attention.
Ingestion: If victim is conscious and alert, wash out mouth with water. (Never give anything by mouth to an unconscious person!)
Get medical attention immediately.
Skin: Flush skin with plenty of soap and water for at least 15 minutes. Remove contaminated clothing. Seek medical attention.
Eyes: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower lids. Do not allow victim to
rub or keep eyes closed. Get medical aid immediately.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Water spray, carbon dioxide, dry chemical powder, appropriate foam
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
Oxidizer--contact with combustible materials may cause a fire.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Wear vapor respirator, safety goggles, and rubber gloves. Remove sources of ignition (i.e. open flames, sparks). Soak up with
inert absorbent material (do not use flammable substances such as sawdust). Ventilate and wash spill site after collection.
Dispose according to local, state, and federal regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in tightly closed container. Air and light sensitive. Keep cool and dry. Avoid ignition sources (heat, open flame, spark).
Avoid incompatible materials. Use only in well-ventilated areas. Avoid inhalation. Avoid contact with skin, eyes, and clothing.
Avoid prolonged or repeated exposure. Wash thoroughly after handling.
Other Precautions:
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Monday, May 08, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Physical Developer (Solution B)
MSDS No.: LPD100/1B
Safety goggles, gloves, vapor respirator, protective clothing
IX. Physical and Chemical Properties:
Boiling Point: ~212 F Melting Point: ~32 F
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): NE
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): NE
Solubility In Water: Soluble Appearance and Odor:
Other Information:
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Strong acids, air sensitive, light sensitive, strong oxidizing agents, bases, reducing agents, nitrates
Decomposition/By Products:
Ammonia, sulfur oxides, nitrogen oxides, carbon monoxide and dioxide
Hazardous Polymerization:
Has not been reported.
XI. Toxicological Information:
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
IATA
Shipping name: Ferric nitrate solution
Hazard class: 5.1
UN no.: 1466
Packing group: III
XV. Regulatory Information:
Monday, May 08, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Physical Developer (Solution B)
MSDS No.: LPD100/1B
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|