Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: meguiars_com_au---m8811-dec-06.asp
                               MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 1 of 10




Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION



PRODUCT NAME
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX

SYNONYMS

"Manufacturer's Code: M88"

PRODUCT USE
Mold release wax.

SUPPLIER
Company: Meguiar' s Australia Pty Ltd
Address:
35 Slough Business Park
Holker St, Silverwater
NSW, 2128
AUS
Telephone: +61 2 9737 9422
Telephone: 1800 804 182
Fax: +61 2 9737 9414




Section 2 - HAZARDS IDENTIFICATION



STATEMENT OF HAZARDOUS NATURE
HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to the Criteria of
NOHSC, and the ADG Code.

POISONS SCHEDULE
None

RISK SAFETY
May cause CANCER. Keep locked up.
Keep container in a well ventilated place.
Avoid exposure - obtain special instructions
before use.
To clean the floor and all objects contaminated
by this material, use water and detergent.
This material and its container must be disposed
of in a safe way.
Keep away from food, drink and animal feeding
stuffs.
Take off immediately all contaminated clothing.
In case of contact with eyes, rinse with plenty
of water and contact Doctor or Poisons
Information Centre.




continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 2 of 10



Section 3 - COMPOSITION / INFORMATION ON INGREDIENTS

NAME CAS RN %
naphtha petroleum, isoparaffin, hydrotreated 64742-48-9. 30-50
distillates, petroleum, light, acid- treated 64742-14-9 20-30
polymer wax blend proprietary 10-25
polydimethylsiloxane 63148-62-9 5-10



Section 4 - FIRST AID MEASURES



SWALLOWED
- If swallowed do NOT induce vomiting.
- If vomiting occurs, lean patient forward or place on left side (head-down position, if
possible) to maintain open airway and prevent aspiration.
- Observe the patient carefully.
- Never give liquid to a person showing signs of being sleepy or with reduced awareness;
i.e. becoming unconscious.
- Give water to rinse out mouth, then provide liquid slowly and as much as casualty can
comfortably drink.
- Seek medical advice.

EYE
If this product comes in contact with the eyes:
- Wash out immediately with fresh running water.
- Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and
moving the eyelids by occasionally lifting the upper and lower lids.
- If pain persists or recurs seek medical attention.
- Removal of contact lenses after an eye injury should only be undertaken by skilled
personnel.

SKIN
If skin contact occurs:
- Immediately remove all contaminated clothing, including footwear
- Flush skin and hair with running water (and soap if available).
- Seek medical attention in event of irritation.

INHALED
- If fumes or combustion products are inhaled remove from contaminated area.
- Lay patient down. Keep warm and rested.
- Prostheses such as false teeth, which may block airway, should be removed, where
possible, prior to initiating first aid procedures.
- Apply artificial respiration if not breathing, preferably with a demand valve
resuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR if necessary.
- Transport to hospital, or doctor.

NOTES TO PHYSICIAN
Treat symptomatically.




continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 3 of 10



Section 5 - FIRE FIGHTING MEASURES



EXTINGUISHING MEDIA
- Foam.
- Dry chemical powder.
- BCF (where regulations permit).
- Carbon dioxide.
- Water spray or fog - Large fires only.

FIRE FIGHTING
- Alert Fire Brigade and tell them location and nature of hazard.
- Wear breathing apparatus plus protective gloves.
- Prevent, by any means available, spillage from entering drains or water courses.
- Use water delivered as a fine spray to control fire and cool adjacent area.
- DO NOT approach containers suspected to be hot.
- Cool fire exposed containers with water spray from a protected location.
- If safe to do so, remove containers from path of fire.
- Equipment should be thoroughly decontaminated after use.

FIRE/EXPLOSION HAZARD
- Combustible.
- Slight fire hazard when exposed to heat or flame.
- Heating may cause expansion or decomposition leading to violent rupture of containers.
- On combustion, may emit toxic fumes of carbon monoxide (CO).
- May emit acrid smoke.
- Mists containing combustible materials may be explosive.
Other combustion products include: carbon dioxide (CO2) and silicon dioxide (SiO2).

FIRE INCOMPATIBILITY
Avoid contamination with strong oxidising agents as ignition may result.

