TRDAC
The ultimate in tie-down
connectors TRDAC12100 Screwbolt
UPLIFT CAPACITIES DERIVED IN
ACCORDANCE WITH AS1684-1999
TRDAC Top Plate Tie Down Anchor
Product description
The new revolutionary
TRDAC12100 Screwbolt is Description mm mm qty qty
TRDAC12100 12 x 100mm 12 12 25 150
manufactured from high strength
carbon steel and consists of two
key features,
鈥? Patented thread design for high
expansion free performance
鈥? Internal M12 thread to
facilitate M12 threaded rod
The TRDAC12100 Screwbolt is a
quick and simple system, which
provides timber frame top plate
tie-down to slabs for residential
timber frame construction without
the costly time consuming
requirements of chemical
anchoring systems. Its unique
thread design provides an 35mm TRDAC 12100 SCREWBOLT鈩?
undercutting effect in the concrete
ensuring optimum performance in
residential slabs at minimal edge
distance (e.g. 35mm).
20MPa concrete
Major Benefits
鈥? Faster & easier installation
Minimum edge distance as per table
鈥? Simple operation
Anchor embedment depth 65mm for 12 x 100 SCREW-BOLT
鈥? No wastage
鈥? Labour saving LIMIT STATE DESIGN
Uplift capacity of wall frame tie-down connections using Powers connectors
鈥? Cost saving Position of tie-down connection Uplift Capacity (kN)
Top or Bottom plates to slab Unseasoned timber Seasoned timber
Anchor Size Min. Edge Dist mm J2 J3 J4 JD4 JD5 JD6
12 x 100mm 35 10 10 10 10 10 10
鈮?45
12 x 100mm 11 11 11 11 11 11
50 x 50 x 3.0 (min) washer to be used with the 12 mm TRDAC 12100 SCREWBOLT鈩?
NOTE: For bottom plates greater than 35mm but 50mm or less in thickness, Limit State Design uplift capacities listed above shall be multiplied by 0.85.
TRDAC 12100 SCREWBOLT鈩? uplift capacities have been devived in accordance with AS 1684-1999 requirements for top or bottom plates to slab
tie down connections.
VIC HQ:
5-7 HENLEY CRT
MOORABBIN VIC 3189
T 03-9553 3999
F 03-9553 4400
NSW:
4 ALBAN STREET
LIDCOMBE NSW 2141
Installation Procedure
T 02-9748 7766
F 02-9648 5977
QLD:
UNIT 7 / LOT 3
70 FLANDERS ST
SALISBURY QLD 4107
T 07-3216 7122
F 07-3216 7216
FAR NORTH QLD:
T 0439 083 646
F 07-4036 4166
1 Using the proper diameter bit, drill a hole 2 Blow the hole clean of dust and other
into the base material to a depth of at material.
SA:
least one to two anchor diameters
UNIT 15 / 36-38 TIKALARA ST
deeper than the embedment required.
REGENCY PARK SA 5010
T 08-8346 5611
F 08-8346 5711
TAS:
34 DERWENT PARK RD
DERWENT PARK TAS 7009
T 03-6273 5800
F 03-6273 4977
WA:
PO BOX 3380
MALAGA WA 6090
T 08-9248 1004
3 4 Installation tips:
F 08-9248 1006
鈥? Insert the anchor through the fixture into 鈥? Use quality hexagonal socket with a ratchet
the anchor hole spanner
NZ:
鈥? Begin tightening the anchor by applying 鈥? Where substrate allows, a torque controlled
forward pressure when engaging the first impact wrench can be used.
PO BOX 302 076
thread. 鈥? During installation debris or dust created
NORTH HARBOUR
Additional initial forward pressure may by the thread cutting action may cause
be required for installation in high some resistance to be experienced. This is
AUCKLAND
strength, dense base material. easily overcome by unscrewing the TRDAC
T (64) 9415 2425
鈥? Continue tightening the anchor until the 12100 SCREWBOLT鈩? for one turn, or
F (64) 9415 2627
head is seated against the fixture. more and then continue to fix to the full
鈥? In extremely dense materials, use of an embedment
impact wrench is recommended.
鈥? The installation is now complete.
|