Wednesday, April 19, 2006
Page 1 of 4
MSDS - Material Safety Data Sheet
Product Name: Fluorescent Magnetic Latent Print Powder
MSDS No.: FMP01
I. Basic Information:
Manufacturer: Sirchie Finger Print Laboratories
1
Address: 100 Hunter Place
City, ST Zip: Youngsville, NC 27596
1 1
Emergency Contact: CHEMTREC
Emergency Telephone Number: 800-424-9300
Contact: Tech Support
Information Telephone Number: 919-554-2244
1
1
Last Update: 01-28-2008 Expiration Date:
1
X
Liquid Gas Solid
Chemical State:
F
Pure Mixture
Chemical Type: X
II. Ingredients:
Trade Secret
EHS IARC SARA
313 OSHA ACGIH Other
% Range NTP SUB Z PEL TLV Limits
CAS No. Chemical Name
7439896 Iron <66 10 mg/m3 5 mg/m3 2,795 F
68611701 Zinc sulfide (green) 32 NE 1 mg/m3
III. Hazardous Identification:
Hazard Category:
X Acute X Chronic Fire Pressure Reactive
Hazardous Identification Information:
Respiratory tract irritant. Skin and eye irritant. May cause siderosis.
Zinc sulfide (green) contains less than 0.5% copper as part of its chemical structure.
This material is subject to the reporting requirements of Section 313 of SARA Title III and 40 CFR Part 373.
IV. First Aid Measures:
Route(s) of Entry:
Inhalation, ingestion, skin, eyes
Health Hazards (Acute and Chronic):
Chronic: Siderosis, dermatitis
Signs and Symptoms:
Inhalation: Coughing, labored breathing
Ingestion: Nausea, vomiting, diarrhea, abdominal pains
Skin: Rash, redness
Medical Conditions Generally Aggravated by Exposure:
Skin, eye, respiratory diseases
Wednesday, April 19, 2006
Page 2 of 4
MSDS - Material Safety Data Sheet
Product Name: Fluorescent Magnetic Latent Print Powder
MSDS No.: FMP01
Emergency and First Aid Procedures:
Inhalation: Remove to fresh air. If breathing becomes difficult, give oxygen (To be administered by qualified medical personnel
only!) If breathing stops, perform artificial respiration. Seek medical attention.
Ingestion: If victim is conscious and alert, give large quantities of water. (Never give anything by mouth to an unconscious
person!) Induce vomiting. Lower the head so that the vomit will not re-enter the mouth and throat. Seek medical attention.
Skin: Wash with soap and water. If irritation occurs, seek medical attention.
Eyes: Rinse with plenty of water for 15 minutes and seek medical attention.
Other Health Warnings:
V. Fire Fighting Measures:
Flash Point: NE Lower Explosive Limit: NE Upper Explosive Limit: NE
F.P. Method:
Fire Extinguishing Media: Dry chemical, sand, graphite
Special Fire Fighting Procedures:
Wear self-contained breathing apparatus and protective clothing.
Unusual Fire and Explosion:
Can pose dust explosion hazard if dispersed in air.
VI. Accidental Release Measures:
Steps to be Taken in Case Material is Released or Spilled:
Wear dust respirator, safety goggles, and rubber gloves. Sweep up and place in bag (use a dust suppressant) or vacuum up with
HEPA filter equipped instrument (recommended). Avoid creating dust. Ventilate and wash spill site after collecting solid. Dispose
according to local, state, and federal regulations.
VII. Handling and Storage:
Precautions to be Taken:
Keep in closed container. Avoid incompatible materials. Use only in well-ventilated areas. Avoid dust generation and
accumulation. Wash thoroughly after handling.
Other Precautions:
DO NOT wear contact lenses while using this product.
VIII. Exposure Controls/Personal Protection:
Ventilation Requirements:
Use only in well-ventilated areas.
Personal Protective Equipment:
Safety goggles, gloves, dust respirator, protective clothing
Wednesday, April 19, 2006
Page 3 of 4
MSDS - Material Safety Data Sheet
Product Name: Fluorescent Magnetic Latent Print Powder
MSDS No.: FMP01
IX. Physical and Chemical Properties:
Boiling Point: NE Melting Point: 2,795 F
Evaporation Rate (Butyl Acetate = 1): NE Vapor Pressure (mm Hg.): NE
Specific Gravity (H20 = 1): 7.50000 Vapor Density (AIR = 1): NE
Solubility In Water: NE Appearance and Odor: Greyish powder; no odor
Other Information:
X. Stability and Reactivity:
Stability:
Normally stable. May be unstable at high temperatures in air.
Incompatibility (Materials to Avoid):
Pure oxygen, strong oxidizers, mineral acids
Decomposition/By Products:
Sulfur oxides, hydrogen sulfide
Hazardous Polymerization:
Will not occur.
XI. Toxicological Information:
Prolonged inhalation of iron oxide dust is known to produce a condition known as siderosis. On x-rays, it appears to be a benign
pneumoconiosis, and is not associated with pulmonary fibrosis or disability unless there is concurrent exposure to other
fibrosis-producing materials such as silica. The TLV is set to protect against siderosis.
XII. Ecological Information:
Prevent from entering sewers or waterways. May be toxic to some aquatic life.
XIII. Disposal Considerations:
Dispose according to local, state, and federal regulations.
XIV. Transport Information:
Keep in closed container. Avoid incompatible materials. Avoid dust generation and accumulation. Wash thoroughly after handling.
XV. Regulatory Information:
This material is subject to the reporting requirements of Section 313 of SARA Title III and 40 CFR Part 373.
XVI. Other Information:
Using this product under normal, properly instructed procedures should not be hazardous.
Wednesday, April 19, 2006
Page 4 of 4
MSDS - Material Safety Data Sheet
Product Name: Fluorescent Magnetic Latent Print Powder
MSDS No.: FMP01
The information above is believed to be accurate and represents the best information currently available to us. However, we make
no warranty of merchantability or any other warranty, expressed or implied, with respect to such information, and we assume no
liability resulting from its use. Users should make their own investigation to determine the suitability of the information for their
particular purposes.
|