MATERIAL SAFETY DATA SHEET
SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Chemical Name And Synonyms : Ultra High Molecular weight Polyethylene
Chemical Family : Polyolefin
Trade Name & Synonyms : Relene Ultra
C.A.S. No. : 9002-88-4
Formula : ( CH2 -CH2) n
Manufacturer's Name : Relene Petrochemicals Pvt. Ltd
Address : Product Application & Research Centre
V N Purav Marg, Chembur,
Mumbai - 400071, India
Emergency Telephone No : 91-22-30515000
SECTION 2 - COMPOSITION / INFORMATION ON INGREDIENTS
Paints Preservatives & Solvents % TLV Alloys & Metallic % TLV
(units)Coatings (units)
NIL NA NIL NA
Pigments Base metal
< 0.01 NA NIL NA
Catalyst Alloys
NIL NA NIL NA
Vehicle Metallic coatings
NIL NA NIL NA
Solvents Filler Metal plus
coating or core flux
<1 NA NIL NA
Additives Others
NIL NA
Hazardous Mixtures of Other Liquids, Solids or Gases
Relene Ultra Polyethylene resins are not considered to be hazardous under normal processing
conditions
SECTION 3 - HAZARDS IDENTIFICATION
POTENTIAL HEALTH EFFECTS
鈥? EYE CONTACT
Particulate may scratch eye surfaces / cause mechanical irritation
鈥? SKIN CONTACT
Negligible hazard at ambient temperatures (-18 to + 50 掳 C; 0 to 100 掳 F). Exposure to hot
material may cause thermal burns
鈥? INHALATION
Negligible hazard at ambient temperatures (-18 to + 50 掳 C; 0 to 100 掳 F). Vapors that may be
formed at elevated temperatures may be irritating to eyes and respiratory tract
鈥? INGESTION
Not toxic
1
MATERIAL SAFETY DATA SHEET
SECTION 4 - FIRST AID MEASURES
鈥? EYE CONTACT
This product is an inert solid. If in eye, remove as one would any foreign object
鈥? SKIN CONTACT
In case of adverse exposure to hot material, immediately immerse in or flush the affected area
with large amounts of cold water to dissipate heat. Cover with clean cotton sheeting and get
prompt medical attention. No attempt should be made to remove material from skin or to remove
contaminated clothing, as the damaged flesh can be easily torn.
鈥? INHALATION
In case of adverse exposure to vapors formed at elevated temperatures, immediately remove the
affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at
rest. Call for prompt medical attention.
鈥? INGESTION
First aid is normally not required
SECTION 5 - FIRE FIGHTING MEASURES
Flash Ignition Temperature - 335 掳 C LEL N/A
Auto Ignition Temperature - 350 掳C UEL N/A
Flammable limits N/A
Extinguishing Media Water, Dry Chemical, Co2, Foam
Special Fire Fighting Procedures: Relene resins are combustible materials - molten
Polyethylene tends to flow or drip and will propagate fire. Respiratory and eye protection required
for fire fighting personnel
Unusual Fire and Explosion Hazards : Failure or malfunction of temperature control systems
on processing equipment such as extruders may create explosion hazard
SECTION 6 - ACCIDENTAL RELEASE MEASURES
LAND SPILL
Recover spilled material and place in suitable containers for recycle or disposal. Pellets released
or spilled during shipping or storage may create a slipping hazard and should be removed from
walkways. Consult an expert on disposal of recovered material and ensure conformity to local
regulations.
SECTION 7 - STORAGE AND HANDLING
Storage Temperature,掳C : Ambient
Loading / Un-Loading Temperature, 掳C : Ambient
Storage / Transport Pressure, mm Hg : Atmospheric
Loading / Un-Loading Viscosity, cSt : Solid
Storage and Handling : Store in a cool, well ventilated place away from
incompatible materials. DO NOT handle or store near an open flame, heat or other sources of
ignition. Protect material from direct sunlight. Material will accumulate static charges that may
cause an electrical spark (ignition source). Use proper grounding procedures.
2
MATERIAL SAFETY DATA SHEET
SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Respiratory Protection (Specify type) : NONE
Special --
Ventilation Local Exhaust
recommended for high temperature processing
Mechanical (General) -- Other --
Protective Gloves : Use gloves when handling hot melt
Eye Protection : Use goggles when handling hot melt
Other Protective Equipment : Long sleeve shirts & long cotton pants to protect skin contact with
hot melt
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
N/A 0.92 - 0. 94
Specific Gravity (H2O=1)
Boiling Point (掳C)
N/A <0.1
Vapour Pressure (mm Hg.) Percent Volatile by volume (%)
N/A N/A
Vapour Density, at 1 atm (Air=1) Evaporation Rate
Insoluble
Solubility in water
Appearance and odour: White powder, No Specific Odour
SECTION 10 - STABILITY AND REACTIVITY
-
Stability Unstable Conditions to avoid
Stable 鉁? Heating above 350掳c, direct flame
Incompatibility (materials to avoid): Strong oxidants at high temperature
Hazardous decomposition products CO, CO2, HYDROCARBONS, SMOKE, ACROLEIN *
-
Hazardous Polymerisation May occur Conditions to avoid
NA
Will not occur 鉁?
* Decomposition products may vary in nature depending upon actual conditions; e.g.
availability of oxygen; temperature and presence of other materials
SECTION 11 - TOXICOLOGICAL INFORMATION
Please refer to Section 3 for available information on potential health effects
SECTION 12 - ECOLOGICAL INFORMATION
No specific ecological data are available for this product. Please refer to Section 6 for information
regarding accidental releases and Section 15 for regulatory reporting information.
3
MATERIAL SAFETY DATA SHEET
SECTION 13 - DISPOSAL CONSIDERATIONS
Waste disposal method: Landfill Or Incineration. Please refer to Sections 5,6 and 15 for disposal
and regulatory information.
SECTION 14 - TRANSPORT INFORMATION
Not applicable, This product is not transport regulated
SECTION 15 - REGULATORY INFORMATION
Product meets the requirements stipulated in IS 10146 鈥? 1982 on 鈥淪pecification for Polyethylene
and its copolymers for safe use in contact with foodstuffs, pharmaceuticals and drinking water鈥?.
Additives incorporated in this grade conform to the positive list of constituents as prescribed in IS
10141 鈥? 1982.
The product and the additives incorporated in it also comply with the FDA: CFR Title 21,
177.1520 olefin polymers.
SECTION 16 - OTHER INFORMATION
Ecotoxicity : Not toxic under normal conditions
Persistence : Non-biodegradable
MANUFACTURER'S DATA:
REGD. OFFICE : MANUFACTURING PLANTS :
RELIANCE INDUSTRIES LIMITED RELENE PETROCHEMICALS PVT LTD
MAKER IV, NARIMAN POINT, Post Box No. 14, Ghansoli P.O.Thane
MUMBAI - 400 021
Belapur Road, Navi Mumbai 鈥? 400 701
TEL : 022-30324000
FAX : 022-30327399
REVISION SUMMARY:
Since April, 2005 this MSDS has been revised
Disclaimer:
This information relates to the specific material designated and may not be valid for such material used in combination
with any other materials or in any process. Information contained in this Material Safety Data Sheet is to the best of our
knowledge and believed to be reliable but no representation, guarantee or warranties of any kind are made as to its
accuracy, suitability for a particular application etc. It is upto the user / distributor to ensure that the information contained
in the material safety data sheet is relevant to the product manufactured or sold as the case may be. Reliance Industries
Limited and Reliance Group of Companies makes no warranties, expressed or implied, in respect of the adequacy of
this document for any particular purpose.
4
|