Tuesday, May 02, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Indentation Removal Solution
MSDS No.: IRS100
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
0
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
1 0
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
1
0
Last Update: 01-28-2008 Expiration Date:
0
X Liquid Gas Solid
Chemical State:
H
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
7783188 Ammonium thiosulfate 4-4.5 NE NE
127093 Sodium acetate 0.5-1 NE NE 607 C
7732185 Water 94-94.5 None None 212 F
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
May be harmful if swallowed or absorbed through the skin. Respiratory tract irritant. Skin and eye irritant.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Signs and Symptoms:
Ingestion: Wheezing, chest tightness, stomach upset, hives, faintness, weakness, diarrhea
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory diseases
Emergency and First Aid Procedures:
Tuesday, May 02, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Indentation Removal Solution
MSDS No.: IRS100
Inhalation: Remove to fresh air. If breathing becomes difficult, give oxygen (To be administered by qualified medical personnel
only!) If breathing stops, perform artificial respiration. Seek medical attention.
Ingestion: If victim is conscious and alert, give large quantities of water or milk. (Never give anything by mouth to an
unconscious person!) Only induce vomiting at the instruction of medical personnel. If vomiting occurs, lower the head so that the
vomit will not re-enter the mouth and throat. Seek medical attention.
Skin: Wash with soap and water. If irritation occurs, seek medical attention.
Eyes: Rinse with plenty of water for 15 minutes and seek medical attention.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Use proper extinguishing media suitable for surrounding fire.
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
"Empty" containers may contain product residue and may be dangerous. Empty containers should be completely drained and
bunged and then disposed of according to local, state, and federal regulations.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Wear vapor respirator, safety goggles, and rubber gloves. Soak up with inert absorbent material (vermiculite recommended; do
not use flammable substances such as sawdust). Clean surface thoroughly to remove residual contamination. Dispose according
to local, state, and federal regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in tightly closed container. Avoid incompatible materials. Use only in well-ventilated areas. Avoid contact with skin, eyes,
and clothing. Avoid inhalation. Wash thoroughly after handling.
Other Precautions:
"Empty" containers may contain product residue and may be dangerous. Empty containers should be completely drained and
bunged and then disposed of according to local, state, and federal regulations.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Safety goggles, gloves, vapor respirator, protective clothing
Tuesday, May 02, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Indentation Removal Solution
MSDS No.: IRS100
IX. Physical and Chemical Properties:
Boiling Point: 212 F Melting Point: NE
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): 18
Specific Gravity (H20 = 1): Vapor Density (AIR = 1): 0.6
Solubility In Water: Complete Appearance and Odor:
Other Information: * Appearance & Odor: Light yellow liquid; slight sulfur-vinegar odor
X. Stability and Reactivity:
Stability:
Stable
Incompatibility (Materials to Avoid):
Bases, sodium hypochlorite (bleach), strong oxidizing agents, strong acids
Decomposition/By Products:
Ammonia, sulfur dioxide, nitrogen oxides, chloramine, carbon monoxide and dioxide
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in tightly closed container. Avoid incompatible materials. Avoid contact with skin, eyes, and clothing. Avoid inhalation. Wash
thoroughly after handling.
XV. Regulatory Information:
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
Tuesday, May 02, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Indentation Removal Solution
MSDS No.: IRS100
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|