Thursday, May 04, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: REDescent Fluorescent Latent Print Powder
MSDS No.: LL701/2
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
1
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
1 1
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
1
1
Last Update: 01-31-2008 Expiration Date:
1
X
Liquid Gas Solid
Chemical State:
F
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
0 Lycopodium 33 NE NE
0 Rocket red AX pigment 66 15 mg/m3 15 mg/m3
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
May be dangerous if ingested. Respiratory tract irritant. Skin irritant. Severe eye irritant.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Chronic: Dermatitis, respiratory sensitization
Signs and Symptoms:
Eyes: Inflammation, redness, watering, itching
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory diseases
Emergency and First Aid Procedures:
Thursday, May 04, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: REDescent Fluorescent Latent Print Powder
MSDS No.: LL701/2
Inhalation: Remove to fresh air. If breathing becomes difficult, give oxygen (To be administered by qualified medical personnel
only!) If breathing stops, perform artificial respiration. Seek medical attention.
Ingestion: If victim is conscious and alert, give large quantities of water. (Never give anything by mouth to an unconscious
person!) DO NOT induce vomiting. If vomiting occurs, lower the head so that the vomit will not re-enter the mouth and throat.
Seek medical attention.
Skin: Wash with soap and water. If irritation occurs, seek medical attention.
Eyes: Rinse with plenty of water for 15 minutes and seek medical attention. DO NOT use an eye ointment.
Convulsions: Do not restrain the victim, but do remove objects with which they might injure themselves; or, orient the victim to
prevent them from striking fixed heavy objects. If the convulsions cease, turn the victim on their side or face down, so that any
fluid in the mouth can drain.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Dry chemical, water spray or fog
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing. Cool containers with water jet in order to prevent pressure
build-up, autoignition, or explosion.
Unusual Fire and Explosion:
Can pose dust explosion hazard if dispersed in air.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Wear dust respirator, safety goggles, and rubber gloves. Sweep up and place in bag or vacuum up with proper filter equipped
instrument. Avoid creating dust. Ventilate and wash spill site after collecting solid. Dispose according to local, state, and federal
regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in tightly closed container. Keep cool and dry. Avoid all ignition sources (heat, open flame, spark). Avoid incompatible
materials. Ground all equipment containing material. Avoid dust creation and accumulation. Use only in well-ventilated areas.
Avoid inhalation and ingestion. Avoid contact with eyes. Wash thoroughly after handling.
Other Precautions:
DO NOT wear contact lenses when using this material.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Safety goggles, gloves, dust respirator, protective clothing
Thursday, May 04, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: REDescent Fluorescent Latent Print Powder
MSDS No.: LL701/2
IX. Physical and Chemical Properties:
Boiling Point: NE Melting Point: NE
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): NE
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): NE
Solubility In Water: Insoluble Appearance and Odor:
Other Information:
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Ignition sources (heat, open flame, spark), strong oxidizers
Decomposition/By Products:
Oxides of carbon, nitrogen, sulfur
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
Rocket red AX pigment contains less than 0.1% free formaldehyde and may be capable of outgassing formaldehyde at levels in
excess of OSHA's action level under some conditions of use.
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in tightly closed container. Keep cool and dry. Avoid all ignition sources (heat, open flame, spark). Avoid incompatible
materials. Ground all equipment containing material. Avoid dust creation and accumulation. Avoid inhalation and ingestion. Avoid
contact with eyes. Wash thoroughly after handling.
XV. Regulatory Information:
Lycopodium is hazardous by definition of OSHA Hazard Communication Standard (29 CFR 1910.1200).
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
Thursday, May 04, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: REDescent Fluorescent Latent Print Powder
MSDS No.: LL701/2
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|