HAZCHEM: None



Section 6 - ACCIDENTAL RELEASE MEASURES



EMERGENCY PROCEDURES

MINOR SPILLS
Remove all ignition sources.
- Clean up all spills immediately.
- Avoid contact with skin and eyes.
- Wear impervious gloves and safety goggles.
- Trowel up/scrape up.
- Place spilled material in clean, dry, sealed container.
- Flush spill area with water.

MAJOR SPILLS
Minor hazard.
- Clear area of personnel and move upwind.
- Alert Fire Brigade and tell them location and nature of hazard.
- Wear breathing apparatus plus protective gloves.
- Prevent, by any means available, spillage from entering drains or water course.
- No smoking, naked lights or ignition sources.
continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 4 of 10
Section 6 - ACCIDENTAL RELEASE MEASURES

- Increase ventilation.
- Stop leak if safe to do so.
- Contain spill with sand, earth or vermiculite.
- Collect recoverable product into labelled containers for recycling.
- Absorb remaining product with sand, earth or vermiculite.
- Collect solid residues and seal in labelled drums for disposal.
- Wash area and prevent runoff into drains.
- If contamination of drains or waterways occurs, advise emergency services.

EMERGENCY RESPONSE PLANNING GUIDELINES (ERPG)
The maximum airborne concentration below which it is believed that nearly all individuals could be exposed
for up to one hour WITHOUT experiencing or developing

life-threatening health effects is:
naphtha petroleum, isoparaffin, hydrotreated 250 mg/m鲁
polydimethylsiloxane 250 mg/m鲁

irreversible or other serious effects or symptoms which could impair an individual's ability to take
protective action is:
naphtha petroleum, isoparaffin, hydrotreated 50 mg/m鲁
polydimethylsiloxane 50 mg/m鲁

other than mild, transient adverse effects without perceiving a clearly defined odour is:
naphtha petroleum, isoparaffin, hydrotreated 30 mg/m鲁
polydimethylsiloxane 30 mg/m鲁

The threshold concentration below which most people will experience no appreciable risk of health effects:
naphtha petroleum, isoparaffin, hydrotreated 10 mg/m鲁
polydimethylsiloxane 10 mg/m鲁

American Industrial Hygiene Association (AIHA)

Ingredients considered according to the following cutoffs
Very Toxic (T+) >= 0.1% Toxic (T) >= 3.0%
R50 >= 0.25% Corrosive (C) >= 5.0%
R51 >= 2.5%
else >= 10%
where percentage is percentage of ingredient found in the mixture

Personal Protective Equipment advice is contained in Section 8 of the MSDS.



Section 7 - HANDLING AND STORAGE



PROCEDURE FOR HANDLING
Remove all ignition sources.
- Limit all unnecessary personal contact.
- Wear protective clothing when risk of exposure occurs.
- Use in a well-ventilated area.
- When handling DO NOT eat, drink or smoke.
- Always wash hands with soap and water after handling.
- Avoid physical damage to containers.
- Use good occupational work practice.
- Observe manufacturer's storing and handling recommendations.


continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 5 of 10
Section 7 - HANDLING AND STORAGE

SUITABLE CONTAINER
- Metal can or drum
- Packaging as recommended by manufacturer.
- Check all containers are clearly labelled and free from leaks.

STORAGE INCOMPATIBILITY
Avoid storage with oxidisers and acids.

STORAGE REQUIREMENTS
- Store in original containers.
- Keep containers securely sealed.
- No smoking, naked lights or ignition sources.
- Store in a cool, dry, well-ventilated area.
- Store away from incompatible materials and foodstuff containers.
- Protect containers against physical damage and check regularly for leaks.
- Observe manufacturer's storing and handling recommendations.



Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION



EXPOSURE CONTROLS
Source Material TWA TWA STEL STEL Peak Peak TWA
ppm mg/m鲁 ppm mg/m鲁 ppm mg/m鲁 F/CC
_________________ __________________ ______ ______ ______ ______ ______ ______ ______
Australia Exposure distillates, 5
Standards petroleum, light,
acid- treated (Oil
mist, refined
mineral)

The following materials had no OELs on our records
鈥? naphtha petroleum, isoparaffin, hydrotreated: CAS:64742-48-9
鈥? polydimethylsiloxane: CAS:63148-62-9




MATERIAL DATA
None assigned. Refer to individual constituents.

