501 鈥? 505 Olsen Avenue, Molendinar Qld 4214
Phone 61 7 5585 7000 Fax 61 7 5539 6399
Rhino PP1195
(Formerly PP95)
Technical Data Sheet
Previous Revision Date: 07- February 2002
Revised Date: 10-December-2007
PRODUCT DESCRIPTION
domestic, construction and commercial
Rhino PP1195 is a 100% solid, spray applied, pure
waterproofing, potable water storage applications,
polyurea elastomeric coating that exhibits excellent
impact and urine resistant coatings for livestock
chemical, impact and abrasion resistance, as well as
transport, wear and impact resistant linings for
elongation and tear strength.
mining and materials handling industries etc.
FEATURES TYPICAL PHYSICAL PROPERTIES
Rhino PP1195, being a pure polyurea, is moisture
and temperature tolerant, enabling applications to Wet
Solids by weight: 100%
take place in extreme environments. Unlike
Solids by volume: 100%
standard polyurethanes, Rhino PP1195 will fully
VOC: nil
cure and exhibit full mechanical properties even
Solvent: nil
when applied in high humidity, cold or moist
Viscosity A (Iso): 490 (cps@ Brookfield Spindle 3)
substrate scenarios. Viscosity B (Polyol): 440 (cps@ Brookfield Spindle 3)
Mix Ratio: 1:1 by volume
Rhino PP1195 cures in seconds and can be walked
Coverage per litre: approx 1sqm @ DFT of 1mm
on within minutes of application. Rhino PP1195
Weight per litre: 1.07kg
contains no solvents, catalysts or VOC鈥檚. As a result,
Gel Time: 5 to 7 seconds
its cure is not affected by moisture or temperature.
Tack Free: 15 to 25 seconds
Rhino PP1195 can be built up to any required Re-coat: same day
thickness in the one continuous application and as 95% Cure 24 hours
such can be applied to vertical and overhead
surfaces. Dry
Hardness (Shore A): 95 (+/-5)
Rhino PP1195 is an ideal product for mining and
Abrasion Resistance: <30mg loss(1kg,1000rev,H-18wheel)
industrial applications where rapid turn-around times
Stress/Tensile strength: 3450psi (+/-200psi) [ASTM D-412]
are of paramount concern. It is spray applied and Tear Resistance Die C: 530pli (+/-20pli) [ASTM D-624]
provides a seamless coating that is extremely tough Elongation: 252% (@ 25掳C)
and durable, whilst remaining flexible to Water Absorption <1% (@25deg C/24hr)
accommodate substrate movement. Permeability Untested
Potable Water Passed at Max test exposure levels
Rhino PP1195 pure polyurea can be applied to a
(AS/NZ 4020)
wide range of prepared substrate including concrete,
Service temperature: -40掳 to 125掳C
steel, fibreglass, aluminium, AC sheet, timber,
Clean up: Acetone
various polyurethane foams, polystyrene foams and Thinner: Not used
geotextiles. Shelf life: 1 year (@ 15掳 to 30掳C (Unopened)
APPLICATION
USES
Rhino PP1195 pure polyurea is only applied by
Uses for Rhino PP1195 pure polyurea include:
authorised Rhino Linings applicators in strict
primary and secondary chemical containment,
accordance with procedures supplied by the
protection against hydrogen sulphide attack in
manufacturer. Correct substrate preparation is
sewage and wastewater applications, corrosion
essential for optimum coating performance. Contact
control on structural steel (including pipeline
technical service personnel for full MSDS, storage
protection and marine applications), steam-
information and for substrate preparation, priming and
cleanable floors and walls in abattoir and food
coating specifications.
processing plants, general
Disclaimer: The information provided herein and/or otherwise supplied is done so in good faith and is deemed to be reliable. As such any recommendations or
conclusions are made without liability on the part of Rhino Linings Australasia Pty Ltd and/or any of the company鈥檚 employees or associates. It is recommended that
each user conduct a sufficient investigation as to the suitability of this product for any particular use as Rhino Linings Australasia Pty Ltd accepts no liability,
expressed, implied or incidental, for any injury, loss or damage resulting from reliance upon such information and/or from any subsequent use of the product
|