INGREDIENT DATA
NAPHTHA PETROLEUM, ISOPARAFFIN, HYDROTREATED:
POLYDIMETHYLSILOXANE:
No exposure limits set by NOHSC or ACGIH.

NAPHTHA PETROLEUM, ISOPARAFFIN, HYDROTREATED:

REL TWA: 400 ppm [EXXON]
for petroleum distillates:
CEL TWA: 500 ppm, 2000 mg/m3 (compare OSHA TWA).

DISTILLATES, PETROLEUM, LIGHT, ACID-TREATED:
REL TWA: 300 ppm [Manufacturer]
Human exposure to oil mist alone has not been demonstrated to cause health effects
except at levels above 5 mg/m3 (this applies to particulates sampled by a method that
does not collect vapour). It is not advisable to apply this standard to oils containing
continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 6 of 10
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION

unknown concentrations and types of additive.
WARNING: This substance is classified by the NOHSC as Category 2 Probable Human
Carcinogen.

POLYDIMETHYLSILOXANE:

PERSONAL PROTECTION

EYE
- Safety glasses with side shields; or as required,
- Chemical goggles.
- Contact lenses may pose a special hazard; soft contact lenses may absorb and
concentrate irritants. A written policy document, describing the wearing of lens or
restrictions on use, should be created for each workplace or task. This should include a
review of lens absorption and adsorption for the class of chemicals in use and an account
of injury experience. Medical and first-aid personnel should be trained in their removal
and suitable equipment should be readily available. In the event of chemical exposure,
begin eye irrigation immediately and remove contact lens as soon as practicable. Lens
should be removed at the first signs of eye redness or irritation - lens should be
removed in a clean environment only after workers have washed hands thoroughly. [CDC
NIOSH Current Intelligence Bulletin 59].

HANDS/FEET
Wear protective gloves, eg. PVC.

OTHER
- Overalls.
- Eyewash unit.

RESPIRATOR
Selection of the Class and Type of respirator will depend upon the level of breathing
zone contaminant and the chemical nature of the contaminant. Protection Factors (defined
as the ratio of contaminant outside and inside the mask) may also be important.

Breathing Zone Level Maximum Protection Half- face Respirator Full- Face Respirator
ppm (volume) Factor
1000 10 A- AUS P -
1000 50 - A- AUS P
5000 50 Airline * -
5000 100 - A- 2 P
10000 100 - A- 3 P
100+ Airline**

* - Continuous Flow ** - Continuous-flow or positive pressure demand.

The local concentration of material, quantity and conditions of use determine the type of
personal protective equipment required.
For further information consult site specific
CHEMWATCH data (if available), or your
Occupational Health and Safety Advisor.

ENGINEERING CONTROLS
Use in a well-ventilated area.
General exhaust is adequate under normal operating conditions. If risk of overexposure
exists, wear SAA approved respirator. Correct fit is essential to obtain adequate
protection. Provide adequate ventilation in warehouse or closed storage areas.
continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 7 of 10
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION




Section 9 - PHYSICAL AND CHEMICAL PROPERTIES



APPEARANCE
Cream coloured paste with a slight hydrocarbon odour; insoluble in water.

PHYSICAL PROPERTIES
Does not mix with water.
Floats on water.

Molecular Weight: Not Applicable Boiling Range (掳C): 199 approx.
Melting Range (掳C): Not Available Specific Gravity (water=1): 0.86
Solubility in water (g/L): Immiscible pH (as supplied): Not Applicable
pH (1% solution): Not Applicable Vapour Pressure (kPa): <2.66 @ 21C
Volatile Component (%vol): 53 (VOC) Evaporation Rate: <1
Relative Vapour Density (air=1): >1 Flash Point (掳C): >65.56
Lower Explosive Limit (%): Not Available Upper Explosive Limit (%): Not Available
Autoignition Temp (掳C): Not Available Decomposition Temp (掳C): Not Available
State: Non Slump Paste Viscosity: Not Available



Section 10 - CHEMICAL STABILITY AND REACTIVITY INFORMATION



CONDITIONS CONTRIBUTING TO INSTABILITY
- Presence of incompatible materials.
- Product is considered stable.
- Hazardous polymerisation will not occur.



Section 11 - TOXICOLOGICAL INFORMATION



POTENTIAL HEALTH EFFECTS

ACUTE HEALTH EFFECTS

SWALLOWED
Considered an unlikely route of entry in commercial/industrial environments.
The material is moderately discomforting and may be harmful if swallowed.
Ingestion may result in nausea, abdominal irritation, pain and vomiting.

EYE
The material is discomforting to the eyes and is capable of causing a mild, temporary
redness of the conjunctiva (similar to wind-burn), temporary impairment of vision and/ or
other transient eye damage/ ulceration.

SKIN
The material may be discomforting to the skin if exposure is prolonged and is capable of
causing skin reactions which may lead to dermatitis from repeated exposures over long
periods.
The material may accentuate any pre-existing skin condition.



continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 8 of 10
Section 11 - TOXICOLOGICAL INFORMATION

INHALED
The vapour is discomforting to the upper respiratory tract.
Inhalation hazard is increased at higher temperatures.
Acute effects from inhalation of high vapour concentrations may be chest and nasal
irritation with coughing, sneezing, headache and even nausea.
Not considered to cause discomfort through normal use.

CHRONIC HEALTH EFFECTS
Principal routes of exposure are usually by inhalation of vapour and skin contact with
the material.
Prolonged or continuous skin contact with the liquid may cause defatting with drying,
cracking, irritation and dermatitis following.
Chronic solvent inhalation exposures may result in nervous system impairment
and liver and blood changes. [PATTYS].
As with any chemical product, contact with unprotected bare skin; inhalation of vapour,
mist or dust in work place atmosphere; or ingestion in any form, should be avoided by
observing good occupational work practice.

TOXICITY AND IRRITATION
Not available. Refer to individual constituents.

NAPHTHA PETROLEUM, ISOPARAFFIN, HYDROTREATED:
No significant acute toxicological data identified in literature search.

DISTILLATES, PETROLEUM, LIGHT, ACID-TREATED:
No data of toxicological significance identified in literature search.

POLYDIMETHYLSILOXANE:
TOXICITY IRRITATION
Inhalation (rat) LC50: >1100 mg/m鲁* Eye (rabbit): 100 mg/1h - Mild
Oral (rat) LD50: >35000 mg/kg*
Dermal (rabbit) LD50: >3000 mg/kg*
The material may be irritating to the eye, with prolonged contact causing inflammation.
Repeated or prolonged exposure to irritants may produce conjunctivitis.
No toxic response noted during 90 day subchronic inhalation toxicity
studies
The no observable effect level is 450 mg/m鲁.
Non-irritating and non-sensitising in human patch test. [Xerox]*




Section 12 - ECOLOGICAL INFORMATION

No data for Meguiar's M88 - Universal Mold Release Wax.
Refer to data for ingredients, which follows:

NAPHTHA PETROLEUM, ISOPARAFFIN, HYDROTREATED:
DO NOT discharge into sewer or waterways.

POLYDIMETHYLSILOXANE:
Fish LC50 (96hr.) (mg/l): 10000




continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 9 of 10



Section 13 - DISPOSAL CONSIDERATIONS

- Consult manufacturer for recycling options and recycle where possible .
- Consult State Land Waste Management Authority for disposal.
- Incinerate residue at an approved site.
- Recycle containers if possible, or dispose of in an authorised landfill.



Section 14 - TRANSPORTATION INFORMATION

HAZCHEM: None



NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS:UN, IATA,
IMDG



Section 15 - REGULATORY INFORMATION



POISONS SCHEDULE: None

REGULATIONS
naphtha petroleum, isoparaffin, hydrotreated (CAS: 64742-48-9) is found on the following
regulatory lists;
Australia High Volume Industrial Chemical List (HVICL)
Australia Inventory of Chemical Substances (AICS)
Australia Poisons Schedule
International Council of Chemical Associations (ICCA) - High Production Volume List
OECD Representative List of High Production Volume (HPV) Chemicals

distillates, petroleum, light, acid-treated (CAS: 64742-14-9) is found on the following
regulatory lists;
Australia Exposure Standards
Australia Inventory of Chemical Substances (AICS)
Australia Poisons Schedule
OECD Representative List of High Production Volume (HPV) Chemicals

polydimethylsiloxane (CAS: 63148-62-9) is found on the following regulatory lists;
Australia - Australia New Zealand Food Standards Code - Food Additives - Schedule 2
Miscellaneous additives permitted in accordance with GMP in processed foods specified in
Schedule 1
Australia - Australia New Zealand Food Standards Code - Processing Aids - Permitted
antifoam agents
Australia Inventory of Chemical Substances (AICS)
Australia Standard for the Uniform Scheduling of Drugs and Poisons (SUSDP) - Schedule
4
IMO MARPOL 73/78 (Annex II) - List of Other Liquid Substances
OECD Representative List of High Production Volume (HPV) Chemicals




continued...
MEGUIAR'S M88 - UNIVERSAL MOLD RELEASE WAX
Chemwatch Material Safety Data Sheet
Issue Date: 18-Nov-2006 CHEMWATCH 4912-22
NA317EC CD 2006/4 Page 10 of 10



Section 16 - OTHER INFORMATION



This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or
criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written permission
from CHEMWATCH. TEL (+61 3) 9572 4700.

Issue Date: 18-Nov-2006
Print Date: 11-Dec-2006

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
meguiars_com_au---m26-dec-06.asp N/A
meguiars_com_au---m2805-dec-06.asp N/A
meguiars_com_au---m34-dec-06.asp 1569-01-3 57-55-6 7732-18-5
meguiars_com_au---m4001-dec-06.asp N/A
meguiars_com_au---m4516-dec-06.asp N/A
meguiars_com_au---m46-jul-05.asp N/A
meguiars_com_au---m49-dec-06.asp N/A
meguiars_com_au---m52-jan-07.asp 1569-01-3 57-55-6 7732-18-5
meguiars_com_au---m64-jul-05.asp 577-11-7
meguiars_com_au---m8811-dec-06.asp N/A
meguiars_com_au---mc200-jan-08.asp 68608-26-4 68439-46-3 1569-01-3
meguiars_com_au---mc201-jan-08.asp 1569-01-3 57-55-6
meguiars_com_au---mc202-jan-08.asp N/A
meguiars_com_au---mc203-jan-08.asp N/A
meguiars_com_au---mc204-jan-08.asp N/A
meguiars_com_au---mc205-jan-08.asp N/A
meredithdist_com_au---ac100_pro_part_a.asp 6606-59-3
meredithdist_com_au---ac100_pro_part_b.asp N/A
meredithdist_com_au---bostik_1465.asp N/A
meredithdist_com_au---bostik_aquashield_sb40.asp N/A
meredithdist_com_au---bostik_firecaulk.asp N/A
meredithdist_com_au---bostik_kitchen_bathroom_silicone_acetic_cure.asp N/A
meredithdist_com_au---bostik_roof_gutter_silicone.asp N/A
meredithdist_com_au---bostik_seal_n_flex_ac.asp N/A
meredithdist_com_au---bostik_seal_n_flex_trafficable.asp N/A
meredithdist_com_au---bostik_ultragrip.asp N/A
meredithdist_com_au---bostik_ultraseal.asp N/A
meredithdist_com_au---chem_stud_.asp N/A
meredithdist_com_au---csr_hebel_data_sheet_mungo_mn_mnl.asp N/A
meredithdist_com_au---csr_hebel_data_sheet_zip_it.asp N/A
meredithdist_com_au---hammer_capsule_.asp N/A
meredithdist_com_au---junior_powerfoam.asp N/A
meredithdist_com_au---kf2_.asp N/A
meredithdist_com_au---long_screws.asp N/A
meredithdist_com_au---metalcuttingcompound.asp N/A
meredithdist_com_au---mungo.asp N/A
meredithdist_com_au---pbi_structural_anchor.asp N/A
meredithdist_com_au---siliconespray.asp N/A
meredithdist_com_au---stainless_steel_screws.asp N/A
meredithdist_com_au---techflow_grout_hs.asp N/A
meredithdist_com_au---timberdeks.asp N/A
meredithdist_com_au---trak_it_fuel_cell.asp N/A
meredithdist_com_au---trdac_12100_12150_load_capacities.asp N/A
meredithdist_com_au---trdac_12100_pamphlet.asp N/A
meredithdist_com_au---triggerfoam.asp N/A
meredithdist_com_au---vertigo.asp N/A
meredithdist_com_au---wall_dog.asp N/A
micro-beads_com---msds_dynoseeds_pcs.asp 2003-06-1 9003-53-6
micro-beads_com---msds_dynoseeds_ts.asp 2003-06-1 9003-53-6
micro-beads_com---msds_rondure.asp 2004-05-1 9003-53-6

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC